Flonidan Gallus 2100 TCE User manual

GALLUS 2100 TCE
Installation Guide
Please look at our homepage www.flonidan.dk that you have the
newest version of the document.
Gallus 2100 TCE
Installation guide
M/04110XX-000/1
Rev. 260505
FLONIDAN ƔISLANDSVEJ 29 ƔDK-8700 HORSENS ƔTEL.: [phone]
WWW.FLONIDAN.DK

GALLUS 2100 TCE
Installation Guide
1.0 General
1.1 Introduction
Gallus 2100 TCE is an electronic, temperature compensated diaphragm meter,
available as mono or two pipes, from Qmax. 2.5 to 6 m3/h.
The meter is prepared for AMR - Automatic Meter Reading
Gallus 2100 will read out the accumulated consumption preferable as Nm3, Sm3,
kWh or MJ, as per choice depending on the customized configuration. Only one
reading is possible.
Display:
Alarm sign will be activated in case of error detected by the auto diagnostic system in the
electronics.
Page 2 of 4

GALLUS 2100 TCE
Installation Guide
Flow indicator
Flow indicator will flash when the meter is running.
At every cycle at the measuring unit (one cycle equals approx. 1.2 litres), the arrow will be
switched on or off. That means from switch on to switch off, or switch off to switch on
equals 1.2 litres.
The actual may easily be calculated by counting 10 switching on or off.
Note: count at on as well as off.
a) Start the stop watch at off
b) Count 1 at on
c) Count 2 at next off, and so on
d) At 10, stop the watch
Flow may be detected from the table,
or calculated from the formula:
Q = 41.13/T
Q = Flow [Sm3/h]
T = time for 10 on/off [sec.]
1.2 Mounting
Make sure that the installation is made stress less. No forces should be applied to the
meter from the pipe work.
The meter must be installed horizontally, in order to provide optimal measurement.
Avoid that the meter casing touches the wall, and use preferable isolated brackets for the
pipes, in order to prevent any vibrations or noise from the meter to be transferred to the
wall.
Important:
Gallus 2100 TCE is a high accuracy measuring instrument, that must be handled with
care. The meter should always be kept in horizontal position, in service and during
transportation.
10 on/off
[seconds]
Flow
[Sm3/h]
7 5.88
8 5.14
9 4.57
10 4.11
11 3.71
12 3.43
13 3.16
14 2.94
15 2.74
20 2.06
25 1.65
30 1.37
40 1.03
50 0.82
60 0.69
90 0.46
120 0.34
Page 3 of 4

GALLUS 2100 TCE
Installation Guide
Fig. 2. The interior of the Gallus 2100 TCE
When removing the cover, access is obtained to battery compartment and option board
compartment.
When installing option board, the following connections are available:
- Pulse output 1
- Pulse output 2
- Serial data output
For further details, please refer to Installation guide for Uniflo 1000 TCE
1.3 Disposal of the product after end of use.
This product is under the regulation of the EU directive 2002/95/EF, Waste
Electrical and Electronics Equipment (WEEE) and has to be handled
according to the directive, when it’s disposed of.
Revision history
Rev. Init Comment
26.05.2005 LBF Document created
20.11.2005 IGJ Disposal added
Flonidan DC A/S ƔIslandsvej 29 ƔDK-8700 Horsens
Tel. [phone] ƔFax [phone] ƔE-mail: [email protected]
Page 4 of 4