Flowserve Gestra GAV 56F User manual

Shut-Off Valve
GAV 56F
Original Installation Instructions
819237-01

Contents
Preface ...............................................................................................................................................3
Availability.............................................................................................................................................3
Text layout ............................................................................................................................................3
Safety..................................................................................................................................................3
Usage for the intended purpose..............................................................................................................3
Basic safety notes .................................................................................................................................4
Typographic features of warning notes....................................................................................................5
Typographic features of information on environmental & property damage ................................................5
Description .........................................................................................................................................5
Scope of supply and equipment specification ..........................................................................................5
Purpose and function.............................................................................................................................8
Storing and transporting the equipment...........................................................................................8
Storing the equipment ...........................................................................................................................9
Transporting the equipment ...................................................................................................................9
Mounting and connecting the equipment.........................................................................................9 
Preparing installation .............................................................................................................................9
Connecting the equipment ...................................................................................................................10
Retrofitting and adjusting a stroke limiter ..............................................................................................12
Operation ..........................................................................................................................................13
Activities during operation....................................................................................................................13
After operation .................................................................................................................................13
Changing the settings..........................................................................................................................14
Removing external dirt deposits............................................................................................................15
Maintaining the equipment...................................................................................................................15
Servicing the equipment and installing spare parts ................................................................................15
Troubleshooting ...............................................................................................................................16
Eliminating leaks .................................................................................................................................17
Putting the equipment out of operation ..........................................................................................18
Removing harmful substances..............................................................................................................18
Removing the equipment .....................................................................................................................19
Re-using equipment after storage.........................................................................................................19
Disposing of the equipment..................................................................................................................20
Technical data..................................................................................................................................21
Dimensions and weights ......................................................................................................................21
Flow characteristics.............................................................................................................................22
Pressure & temperature ratings............................................................................................................22
Manufacturer's Declaration.............................................................................................................23

3
Preface
This installation & operating manual will help you
use the shut-off valve GAV 56F safely and efficiently
for its intended purpose.
This valve will be called equipment in this
document.
This installation & operating manual is intended for
anyone commissioning, using, operating, servicing,
cleaning or disposing of this equipment and, in
particular, for professional after-sales service
technicians, qualified personnel and authorised and
trained staff.
All of these persons must read and understand the
content of this installation & operating manual.
Following the instructions given in this installation &
operating manual helps avoiding danger and
increases the reliability and service life of the
equipment. Please note that in addition to the
instructions given in this installation & operating
manual you must also observe all locally applicable
rules and regulations concerning the prevention of
accidents as well as approved safety guidelines for
good professional practice.
Availability
Keep this installation & operating manual together
with the plant documentation for future reference.
Make sure that this installation & operating manual
is available to the operator.
The installation & operating manual is part of the
equipment. Please hand over this installation &
operating manual when selling the equipment or
passing it on.
Text layout
Certain text elements of this installation & operating
manual feature a specific typographic design. You
can easily distinguish the following text elements:
Standard text
Cross-reference
Listing
Sub-items in listings
Steps for action.
Here you will find additional useful
information and tips serving to assist you
in using the equipment to its fullest
potential.
Safety
Usage for the intended purpose
The following shut-off valves are installed in pipes:
GAV 56F
The equipment is designed for shutting off neutral
gases, steam, vapours and liquids in pipelines.
Equipment of size DN 15 to DN 100 can also be
used for throttling the flowrate.
The equipment must only be used within the
allowable pressure and temperature limits and only
if the chemical and corrosive influences on the
equipment are taken into account.
Correct use includes compliance with the
instructions given in this installation & operating
manual, in particular obedience to all safety
instructions.
Any other use of the equipment is considered to be
improper.
Note that the equipment is also used incorrectly if
the materials of the equipment are not suitable for
the fluid.

4
Basic safety notes
Risk of severe injuries
The equipment is under pressure during
operation and may be hot. Before carrying out
any work on the equipment make sure that the
following requirements are met:
The pipes must be depressurized (0 bar).
The fluid must be completely removed from
the pipes and the equipment.
During work on the equipment the
installation must be switched off and
protected against unauthorised or
unintended activation.
The pipes and the equipment must have
cooled down to room temperature (approx.
20 °C).
If the equipment is used in contaminated areas
there is a risk of severe injuries or death caused
by harmful substances in or on the equipment.
Before working on the equipment make sure
that it is completely decontaminated. Always
wear the protective clothing prescribed for
contaminated areas when working on the
equipment.
The equipment must only be used with fluids
that do not attack the material and the gaskets
and sealings of the equipment. Otherwise leaks
may occur and hot or toxic fluid could escape.
The equipment and its component parts must
only be mounted or removed by qualified
personnel. A qualified person must be
acquainted with and experienced in the
following:
Making pipe connections.
Selecting suitable lifting gear and
understanding the rules for its safe use.
Working with dangerous (contaminated, hot
or pressurized) fluids.
Risk of minor injuries
Sharp edges on internals present the danger of
cuts to hands. Always wear industrial gloves
when servicing the equipment.
If the support of the equipment during
installation is insufficient the equipment might
fall down, thereby causing bruises or injuries.
Make sure the equipment is safely held in place
during installation and cannot fall down. Wear
protective safety footwear.
Risk of property damage or malfunctions
Malfunctions will occur if the equipment is
installed in a wrong position or with the flow
arrow pointing in the opposite direction of the
fluid flow. This may result in damage to the
equipment or the installation. Make sure that
the flow arrow on the equipment body matches
the indicated direction of the fluid flow in the
pipe.
If the material is unsuitable for the fluid,
increased wear may occur and fluid may
escape. Make sure that the material is suitable
for the fluid used in your installation.
The equipment may get damaged by pressure
impulses, even if the admissible nominal
pressure PN is not exceeded.
Make sure that the equipment is not subject to
pressure impulses or heavily pulsating flow.

5
Typographic features of warning
notes Description
DANGER
Notes with the heading DANGER warn
against imminent dangerous situations that
can lead to death or serious injuries.
Scope of supply and equipment
specification
Scope of supply
Our equipment is delivered packed and ready for
assembly.
WARNING
Notes with the heading WARNING warn
against possibly dangerous situations that
could lead to death or serious injuries.
CAUTION
Notes with the heading CAUTION warn
against dangerous situations that could
lead to minor or moderate injuries.
Typographic features of
information on environmental &
property damage
Attention!
This note warns against situations that
may lead to environmental and/or property
damage.

Equipment specification
3
4
6
7
8
11
12
13
10
9
1
2
5
6

No. Designation
1 Handwheel
2 Grease nipple and locking screw
3 Stem
4 Cover
5 Gasket
6 Body
7 Flow arrow
No. Designation
8 Name plate
9 Seat ring (up to DN 50)
10 Valve plug
11 Bellows
12 Gland packing
13 Stuffing box screw
Equipment of size DN 15 up to DN 100
feature a throttling plug.
Equipment fitted with a throttling plug
allows regulation of the flowrate.
Equipment of size DN 125 up to DN 150
feature a disk-type plug.
Equipment fitted with a this type of plug
can only be used for shutting off the
pipeline.
This installation manual shows equipment
with throttling plug.
A stroke limiter is available as optional extra.
End connections
The equipment is available with the following end
connections:
Flanges
Name plate
The following items are indicated on the name
plate:
Manufacturer
Type designation
CE marking
The CE marking depends on the
classification according to the Pressure
Equipment Directive (PED). Not all types of
equipment will therefore bear a CE
marking.
The following items are indicated on the equipment
body:
Nominal size
Pressure rating
Material
Batch code
Direction of flow
7

PED (Pressure Equipment Directive)
The equipment fulfills the requirements of the
Pressure Equipment Directive PED 97/23/EC and
can be used for the following fluids:
Fluids of group 1
Fluids of group 2
The following types of equipment are excluded from
the scope of the PED according to Article 3.3 and
must not bear a CE marking.
DN 15
DN 20
DN 25
The following types of equipment have a CE
marking on the name plate:
DN 32
DN 40
DN 50
DN 65
DN 80
DN 100
DN 125
DN 150
8
ATEX
Please observe the following notes if the
equipment is to be used in explosion-risk areas:
The equipment can be used in zones
(surrounding atmosphere acc. to Directive
1999/92/EC) 0, 1, 2, 20, 21 and 22 (ATEX
Directive 94/9/EC).
The equipment does not have its own potential
source of ignition and is therefore not subject to the
ATEX Directive 94/9/EC.
The equipment is not Ex marked.
Purpose and function
Purpose
The equipment is designed for shutting off
pipelines.
In addition, equipment DN 15 up to DN 100 can
also throttle the flowrate.
Function
The equipment is designed for shutting off
pipelines. For this purpose equipment types DN 125
and DN 150 are fitted with a disk-type plug.
Equipment of size DN 15 up to DN 100 can also
throttle the flowrate. For this purpose the equipment
is fitted with a throttling plug.
By turning the handwheel the stem is lifted or
lowered continuously. As a consequence, the plug
connected to the stem increases or decreases the
flow area.
You can lock the handwheel in the desired position.
The bellows seals off the valve stem.
Even if the bellows seal leaks, the stuffing box will
prevent any fluid from escaping. The stuffing-box
packing is slightly tightened when delivered.
Storing and transporting the
equipment
Attention!
Equipment can be damaged if stored or
transported improperly.
Close all openings with the sealing
plugs or covers supplied with the
equipment or use similar sealing
covers.
Protect the equipment against
moisture and corrosive atmospheres.
Please contact the manufacturer if the
specified transport and/or storage
requirements cannot be met.

Storing the equipment
Please observe the following items when storing
the equipment:
Do not store the equipment for more than 12
months.
Use the supplied sealing plugs or other suitable
seal caps in order to seal off all openings of the
equipment.
9
Protect the sealing surfaces and contact areas
against mechanical damage.
Protect the equipment and all components
against hard shocks and impacts.
Store the equipment only in closed rooms that
meet the following environmental conditions:
Air humidity below 50 %, not condensing
Indoor air: clean, salt-free and non-corrosive
Temperature 5–40 °C.
Make sure that all these requirements are
always met when storing the equipment.
Please contact the manufacturer if you cannot
comply with the recommended storage
conditions.
Transporting the equipment
Meet the requirements for storage also when
transporting the equipment.
Prior to transport seal off connections with
sealing plugs.
If you do not have the sealing plugs
supplied with the equipment use
appropriate seal caps to seal off the
connections.
For short distances (only a few metres) you can
transport the equipment unpacked.
When transporting the equipment over larger
distances use the original packaging.
If you do not have the original packaging use a
box that protects the equipment adequately
against corrosion and physical damage.
For a short period of time the equipment
may be transported even if the
temperature is below 0 °C, provided that
the equipment is completely empty and
dry.
Mounting and connecting the
equipment
Preparing installation
Take the equipment out of the transport
packaging.
Check the equipment for transport damage.
Contact the manufacturer if you detect any kind
of shipping damage.
When supplied by the factory, the connections may
be sealed off with sealing plugs.
Remove sealing plugs before mounting the
equipment.
Keep the sealing plugs and the packing for
further use.

10
DANGER
Personnel working on pipes are exposed to
safety risks and may suffer severe injuries,
poisoning or even loss of life.
Make sure that no hot or hazardous
fluid is in the equipment or the pipes.
Make sure that the pipes upstream
and downstream of the equipment are
depressurised.
Make sure that the installation is
switched off and protected against
unauthorised or unintended activation.
Make sure that the equipment and the
pipes have cooled down to room
temperatures.
Wear protective clothing that is
suitable for the fluid and, if necessary,
wear protective gear.
For more information on suitable safety clothing and
safety gear refer to the safety data sheet of the fluid
in question.
Drain pipes until they are empty.
Switch the installation off and protect it against
unauthorised or unintended re-activation.
Connecting the equipment
DANGER
Incorrectly connected equipment can
cause fatal accidents or severe injuries.
Make sure that only qualified skilled
personnel connect the equipment to
pipes.
Make sure that the flow arrow on the
equipment body matches the direction
of flow in the pipe.
Specialist personnel must be highly qualified and
fully experienced in making pipe connections for the
respective type of end connection.
Attention!
Equipment will be damaged if the end
connections are undersized.
Make sure that the connections are
strong and rigid enough to support the
weight of the equipment and to
withstand the forces that occur during
operation.
Make sure that the pipe system of the plant is
clean.
Make sure that the equipment is free from
foreign matter.
Attention!
Damage due to steam leakage may occur
if the equipment is installed with the
handwheel upside down.
Install the equipment with the
handwheel on top.
Furthermore, if the equipment is installed with the
handwheel upside down, dirt can accumulate in the
bellows.
When mounting the equipment make sure that
the handwheel is on top!
Make sure that the flow arrow matches the
direction of the fluid flow in the pipe.
Contact the manufacturer if you want to mount
the equipment in a different position of
installation.
Connect the equipment to the pipes.
Make sure that the equipment is safely mounted
and that all connections are made correctly.

11
CAUTION
Hot surfaces and heat radiation present
the risk of burns.
Wear protective gear that is suitable
for the temperatures generated in your
plant.
If you want to use the equipment in air-conditioning,
cooling or cryogenic installations, provide the
equipment with diffusion tight insulation.
Attention!
Malfunctions may occur if the equipment is
iced up.
Insulate the whole equipment.
If necessary, also insulate the
handwheel.
Use suitable insulating material.
The type of insulating material depends on the fluid
temperature.
For more information on suitable insulating
material please contact the manufacturer.
After installation ensure that the equipment is fully
functioning.
Fully open and close the valve several times.
After putting the equipment into operation make
sure that neither the equipment nor any
connections leak.
Should you encounter any leaks please proceed as
follows:
Attention!
Damage may occur if the equipment was
distorted during installation.
To open the equipment turn the
handwheel two turns anticlockwise.
Slowly fasten the cover bolts in
diagonally opposite pairs.
The tightening torque for the locking nuts for the
cover and the size of the bolts depend on the type
of equipment.
DN Tightening torque [Nm] Bolt
15–32 25 M10
40–50 35 M12
65 50 M12
80–150 110 M16
Tighten the nuts and bolts of the cover in
diagonally opposite pairs to the specified
torques.
After putting the equipment back into operation
make sure that neither the equipment nor any
connections leak.
Please contact the manufacturer if the
equipment and/or connections are untight.

Retrofitting and adjusting a stroke
limiter
CAUTION
Hot surfaces and heat radiation present
the risk of burns.
Wear protective gear that is suitable
for the temperatures generated in your
plant.
12
You can retrofit a stroke limiter.
The optional stroke limiter limits the stroke length, i.
e. the max. opening of the valve. Consequently, you
can limit the flowrate.
A commercial-grade hexagon bolt with nut serves
as stroke limiter. The size of the hexagon bolt and
nut depends on the equipment type.
The required hexagon bolt and nut are
commercially available.
Type Hexagon bolt
DN 15–80 M8 × 55
DN 100–125 M12 × 70
DN 150 M12 × 80
Procure a hexagon bolt and nut suitable for your
equipment type.
To fit the stroke limiter proceed as follows:
Screw the nut (16) onto the hexagon bolt (15).
Take the sealing plug (14) out of the handwheel
nut (17) (1.).
Screw the hexagon bolt onto the handwheel nut
(2.).
15
16
17
14
1.
2.

Adjusting the stroke limiter
The further you screw in the hexagon bolt, the more
the flowrate is reduced.
13
To restrict the stroke length screw the hexagon
bolt (15) in a clockwise direction.
To increase the stroke length screw the
hexagon bolt (15) in an anticlockwise direction.
15
To lock the stroke limiter in place, screw down
the nut until it hits the handwheel nut.
Operation
Activities during operation
CAUTION
Hot surfaces and heat radiation present
the risk of burns.
Wear protective gear that is suitable
for the temperatures generated in your
plant.
Do not work on the equipment while it is operating.
After operation
DANGER
If the equipment is used in contaminated
areas there is a risk of severe injuries or
death caused by harmful substances in or
on the equipment.
Only qualified personnel are allowed to
perform work on contaminated
equipment.
Always wear the protective clothing
prescribed for contaminated areas
when working on the equipment.
Make sure that the equipment is
completely decontaminated before
carrying out any service work.
Follow the pertinent instructions for
handling the hazardous substances in
question.
Attention!
Frost damage may occur when the
installation is shut down.
Drain the equipment if ambient
temperatures below 0 °C (frost) are to
be expected.

14
For work on the equipment you will need the
following tools:
Grease gun
DN15–DN32:
Spanner (US: wrench) A. F. 9 mm
Spanner (US: wrench) A. F. 10 mm
Spanner (US: wrench) A. F. 16 mm
Spanner (US: wrench) A. F. 32 mm
DN40–DN65:
Spanner (US: wrench) A. F. 9 mm
Spanner (US: wrench) A. F. 18 mm
Spanner (US: wrench) A. F. 22 mm
Spanner (US: wrench) A. F. 32 mm
DN80:
Spanner (US: wrench) A. F. 9 mm
Spanner (US: wrench) A. F. 22 mm
Spanner (US: wrench) A. F. 24 mm
Spanner (US: wrench) A. F. 32 mm
DN100–DN150:
Spanner (US: wrench) A. F. 9 mm
Spanner (US: wrench) A. F. 24 mm
Spanner (US: wrench) A. F. 30 mm
Spanner (US: wrench) A. F. 46 mm
Changing the settings
Equipment DN 15 up to DN 100 can also be used
to throttle the flowrate.
CAUTION
Hot surfaces and heat radiation present
the risk of burns.
Wear protective gear that is suitable
for the temperatures generated in your
plant.
Wear protective gloves that are suitable for the
fluid temperature.
Attention!
Equipment may get damaged if you use
any tools for changing settings.
Do not use a lever for operating the
handwheel.
To increase the flowrate turn the handwheel
anticlockwise (viewed from top).
To reduce the flowrate turn the handwheel
clockwise (viewed from top).
The closing direction is indicated by the
arrow and the word "ZU" (= Closed) on the
handwheel.
Loosen the locking screw (2) under the
handwheel.
Turn the handwheel (1) into the desired position.
Tighten the locking screw hand tight.
1
2
Check the adjustment
If the setting is not correct repeat the
adjustment procedure.

15
Apply a grease gun to the lubricating nipple in
the locking screw (2).
Removing external dirt deposits
To pump grease into the equipment squeeze the
grease gun handle once or twice.
CAUTION
Hot surfaces and heat radiation present
the risk of burns.
Wear protective gear that is suitable
for the temperatures generated in your
plant.
Remove any excess grease around the
lubricating nipple with a soft cloth.
2
To remove dirt deposits rinse the equipment
with fresh water and wipe it with a clean, lint-
free cloth.
To remove any persistent residues use a
cleaning agent that is suitable for the material
and carefully wipe the equipment with a clean,
lint-free cloth.
Maintaining the equipment
Servicing the equipment and
installing spare parts
CAUTION
Hot surfaces and heat radiation present
the risk of burns.
Wear protective gear that is suitable
for the temperatures generated in your
plant.
No spare parts are available for the equipment.
Replace a defective device with a new one.
Turn the handwheel every six months to both
stops.
You can increase the service life of the equipment
by applying a suitable lubricant to all moving parts.
A suitable lubricant is, for example, Klüber HEL46-
450 or any other grease with similar properties.

Troubleshooting
Problem Cause Remedy
Insufficient flowrate The equipment is not
completely open.
Completely open the equipment
The sealing plugs have not
been removed.
Remove the equipment. Take off the
sealing plugs. Mount the equipment.
Fluid escapes (equipment is
leaking).
The end connections are not
tight.
Insulate the connections.
A gasket on the body is
defective.
Replace the equipment with a new one.
Leakage occurs at the stem,
the bellows is damaged.
Re-tighten the stuffing box packing.
Replace the equipment with a new one.
The body has been damaged
by corrosion or erosion.
Check the resistance of the material for
the fluid used.
Use a device made from a material that
is suitable for the fluid used.
The equipment has been
damaged by frost.
Replace the equipment with a new one.
When shutting down the installation
make sure that all lines and the
equipment are completely drained.
The plug or seat is damaged. Replace the equipment with a new one.
The seat is leaking.
Excessive force is needed to
turn the handwheel.
The locking screw has been
tightened.
Loosen the locking screw.
The position of the stroke
limiter is fixed by a locknut.
Loosen the locknut of the stroke limiter.
The stem is insufficiently
lubricated.
Apply lubricant to the stem.
Limit stop has been reached. You can only turn the handwheel up to
the stop.
Turn the handwheel into the other
direction.
If faults occur that are not listed above or cannot
be corrected, please contact our Technical
Service or authorized agency in your country.
16

17
Eliminating leaks
If the bellows starts leaking tighten the stuffing box
screw to prevent fluid from escaping. Then replace
the whole equipment.
CAUTION
Hot surfaces and heat radiation present
the risk of burns.
Wear protective gear that is suitable
for the temperatures generated in your
plant.
Protective clothing must protect all body parts from
heat and prevent skin from coming into contact with
the fluid. This is particularly important for hands.
The tools required for the job depend on the type of
equipment.
DN A. F.
15-32 17 mm
40-80 22 mm
100-150 30 mm
Tighten the stuffing box screw (13) until no
more fluid escapes.
13
DANGER
Personnel working on pipes are exposed to
safety risks and may suffer severe injuries,
poisoning or even loss of life.
Make sure that no hot or hazardous
fluid is in the equipment or the pipes.
Make sure that the pipes upstream
and downstream of the equipment are
depressurised.
Make sure that the installation is
switched off and protected against
unauthorised or unintended activation.
Make sure that the equipment and the
pipes have cooled down to room
temperatures.
Wear protective clothing that is
suitable for the fluid and, if necessary,
wear protective gear.
For more information on suitable safety clothing and
safety gear refer to the safety data sheet of the fluid
in question.
Undo the end connections of the equipment.
Replace the equipment with a new one.

18
Putting the equipment out of
operation
Removing harmful substances
DANGER
If the equipment is used in contaminated
areas there is a risk of severe injuries or
death caused by harmful substances in or
on the equipment.
Only qualified personnel are allowed to
perform work on contaminated
equipment.
Always wear the protective clothing
prescribed for contaminated areas
when working on the equipment.
Make sure that the equipment is
completely decontaminated before
carrying out any service work.
Follow the pertinent instructions for
handling the hazardous substances in
question.
Qualified personnel must have extensive experience
with and a working knowledge of:
pertinent rules and regulations concerning
handling hazardous substances
special regulations for handling the hazardous
substances encountered on site
using the required personal protective
equipment (PPE) and clothing
Attention!
Environmental damage may be caused by
poisonous fluid residues.
Before disposing of the equipment
make sure that it is clean and free of
fluid residues.
For the disposal of all materials
observe the pertinent legal regulations
concerning waste disposal.
Remove all residues from the equipment.
For the disposal of all residues observe the
pertinent legal regulations concerning waste
disposal.

Removing the equipment
DANGER
Personnel working on pipes are exposed to
safety risks and may suffer severe injuries,
poisoning or even loss of life.
Make sure that no hot or hazardous
fluid is in the equipment or the pipes.
Make sure that the pipes upstream
and downstream of the equipment are
depressurised.
Make sure that the installation is
switched off and protected against
unauthorised or unintended activation.
Make sure that the equipment and the
pipes have cooled down to room
temperatures.
Wear protective clothing that is
suitable for the fluid and, if necessary,
wear protective gear.
19
For more information on suitable safety clothing and
safety gear refer to the safety data sheet of the fluid
in question.
CAUTION
Danger of bruising if the equipment falls
down.
When removing the equipment make
sure the it is safely held in place and
cannot fall down.
Suitable measures are for instance:
Equipment that is not too heavy may be
supported by a second person.
For heavy equipment use suitable lifting
equipment of sufficient strength.
Detach the end connections of the equipment
from the pipes.
Put the equipment onto a suitable base.
Store the equipment as described in section
"Storing the equipment" on page 9.
Re-using equipment after storage
Observe the following instructions if you want to
remove the equipment and use it again somewhere
else:
Make sure that the equipment is free of any
fluid residues.
Make sure that all connections are in good
condition and leak-free.
If necessary re-work welded connections in
order to ensure that they are in good working
condition.
Use the equipment only for its intended purpose
and the service conditions for which it was
specified.

20
Disposing of the equipment
Attention!
Environmental damage may be caused by
poisonous fluid residues.
Before disposing of the equipment
make sure that it is clean and free of
fluid residues.
For the disposal of all materials
observe the pertinent legal regulations
concerning waste disposal.
The equipment is made from the following
materials:
Component DIN / EN
Handwheel up to DN 80 Steel plate with epoxy
coating
Handwheel DN 100 up
to DN 150
Nodular cast iron
Stem 1.4021
Body, cover 1.0619+N
Packing rings Pure graphite
Stud bolts 1.7225
Hexagon nuts 1.7709
Flat gasket Pure graphite with
stainless steel insert
Bellows 1.4571
Valve plug 1.4021
Seat ring up to DN 50 1.4021
Seat ring from DN 65 1.4502, hard faced