Steelcase c:scape Parts list manual

#2 SQUARE
OR QUADREX
#2 SQUARE
OR QUADREX
PUTTY KNIFE
DRIVE BIT
Page 1 of 5
939500421 Rev A
c:scape™Mid Storage Outer Side, Top and Back Replacement
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
©2009 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.

1
2
#8-18 X 3/8" SCREW
OUTER SIDE
Fig. 1 Fig. 2
Side View
BOTTOM
FLANGE OF
OUTER SIDE
INNER SIDE
FLANGE
Page 2 of 5
939500421 Rev A
Removing Outer Side
1. Remove three (3) #8-18 x 3/8"
screws.
2. Gently pull the bottom flange of
the outer sides out past the inner
side flange (Fig.1) and then pull
toward the bottom of the unit to
disengage the inner side hooks
(Fig. 2). Remove sides.
3. Re-install the side by reversing
steps 1 and 2.

OR
#8-18 X 3/8" SCREW
2
3
TOP
Page 3 of 5
939500421 Rev A
Removing the Top
1. Remove both outer sides by
performing steps 1 and 2 on page 2.
2. Remove two (2) #8-18 x 3/8"
screws from each side of the
underside of the top.
3. Top slides off from side-to-side.
NOTE: Top will only slide one
direction, either left to right or right to
left. Try one, if that doesn't work,
slide it the other direction. Note
which way you slid it off.
4. Re-install the top by reversing
steps 1 thru 3. Make sure you slide
the top on the opposite direction
(reverse) of how it slid off and that all
top clips are properly engaged. (You
can check this by pulling up gently
along the length of the top - both front
and back. The top should not lift off).

3b
3a
BACK
#8-18 X 3/8" SCREW
Page 4 of 5
939500421 Rev A
Removing the Back
A: For All Units Except
Mid Storage Tall
Shared Slider Units
1. Remove both outer sides by
performing steps 1 and 2 on
page 2.
2. Remove the top by
performing steps 2 and 3 on
page 3.
NOTE: For a shared tall unit,
just remove the (1/2) back that
needs to be replaced.
3. Remove the #8-18 x 3/8"
screws (outer row of screws)
securing the back from the top
(3a) for each top. (Number of
screws will vary depending on
size and configuration.) Remove
the back (3b).
4. To re-install the back, reverse
steps 1 thru 3.

3a
3b
Side View
BACK
PUTTY
KNIFE
BACK FLANGE
Page 5 of 5
939500421 Rev A
Removing the Back
B: For Mid Storage Tall
Shared Slider Units
1. Remove both outer sides by
performing steps 1 and 2 on page 2.
2. Remove the top by performing
steps 2 and 3 on page 3.
NOTE: Just remove the (1/2) back
that needs to be replaced.
3. The back pops in and out. Gently
slide a putty knife in at the top and
use it to flex the back flange out of
the track (3a). Start at one end and
work across. The flange will "unzip".
Remove the back (3b).
NOTE: A wide putty knife may work
better.
4. To re-install the back, flex the
bottom so the tabs insert into the track.
Then carefully flex/feed the top into
its track until it pops/springs into
place.
NOTE: Align the center hook feature,
on the back, to the center slot in the
track.
4