Flash Furniture HG-3WPB21-K04-K-BK-GG User manual

..................................................................................................................................................................................
Customer Service Email: [email protected] | Phone: [phone]
HG-3WPB21-T01-T-BK-GG /HG-3WPB21-F02-F-BK-GG /HG-3WPB21-Q03-Q-BK-GG / HG-3WPB21-K04-K-BK-GG
HG-3WPB21-T01-T-GY-GG / HG-3WPB21-F02-F-GY-GG /HG-3WPB21-Q03-Q-GY-GG / HG-3WPB21-K04-K-GY-GG
Thank you for your purchase!
PLATFORM BED FRAME
ASSEMBLY INSTRUCTIONS
Before You Begin:
Please indentify all component parts and hardware pieces required before you begin. Carefully remove
all of the components from the packaging and set aside for assembly. Assemble on a soft surface to
prevent scratching during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or
components may result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly Required.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where
included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The
tipping restraint is intended only as a safety measure, it is not a substitute for proper adult supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall Straps
suitable for the unit weight and wall materials (if not included) should be purchased and installed.
500
LBS 400
LBS
400
LBS
400
LBS
400
LBS
TWIN SIZE FULL SIZE QUEEN SIZE KING SIZE
250
LBS
250
LBS

Have a Question/Concern?
Qualityproducts andfirst-class customer service are the cornerstone of long-lasting
consumer relationships. We strive toward excellenceinallwe doandwant youtobe
completely satisfied with your purchase.
Please contact our exceptional Customer Experience Agents at the emailaddressor phone
number shown below to assist you with any product questionsorissues before requesting
a return.
We look forward to serving you in a friendly, efficientmannertoresolveanyissuesyoumay
have.
Customer Service Email: [email protected]
Customer Service Phone: [phone]
For warranty information, please visit www.belnick.com

2
KK
D
B
C
A
LMN
L
G
HG
I
F
M
N
L
I
1
3 4
LMN
L
1pc
I M
Siderails Screw
f 8*40
B
2pcs
J N
Headboard
Side Legs Middle Brace
C
1pc
K O
Headboard
Middle Leg Middle Cross Beam
D
1pc
L P
Footboard Middle Leg Middle Slat
Holders
E
F
G
HWashers
f 8
AHeadboard Components
PLATFORM BED FRAME
INSTRUCTION
STEP 1: Attach Headboard Side Legs
(Part B) and Headboard Middle Leg
(Part C) to Headboard (Part A) using
(6) Washers (Part L) and (6) 8*40
Screws (Part M). Tighten with Allen
Wrench (Part N)
STEP 2: Insert Bed Legs (Part K) into Footboard
(Part D) and turn clockwise to tighten.
STEP 3: Attach Middle Cross Beam (Part
G) to Middle Leg (Part H) using (2)
Washers (Part L) and (2) 8*40 Screws
(Part M). Tighten with Allen Wrench
(Part N)
STEP 4: Attach Middle Brace(Part
F) to Middle Brace Feet(PartI)
using (2) Washers (Part L)and (2)
8*40 Screws (Part M).Tighten with
Allen Wrench (PartN)
NOTE: Ensure
brackets face
outward withslots
point up.

MN
L
G
F
H
I
G
I
J
P
JO
5 6
7 8
9 10
E
E
E
E
E
E
E
E
STEP 5: Attach Middle Brace (Part F) to Middle
Cross Beam (Part G) using (1) Washer (Part L) and
(1) 8*40 Screw (Part M). Tighten with Allen Wrench
(Part N)
STEP 6A: Remove preassembled screws from middle leg. Attach Middle
Cross Beam (Part G) to Middle Headboard Legusingpreassembledscrews.
STEP 6B: Remove preassembled
screws from Footboard. Attach
Middle Brace to Footboard(PartD)
using preassembledscrews.
STEP 7:Remove remaining preassembled screws from Headboard
Side Legs and Footboard. Attach Siderails (Part E)toHeadboardand
Footboard using preassembled screws.
STEP 8: Loosen preassembled screws from Siderails(PartE).Insert
screws into the slots of the Middle Legsthentightenscrews.
STEP 9: Insert (28) Slats (Part J) into theleftandrightsidesof theMiddle
Slat Holders (Part P). Insert Slats into Outer SlatHolders(PartO).Push
down on slat holders to secure.
STEP 10: Ensure all screws and slats are secure.