Flash Furniture XU-DG-UH3048-UB19BTL-GG User manual

Thank you for your purchase!
Rectangular Outdoor Patio Dining Table
with Poly Resin Faux Wood Slats &
Umbrella Hole
ASSEMBLY INSTRUCTIONS
Before You Begin:
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the
components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching
during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or componenets
may result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly Required.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where
included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The
tipping restraint is intended only as a safety measure, it is not a substitute for proper adult supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall
Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed.

Have a Question/Concern?
Quality products and first-class customer service are the cornerstone of long
lasting consumer relationships. We strive toward excellence in all we do and
want you to be completely satisfied with your purchase.
Please contact our exceptional Customer Experience Agents at the email
address or phone number shown below to assist you with any product
questions or issues before requesting a return.
We look forward to serving you in a friendly, efficient manner to resolve any
issues you may have.
Our Warranty Statement








 














PARTS
STEP 1
STEP 1A: Lay table top (Part B)
on its top on a clean, soft surface.
From the inside of the Table Top
frame, attach the Table Legs (Part A)
to the Table Top using (10) M8*45
Bolts (Part C), (10) Q8 Washers (Part
F) and (10) Q8 Lock Washers.
Tighten all bolts with Allen Wrench
(Part E)
Table Leg
Table Leg
Allen Wrench
M8*45 Bolt
Allen Wrench
Allen Wrench
Q8 Washer
Q8 Lock
Washer
Table Top
CM8*45 Bolt
FQ8 Washer
G
Q8 Lock Washer
STEP 1B: Secure corners of
Table Top (Part B) to Left and
Right Table Legs (Part A)
using (4) M8*15 Bolts (Part D).
Tighten all bolts using Allen
Wrench (Part E)
M8*15 Bolt
STEP 2: Return table to the upright position
and ensure all bolts are securely fastened.

19 .3 Inch Umbrella Base
Thank you for your purchase!
ASSEMBLY INSTRUCTIONS
Before u Begin:
 


Caution:
 


Warning:
CHOKING HARD 
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE






Screw
Column
Adapters
Umbrella base
Adjustment Knob
Insert the correct adapter (Part E) for your umbrella
into the Column (Part C).
Turn the Umbrella Base (Part B) on its side and
insert the screw (Part A) into the underside.
Turn the Column (Part C) clockwise to tighten.
Column
3 Adapters
Umbrella Base
Screw
Place the Adjustment Knob (Part D) in the Column
(Part C) then turn clockwise to tighten.
Adjustment Knob
Column
Umbrella Base
To avoid injury, turn base on its side and roll to move

Thank you for your purchase!
9 FT Round Umbrella
ASSEMBLY INSTRUCTIONS
Before You Begin:
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of
the components from the packaging and set aside for assembly. Assemble on a soft surface to prevent
scratching during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or components
may result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly Required.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware
(where included) to help prevent the unit from tipping and causing accidental injury, instability, death or
damage. The tipping restraint is intended only as a safety measure, it is not a substitute for proper adult
supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall
Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed.

PARTS
A 1 PC
B 1 PC
C 1 PC
STEPS
.....................................................................................
DO NOT OPEN OR CLOSE
THE UMBRELLA WHEN
TILT ED
PRESS THE BUTTON TO
TILT THE UMBRELLA
POSITION
A
Umbrella Cap
Extension Pole
Umbrella