Fitness Reality 2809D.2 User manual

2809D.2 -081821
IMPORTANT: Read all instructions carefully before using this product.
Retain this owner’s manual for future reference. The specifications of this
product may vary from this photo and, subject to change without notice.
Multi-Function Adjustable Power Rack
Squat Stand

PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE.
See the Service page for other methods of contacting customer support
Automatically set up an
Email to CUSTOMER
SERVICE by SCANNING this
QR code with the Camera or
a QR code scanner APP on
your smart device.

SERVICE..........................................................................................................................2
LABEL PLACEMENT........................................................................................................3
IMPORTANT SAFETY GUIDEILNES................................................................................4
ASSEMBLY PREPARATION.............................................................................................5
OVERVIEW DRAWING ....................................................................................................6
PART LIST........................................................................................................................7
HARDWARE PACK...........................................................................................................8
PRODUCT DRAWING....................................................................................................10
STEP 1 ...........................................................................................................................11
STEP 2 ...........................................................................................................................13
STEP 3 ...........................................................................................................................15
STEP 4 ...........................................................................................................................17
STEP 5 ...........................................................................................................................19
STEP 6 ...........................................................................................................................21
WARRANTY ...................................................................................................................23
PARTS REQUEST FORM ..............................................................................................24
TABLE OF CONTENTS
1

IMPORTANT: FOR NORTH AMERICA ONLY
For damaged or defective product, questions, replacement parts or any other service support,
please contact our customer service department by the below methods:
1. Scan the QR code with the camera or any QR code scanner
app on your smart device. This will bring you to a direct
email to send to CUSTOMER SERVICE in the format shown
below for your equipment.
2. Email: [e-mail]
a. Response Time: 1-2 Business Days
3. Website: www.paradigmhw.com
4. Phone: Toll-Free: 1-844-641-7920
a. Monday thru Friday (PST)
b. Response time may vary via calling
c. Refer to our email for the best response time
Please have the following information ready when requesting for service:
Your name
Shipping address
Phone number
Model number
Serial number
Part number
Proof of Purchase
Paradigm Health & Wellness, Inc.
1189 Jellick Ave.
City of Industry, CA 91748, USA
SERVICE
2
Fastest and Easiest method
to set up a customer service
response.

LABEL PLACEMENT
3
Model# 2809D

WARNING: Before using this equipment you should consult with your physician if you
have any of the following conditions or ailments:
Extreme obesity
Glaucoma, retinal detachment or conjunctivitis
Pregnancy
Spinal injury, Cerebral Sclerosis, or acutely swollen joints
Middle ear infection
High blood pressure, Hypertension, Recent stroke or Transient ischemic attack
Heart or circulatory disorders for which you are being treated
Hiatus hernia or Ventral hernia
Bone weaknesses including Osteoporosis, Unhealed fractures, Modularly pins, or Surgically
implanted orthopedic supports
Use of anti-coagulants including Aspirin in high doses
The Maximum Static Weight Capacity for this product is 800lbs / 363kgs.
Read all the instructions carefully before assembling or operating this product. Retain this
owner’s manual, do not remove any safety labels from the machine and keep the original
purchase receipt for future reference.
This workout equipment is designed and built for optimum safety. However, certain precautions
apply whenever you operate this exercise equipment. Be sure to read the entire manual before
assembling and operating this equipment. Also, note the following safety instructions:
1. Consult your physician or other health care professionals before using this equipment.
2. Always wear proper exercise apparel when using this equipment. Use care when getting on or
off the unit.
3. If at any time you feel faint, light-headed, or dizziness while operating this equipment, stop
exercising immediately and contact your physician. You should also stop exercising if you are
experiencing pain or any kind of discomfort.
4. Keep children and pets away from this equipment at all times.
5. Only one person should use this equipment at a time.
6. Make sure your equipment is correctly assembled before you use it. Be sure all the screws,
nuts, and bolts are tightened prior to use. Check the screws, nuts, and bolts are tight on a
weekly basis.
7. Do not operate this or any exercise equipment if it is damaged.
8. Wait 2 hours after eating before using this exercise equipment. If you get nauseous, stop
exercising as soon as you feel queasy.
9. This product should be placed on a flat surface when using. Amat or other covering material on
the ground is recommended. For indoor use only, do not use outdoors or near water.
10. Keep hands and feet away from any moving parts. Do not insert any objects into any openings
on the equipment.
11. Keep loose clothes, jewelry, limbs and long hair away from moving parts.
12. Children under the age of 12 should not use this fitness equipment.
13. Children from 12 to 18 should have adult supervision.
IMPORTANT SAFETY GUIDEILNES
4

Warning: It is highly recommended that you have assistance during the assembly of the strength
equipment.
1. Tools for assembly:
General tools you may need for the assembling this strength equipment:
Metric Allen Key Set
Metric Wrench Set and Adjustable Wrench
Flat Screwdrivers
Phillips Screwdrivers
Rubber Mallet
Silicone Spray Oil
2. Insert bolts into the frame as illustrated in the drawing of each of the steps.
3. Hand-tighten the bolts, nuts, and screw during assembly. Hand-tightening will allow for easily aligning
the parts during assembly. Tighten all the hardware once the entire unit has been completely
assembled.
4. It is highly recommended that a professional installer assembles the strength equipment. But, with the
proper assistance, the right tools, and strictly following the assembly steps, and given enough time;
the assembly of the unit can be achieved without professional help.
5. Thoroughly read each step before proceeding to assemble the parts of that step.
6. To aid in the assembly of the equipment, the hardware pack (bolts, nuts, washer…etc.) have been
presorted according to their corresponding steps. See the Hardware Pack page.
7. When the equipment is fully assembled check all the functions for correct operation. Consult the
manual if you experience any issues, or for further help please contact our service department. See
page 2.
ASSEMBLY PREPARATION
5

OVERVIEW DRAWING
6

Part #
Description
Q'ty
A
Upper Frame
1
B
Left J-Hook
1
C
Right J-Hook
1
D
Left Long Safety Catch
1
E
Right Long Safety Catch
1
F
Base Beam
2
G
Gusset Plate
4
H
Mounting Plate
2
I
Weight Plate Holder
2
J
Shaft
2
K
Landmine Attachment
1
L
U-Bracket
1
M
Rear Cross Bar
1
N
Upright Frame
2
8
Elastic Cord
2
9
Cable Ring
4
10
Long Rubber Pad
2
11
Short Rubber Pad
2
12
Knob
1
13
Bolt ￠12*M10*90
1
14
Safety Pin with Ring ￠8*87
2
15
Screw M6*10
12
32
Hexogen Head Bolt M10*75
18
33
Hexogen Head Bolt M10*20
2
34
Spring Washer D15.4 *D10.2*T2.6
2
35
Washer D30 *D10.5*T2.5
2
52
Washer D24 *D13*T2.5
12
67
Washer D20 *D10.5*T2.0
37
75
Nylon Lock Nut M10
19
138
Round End Cap
8
294
Spring Clip
2
485
Foot End Cap
4
PART LIST
7

Wrench 2 pcs
HARDWARE PACK
8

9
HARDWARE PACK
(12) Knob 1PC
(485) Foot End Cap 4 PCS
(294) Clip 2PCS

10
PRODUCT DRAWING

1A. Insert a Foot End Cap (485) into each side of the Base Frame (F).
2 - (485) Foot End Cap, see fig. A.
1B. Attach the Rear Cross Bar (M) and two Mounting Plate (H) to the Base
Frame (F) using:
4 - (32) Hexagon Head Bolt
10 - (67) Washer
4 - (75) Nylon Lock Nut
2 - (33) Hexagon Head Bolt
2 - (34) Spring Washer
Do not thoroughly tighten the hardware until instructed.
11
STEP 1

(32) Hexagon Head Bolt
4PCS
(67) Washer
10PCS
(75) Nylon Lock Nut
4PCS
Wrench
2 PCS
STEP 1
12
(33) Hexagon Head
Bolt 2PCS
(485) Foot End Cap
4PCS
(34) Spring Washer
2PCS
Fig A.

2A. Attach four Gusset Plate (G) to the Base Beams (F) by using:
4 - (32) Hexagon Head Bolt
8 - (67) Washer
4 - (75) Nylon Lock Nut
2B. Attach two Upright Frames (N) to the four Gusset Plate (G) by using:
4 - (32) Hexagon Head Bolt
8 - (67) Washer
4 - (75) Nylon Lock Nut
Note: attached one Upright Frames (N) to the Gusset Plate (G) firstly. Lift up a
little to make sure the holes on Upright Frames (N) align with Gusset Plate (G).
Tighten the Bolts (32), Washers (67), and Nuts (75) by wrench provided.
Repeat the process again to install the other Upright Frames (N).
Give the cage a shake so all the structure can settle and then
thoroughly tighten ALL the hardware.
STEP 2
13
Appearance upon completion of Step 2

STEP 2
Wrench
2 PCS
(32) Hexagon Head Bolt
8PCS
(67) Washer
16PCS
(75) Nylon Lock Nut
8PCS
14

3A. Attach the Upper Frame (A) onto both Upright Frames (N) by using:
4 - (32) Hexagon Head Bolt
8 - (67) Washer
4 - (75) Nylon Lock Nut
NOTE 1: The Upright Frames (N) have decals that say UP. The ends with the
UP decal should be attached to the Upper Frame (A).
NOTE 2: There are two height installation options for the Upright Frames (N).
Do not thoroughly tighten the hardware until instructed.
15
STEP 3
Appearance upon completion of Step 3

STEP 3
16
Wrench 2 PCS
81 inch
height
option
78 inch
height
option
(32) Hexagon Head Bolt
4PCS
(67) Washer
8PCS
(75) Nylon Lock Nut
4PCS

4A. Attach the Weight Plate Holder (I) onto the Upright Frame (N) by using:
2 - (32) Hexagon Head Bolt
2 - (67) Washer
2 - (75) Nylon Lock Nut
2 - (35) Washer
Give the cage a shake so all the structure can settle and then
thoroughly tighten ALL the hardware.
STEP 4
17

STEP 4
18
(32) Hexagon Head Bolt
2PCS
(67) Washer
2PCS
(75) Nylon Lock Nut
2PCS
Wrench
2 PCS
(35) Washer
2PCS