Flexitron TAXITRONIC TX80 Urba User manual

INTERFACOM, S.A.U.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx 1
TX80 Urba / TX80 Urba One
USER’S MANUAL

INTERFACOM, S.A.U.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx 2
INDEX
1. TRIP SEQUENCE ........................................................................................................................................... 4
1.1. HIRED POSITION .................................................................................................................................. 4
1.2. ADDING EXTRAS IN HIRED................................................................................................................... 4
1.3. STOPPED POSITION ............................................................................................................................. 4
1.4. ENTERING EXTRAS IN STOPPED........................................................................................................... 5
1.5. ADDING THE EXTRAS TO THE FARE ..................................................................................................... 5
1.6. CANCELLATION OF MANUAL EXTRAS.................................................................................................. 5
1.7. END TRIP.............................................................................................................................................. 6
1.8. PRINT A TICKET .................................................................................................................................... 6
1.9. GOING BACK TO FOR HIRE................................................................................................................... 6
2. DISPLAY LAST TRIP DATA............................................................................................................................. 7
3. TOTALIZERS SEQUENCE ............................................................................................................................... 8
3.1. ACCUMULATIVE TOTALIZERS............................................................................................................... 8
3.2. DAILY TOTALIZERS ............................................................................................................................... 9
3.3. CLEARING DAILY TOTALS ..................................................................................................................... 9
4. FOR HIRE MENU ........................................................................................................................................ 10
4.1. SHIFT OPENING.................................................................................................................................. 10
4.1.1. TURN OFF................................................................................................................................... 11
5. ANCILLARY FUNCTIONS IN FOR HIRE......................................................................................................... 11
5.1. ROOFLIGHT ON/OFF .......................................................................................................................... 11
5.2. SETTINGS SEQUENCE......................................................................................................................... 11
5.2.1. DATE AND TIME VISUALIZATION ............................................................................................... 12
5.2.2. VOLUME..................................................................................................................................... 14
5.2.3. TEST SEQUENCE......................................................................................................................... 14
5.2.4. TAXIMETER CONTROL BLOCKS VISUALIZATION ........................................................................ 15
7.4.6. SKYGLASS CONTROL BLOCKS VISUALIZATION........................................................................... 19
7.4.7. LANGUAGE SETTINGS ................................................................................................................ 20
7.4.8. TEST LUMINOSO EXTERNO........................................................................................................ 21
6. ERROR MESSAGES ..................................................................................................................................... 22

INTERFACOM, S.A.U.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx 3
SWITCHING THE TAXIMETER ON.
Taximeter OFF.
Press the Okey to turn the Taximeter ON. If a password is required, the second point in the status
display will blink, waiting for the introduction of the code.
If no password is required, or once the correct code is entered, the taximeter goes to ON.

INTERFACOM, S.A.U.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx 4
1. TRIP SEQUENCE
1.1. HIRED POSITION
Press 1, 2, 3or 4key to start the right tariff.
For tariffs 5, 6, 7 and 8, first press the Δkey, and then press key 1, 2, 3or 4.
1.2. ADDING EXTRAS IN HIRED
By pressing key the text HIRED will start flashing.
Add the extras by pressing keys 1, 2, 3or 4. For extras 5, 6, 7 and 8, first press the Δkey, and then
press keys 1, 2, 3or 4.
To exit the extras sequence press key .
1.3. STOPPED POSITION
Press key to go to the Stopped position

INTERFACOM, S.A.U.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx 5
1.4. ENTERING EXTRAS IN STOPPED
By pressing key the text STOPPED will start flashing.
Add the extras by pressing keys 1, 2, 3or 4. For extras 5, 6, 7 and 8, press the Δkey, and then press
key 1, 2, 3or 4.
To exit the extras sequence press key .
1.5. ADDING THE EXTRAS TO THE FARE
Pressing +key adds the extras to the fare amount for 5 seconds. After this time, this amount will
break down again into fare and extras.
1.6. CANCELLATION OF MANUAL EXTRAS
Press the Δkey, and then press the key. The manual Extras will be erased. It is possible to add Extras
again if necessary. This function is optional, and may not be available to all markets.

INTERFACOM, S.A.U.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx 6
1.7. END TRIP
By pressing Okey . The status will start to blink for some seconds, until the taximeter switches to
FOR HIRE.
1.8. PRINT A TICKET
By pressing + while the status indication is blinking, the trip receipt will be printed. Copies of the
receipt can be printed by pressing + key again.
Press Oto go back to FOR HIRE.
1.9. GOING BACK TO FOR HIRE
The taximeter will go back to FOR HIRE automatically after a few seconds.

INTERFACOM, S.A.U.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx 7
2. DISPLAY LAST TRIP DATA
Only works when the car is stopped.
While in FOR HIRE, press the +key. The taximeter will show the following data successively:
- The Fare amount and the Extras
- The duration of the trip: Hours and minutes.
- The trip distance in kilometers.
Press the +key to print the receipt of the last trip.

INTERFACOM, S.A.U.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx 8
3. TOTALIZERS SEQUENCE
Only works when the car is stopped.
3.1. ACCUMULATIVE TOTALIZERS
By pressing key the first totalizer is shown.
Press +key to print the totalizers.
By pressing again key the next figures of the total will be displayed. The totalizers sequence can
be aborted at any moment by pressing the Okey.
After few seconds, if the key is not pressed, it switches to the next total, following the next list.
- 1 Nr. of trips
- 2 Fare amount
- 3 Extras amount
- 4 Total amount
- 5 Total distance (km)
- 6 Distance in Hired (km)
- 7 Distance in For Hire (km)
- 8 Time in hired (hours)
- 9 Time in ON (hours)
- A Nr. of daily totalizers cancellations

INTERFACOM, S.A.U.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx 9
3.2. DAILY TOTALIZERS
After the accumulated totalizers, the daily totalizers are showed by continuing pressing the key
according to the next list.
Press +key to print the totalizers.
By pressing again key the next figures of the total will be displayed. The totalizers sequence can
be aborted at any moment by pressing the key O.
- 1. Nr. of trips
- 2. Fare amount
- 3. Extras amount
- 4. Total amount
- 5. Total distance (km)
- 6. Distance in Hired (km)
- 7. Distance in For Hire (km)
- 8. Time in hired (hours)
- 9. Time in ON (hours)
3.3. CLEARING DAILY TOTALS
While the totalizer is showed, press key.
Enter the password with the 1, 2, 3y 4keys to change each of the four positions, and press the
key to confirm. Key 1 increases the thousands, key 2 increases the hundreds, key 3 increases the
tens and key 4 increases the units. If the code is correct, it will sound two short “beeps”. Otherwise, it
will sound a loud long “beep”.
Once the totals cancellation is done, the taximeter will go back to FOR HIRE.

INTERFACOM, S.A.U.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx 10
4. FOR HIRE MENU
In FOR HIRE, by pressing the Okey you access to the FOR HIRE MENU.
4.1. SHIFT OPENING
Press the key to put the taximeter in closed shift, then press the Okey to open shift.
Enter the Driver number changing the numbers using the 1, 2, 3y 4keys. Press the key.
Enter the Password number changing the numbers using the 1, 2, 3y 4keys. Press the key.

INTERFACOM, S.A.U.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx 11
If it is not a valid user/password pair, shift opening is rejected and the taximeter will return to closed
shift.
To close shift, press the Okey and then the key.
4.1.1. TURN OFF
If there is no interaction with the taximeter in the closed shift state, it turns OFF after a few seconds.
It turns to shift closed again pressing the Okey, or when the vehicle starts to move.
5. ANCILLARY FUNCTIONS IN FOR HIRE
5.1. ROOFLIGHT ON/OFF
By pressing Δkey and then +key the rooflight will toggle between ON and OFF. When the rooflight
is switched the icon will appear near the FOR HIRE.
5.2. SETTINGS SEQUENCE
Only available when the car is stopped.
By pressing Δkey twice, the different settings options are shown.
By pressing +key the printer makes a page feed.

INTERFACOM, S.A.U.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx 12
5.2.1. DATE AND TIME VISUALIZATION
The display of date and time is the first option shown.
By pressing key if shift control enabled, the remaining time and the available breaks will appear.
If the shift control is not enabled, it will directly show the time.
By pressing Okey it switches to FOR HIRE.
By pressing key again or after few seconds the time is displayed.
By pressing Okey it switches to FOR HIRE.
By pressing key again or after few seconds the date is displayed.

INTERFACOM, S.A.U.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx 13
By pressing Okey it switches to FOR HIRE.
By pressing key again or after few seconds the year is displayed.
By pressing Okey or after few seconds it switches to FOR HIRE.

INTERFACOM, S.A.U.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx 14
5.2.2. VOLUME
By pressing Δkey after light setting.
By pressing key to set the volume of the beep. The circular indicator shows the selected
intensity.
By pressing +changes the beep mode.
By pressing Okey it switches to FOR HIRE.
5.2.3. TEST SEQUENCE
By pressing Δkey after volume setting.
Press key to display the test sequence. (0,1, ...,9).

INTERFACOM, S.A.U.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx 15
By pressing Okey or after few seconds it switches to FOR HIRE.
5.2.4. TAXIMETER CONTROL BLOCKS VISUALIZATION
By pressing Δkey after test sequence.
By pressing Okey or after few seconds it switches to FOR HIRE.

INTERFACOM, S.A.U.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx 16
7.4.5.1. BLOCK 1 VISUALIZATION
C.1 Displays the current K Constant.
Press key for going to the next visualization or it goes automatically after few seconds:
- C.1 Current "K" constant
- C.2 Tariff serial number
- C.3 Tariff recording date (Y.MM.DD)
- C.4 Agent's code
- C.5 Tariff checksum
- C.6 Ticket identification control number.
- C.7 Pre-change tariff activation date
- C.8 Pre-change tariff checksum.
- C.9 Nr. of constant «K» changes
- C.A Nr. of tariff changes
- C.b Firmware TX80 Software Checksum
In case the shift control is set:
- C.C Shift duration on weekdays
- C.d Shift duration on weekends and holidays
- C.E Remaining time of the current shift
Press +key to print the control blocks.

INTERFACOM, S.A.U.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx 17
7.4.5.2. BLOCK 2 VISUALIZATION
L.1 Car License number.
Press key to go to the next visualization. The data displayed in block 2 are the following:
- L.1 Car License number
- L.2 Board serial number
- L.3 Manufacturing date (YYMMDD).
- L.6 Program version
Press +key to print the control blocks.
7.4.5.3. BLOCK 3 VISUALIZATION
I.1 State led tariff 1 indication
Press key for going to the next visualization or it goes automatically after few seconds.
The data displayed in the block 3 are the following:

INTERFACOM, S.A.U.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx 18
- I.1 State led tariff indication
- b.1 Flag drop
- M.1 Meters first drop
- S.1 Seconds firs drop
- d.1 Price per km
- H.1 Price per hour
- P.1 Price per km in stopped position
- E.1 Extras amount assigned to these tariff
Press +key to print the control blocks.
In case of more tariffs, the same data of block 3 is shown below for each of the remaining tariffs, that
is:
I.2 State led tariff 2 indication
Once the blocks visualization is finished, parameters of the versions are shown.

INTERFACOM, S.A.U.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx 19
- Pr Date of the update and taximeter version
- Pr User who updated it and checksum
- tF Date of the update and tariff
- C Date of the update and constant
- Po Date and time of power failures.
Once the blocks visualization is finished, the taximeter goes to for hire automatically.
The sequence can be aborted at any time by pressing the Okey.
7.4.6. SKYGLASS CONTROL BLOCKS VISUALIZATION
By pressing Δkey after taximeter control blocks visualization.
By pressing Okey or after few seconds it switches to FOR HIRE.

INTERFACOM, S.A.U.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx 20
7.4.6.1. BLOCKS VISUALIZATION
E.1 Serial number.
Press key to go to the next visualization, or automatically after few seconds:
- E.1 Skyglass serial number
- E.2 Software version
- E.3 Hardware version
- E.4 Checksum
Press +key to print the control blocks.
Once the blocks visualization is completed, the taximeter goes to for hire automatically.
The sequence can be aborted at any time by pressing the key O.
7.4.7. LANGUAGE SETTINGS
By pressing Δkey after Skyglass control blocks visualization.