Flash Furniture NAN-NJ-HD10168-GG User manual

Customer ServiceEmail: [email protected] | Phone: [phone]
Thank you for your purchase!
Computer Desk
with Storage
NAN-NJ-HD10168-GG
ASSEMBLY INSTRUCTIONS
Before You Begin:
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the
components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching
during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or components may
result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly Required.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where
included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The
tipping restraint is intended only as a safety measure, it is not a substitute for proper adult supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall
Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed.
Online Assembly Instructions: http://ftp.flashfurniture.com/AssemblyInstructions/NAN-NJ-HD10168-GG.pdf

PARTS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
1PC
1PC
1PC
2PCS
1PC
1PC
1PC
1PC
1PC
1PC
1PC
1PC
1PC
1PC
15. 1PC
A
B
C
D
E
F
G
H
17PCS
17PCS
M6x35
2PCS
M6x12
2PCS
M3.5x14
8PCS
I
M4x18
2PCS
M5x50
18PCS
1PCS
M5x60
6PCS
15 Left
15 Right
16 Right
16 Left

3 PETS
2PETS
STEP 1
X2
X4
G
X2
E
15
X2
X2
AB
X10E
X4
A
Attach left drawer track (Part 15 Left) to left side panel
(Part 2) and right drawer track (Part 15 right) to right
side panel (Part 3) using M3.5x14 screws (Part G).
Ensure the wheel faces the front.
Attach left side panel (Part 3) and right
side panel (Part 2) to upper and lower
shelves (Part 4) using 8 screws (Part
E). Attach back panel (Part 6) to left
and right side panels using joint
connector nut (Part B) and dowels
(Part A). Insert 2 remaining screws
(Part E) on left and right side panels
and tighten.
Attach bottom panel (Part 5) to storage
unit using joint connector nuts (Part B)
and dowels (Part A). Insert screws (Part
E) into bottom front and back holes of
right side panel (Part 2)
5

6 PETS
5PETS
STEP 4
X2
E
X7
X7
AB
X2
C
X2
D
X4
H
X2
H
H
H
Attach rear stabilizing panel to the upper part of
the storage drawer unit using M5x50 screws
(Part E) and M5x60 screws (Part H)
Lay unit on its back and attach right metal frame foot (Part 9)
using M5x60 screws (Part H) and M6x12 bolts (Part D). Attach
left metal leg frame (Part 8) to rear stabilizing panel using 2
M5x60 screws (Part H)
Attach desktop (Part 1) to frame using joint connector
nuts (Part B) and dowels (Part A). Insert bolts (Part C)
through the underside of left metal frame and tighten.
1

9 PETS
8PETS
STEP 7
X4
X4
AB
X4
E
X2
X2
G16
X2
X1
I F
Attach left side drawer panel (Part 11) and right side drawer
panel (Part 10) to back panel (Part 13) using M5x50 screws
(Part E). Slide bottom panel (Part 14) into place and attach
front panel (Part 12) using joint connector nuts (Part B) and
dowels (Part A).
Turn drawer on its top and attach drawer glides
(Part 16 Right) and (Part 16 Left) using M3.5x14
screws (Part G).
16 Right
16 Left
Attach handle (Part I)
using M4x18 bolts (Part
F)
Insert drawer