Fluke 726 Configuration guide

Manual Supplement
© 2007-2008 Fluke Corporation. All rights reserved. Printed in the U.S.A. x
Manual Title: 726 Users Supplement Issue: 2
Print Date: September 2005 Issue Date: 3/08
Revision/Date: Page Count: 6
This supplement contains information necessary to ensure the accuracy of the
above manual. This manual is distributed as an electronic manual on the
following CD-ROM:
CD Title: 725/726
CD Rev. & Date: 4, 9/2005
CD PN: 1549615

726 Users Manual Supplement
3/07 1
Change #1
On page 2, replace the Pulse row with the following:
Pulse 1-100,000
Frequency Max 15 kHz
1-10,000
Frequency Range 2 CPM to 15 kHz
On page 12, Table 4, replace the Description for Number Lwith the following:
Cycles through:
ESlow repeating 0 % - 100 % - 0 % ramp
PConfigurable repeating 0 % - 100 % - 0% ramp
NConfigurable repeating 0 % - 100 % - 0 % ramp in 25 % steps
LUsed for the pulse train and totalizer functions.
On page 13, replace Figure 4 with the following:

Manual Supplement 726 Users
2 3/07
Low Battery
Symbol
Loop
Indicator
Memory Locations
for Calibrator Setups
Units
Display
Auto
Ramp
Mode
Indicator
HART Mode
Indicator
% Error
Indicators
Figure 4. Elements of a Typical Display

726 Users Manual Supplement
3/07 3
On page 14, under Configuration Menus, add the following under the last bullet:
•Step time
•Ramp time
On page 15, under Shut Down Mode, replace numbered steps with the following:
1. Press Cuntil SHUT DOWN appears on the display.
2. Use Xand Wto increase or decrease the time.
3. Use Yand Zto turn on and off.
4. Press Sto save the setting.
On page 16, under Hart®Resistor ON/OFF, replace step 2 with the following:
2. Use Vor Yand Zto toggle ON and OFF.
Add the following below the Note:
Step Time
Step Time sets the ramp step Ntime from 1 sec to 99 sec.
1. Press Cuntil STEP TIME appears on the display.
2. Use Xand Wto set the step time.
3. Press Sto save the setting.

Manual Supplement 726 Users
4 3/07
Ramp Time
Ramp Time sets the ramp Ptime from 5 sec to 99 sec.
1. Press Cuntil RAMP TIME appears on the display.
2. Use Xand Wto set the ramp time.
3. Press Sto save the setting.
On page 25, Table 6, add the following:
Cu10 10 ΩCopper 0.0042 Ω/°C -100 to 250
On page 42, under Auto Ramping the Output, replace the 2nd and 3rd bullets with the following:
•P0 % - 100 % - 0 % configurable time smooth ramp. Set ramp time using configuration
menu.
•N0 % - 100 % - 0 % Stair-step ramp in 25 % steps, pausing at each step. Set ramp
time using configuration menu. Steps are listed in Table 7.
On page 60, under Frequency Measurement, add the following to the bottom of the table:
Sensitivity: 1 V peak to peak minimum
Waveform: Squarewave

726 Users Manual Supplement
3/07 5
On page 62, change the Range entries for “Thermocouple in mV read” and “Thermocouple in
mV source”:
From:
-10 °C to 75 °C
To: -10 mV to 75 mV
On page 63, under the RTD Accuacy (Read and Source) (ITRS-90) table, replace the CU10 row
with the following:
Cu10 -100.0 250.00 1.8
On page 64, under Pulse Read and Pulse Source, replace the Frequency entry with the
following:
2 CPM to 15 kHz

Manual Supplement 726 Users
6 3/08
Change #2
On page 7, Table 2, add the following:
;Conforms to Australian C-Tick directives