Fluke 1736 Configuration guide

Manual Supplement
©2017-2019 Fluke Corporation. All rights reserved. x
Manual Title: 1736/1738 Users Supplement Issue: 4
Print Date: September 2015 Issue Date: 7/19
Revision/Date: 1, 7/17 Page Count: 10
This supplement contains information necessary to
ensure the accuracy of the above manual.

Manual Supplement 1736/1738 Users
1 7/19
Change #1, 381
On the Cover, add the ÉSymbol.
On page 4, add the following to the Symbols table:
É
Conforms to the Appliance Efficiency
Regulation (California Code of
Regulations, Title 20, Sections 1601
through 1608), for small battery
charging systems.

1736/1738 Users Manual Supplement
7/19 2
Change #2, 491
On page 6, replace Figure 1 with:
hcf069.eps
Figure 1. Adapter Installation

Manual Supplement 1736/1738 Users
3 7/19
Change #3, 594
On page 16, replace the Measurement Line Power Source
section with:
Measurement Line Power Source:
XWWarning
To prevent injury, do not touch the metal parts of one test lead
when the other is still connected to hazardous voltage.
WCaution
To prevent damage to the Product, make sure the measured voltage
does not exceed the input rating of the power supply.
1. Attach the power supply to the Logger.
2. Move the slide-cover on the power supply to access the safety
sockets.
3. Connect the short test leads (see Figure 7B & 7C) with the
power supply inputs. Make sure to use the non-stackable plugs.
The test leads are rated for measurement/overvoltage CAT III
1000 V and CAT IV 600 V.
4. Connect the test leads with the voltage measurement inputs:
•Connect A/L1 with one input of the power supply.
•Connect N with the second input of the power supply.
OR
•Connect A/L1 with one input of the power supply.
•Connect B/L2 with the second input of the power supply.
5. Use the short fan out of the Voltage Test Lead, 3-phase + N.
Plug the connector A/L1 into the socket A/L1 of the voltage
measurement inputs of the Logger. Repeat this with B/L2, C/L3
and N.

Manual Supplement 1736/1738 Users
4 7/19
•For measurement connection to the Logger (see Figure 7A):
Figure 7A: Measurement connection to the Logger

1736/1738 Users Manual Supplement
7/19 5
•To supply power to the Logger from installations with neutral
voltage (see Figure 7B):
Figure 7B: Measurement with neutral voltage and supplying
instrument power.
Note
You must locate and connect an alternate power source to the
instrument if the voltage to measure is <100 V or >500 V. Use
the set of 2 m test leads (item 8 in Figure 11) or the supplied
power cord.
6. Connect the voltage inputs to the test points.
The Logger automatically turns on and is ready to use in <30
seconds.

Manual Supplement 1736/1738 Users
6 7/19
•To supply power to the Logger from installations without neutral
voltage (see Figure 7C):
Figure 7C: Measurement without neutral voltage and supplying
instrument power.
Note
You must locate and connect an alternate power source to the
instrument if the voltage to measure is <100 V or >500 V. Use
the set of 2 m test leads (item 8 in Figure 11) or the supplied
power cord.
7. Connect the voltage inputs to the test points.
The Logger automatically turns on and is ready to use in <30
seconds.

1736/1738 Users Manual Supplement
7/19 7
Change #4, 491, 703
On page 5, replace Before You Start, with:
Your purchase includes these items. Carefully unpack and inspect
each of the items:
•Energy Logger
•Power Supply
•Voltage Test Lead, 3-phase + N
•2x Alligator Clips, Blue
•4x Alligator Clips, Black
•3x i173x-flex1500 Thin-Flexi Current Probe, 30.5 cm (12 in)
•Set of color-coded Wire Clips
•Mains Power Cable (see Table 2)
•Set of 2 test leads, stack and non-stackable, blue, 18 cm (7 in)
•Set of 2 test leads, non-stackable, blue, 2 m (79 in)
•DC Power Cable
•USB Cable A, Mini-USB
•Soft Storage Bag/Case
•Input Connector Decal (see Table 6)
•Documentation Info Pack (Quick Reference Card, Safety
Information)
•USB Flash Drive (includes Users Manual, Fluke Energy Analyze
Plus software, and Software Licenses)
Note
The power cord and input connector decal are
country specific and vary according to the order
destination.
The Energy Logger also includes these items in the
standard purchase list:
•WiFi to USB Adapter
•Magnet Hanger Kit
•Set of 4 Magnet Probes for 4 mm Banana Plugs
These items are available for the Energy Logger as optional
accessories.

Manual Supplement 1736/1738 Users
8 7/19
On page 9, replace the first paragraph and Figure 4, with:
Figure 4. Test Leads with Cable Markers
On page 10, replace Table 3 with:
Table 3. Accessories
Part ID Description
i17xx-flexi 1500 Thin-Flexi Current Probe (single) 1500 A, 30.5 cm (12 in.)
i17xx-flexi 1500/3PK Set of 3 Thin-Flexi Current Probes
i17xx-flexi 1500/4PK Set of 4 Thin-Flexi Current Probes
i17xx-flexi 3000 Thin-Flexi Current Probe (single) 3000 A, 61 cm (24 in.)
i17xx-flexi 3000/3PK Set of 3 Thin-Flexi Current Probes
i17xx-flexi 3000/4PK Set of 4 Thin-Flexi Current Probes
i17xx-flexi 6000 Thin-Flexi Current Probe (single) 6000 A, 90.5 cm (36 in.)
i17xx-flexi 6000/3PK Set of 3 Thin-Flexi Current Probes
i17xx-flexi 6000/4PK Set of 4 Thin-Flexi Current Probes
i17xx flexi extension
cable Thin-Flexi extension cable (single), 5m (197 in.)
i17xx flexi extension
cable/3PK Set of 3 Thin-Flexi extension cable

1736/1738 Users Manual Supplement
7/19 9
i17xx flexi extension
cable/4PK Set of 4 Thin-Flexi extension cable
C17xx Soft Case
Test Leads 0.18m 0.18 m (7 in.) Test Lead Set, blue
Test Leads 2m with
alligator clips 2.0 m (79 in.) Test Lead Set plus 2x alligator clips, blue
Voltage Test Lead 3-
phase+N, 2m (79 in.) 3PHVL-17xx Voltage Test Lead 3-phase + N, 2 m (79 in.)
Voltage Test Lead 3-
phase+N, 5m (197 in.) 3PHVL-17xx Voltage Test Lead 3-phase + N, 5 m (197 in.)
i40s-EL Current
Clamp 40 A (single) Current Clamp
i40s-EL/3PK Set of 3 Current Clamps, 40 A
i400S-EL 400 A (single) Current Clamp
i400S-EL/3PK Set of 3 Current Clamps, 400 A
Power Quality
Window PQ-400 Power Quality Window (PQ-400B / PQ-400)
17xx AUX Input
Adapter
Auxiliary Input Adapter for up to 2DC voltages (0 V to 10
V and 0 V to 1000 V)
Fused Test Probe Set Set of 4 Test Probes, three phase, AC285, 1x black, 3x
red
MP1-3R Magnet
Probe Set
Set of 4 Magnet Probes for 4 mm banana plugs, 1x black,
3x red
BP1730-Battery Pack BP1730-Battery Pack
Fluke-PQ-Marker Cable marker set 3 phase + N + PE
Fluke-1730-Hanger
Kit Hanger Kit
Fluke-
1732/UPGRADE for
EUR/US
Upgrade Kit for 1732 to 1734 (includes: Hanger, Magnet
Probes, Bluetooth Adapter, WiFi Adapter, and License
Key)
IEEE 519/Report Software License for IEEE 519 Reporting
FLK-WIFI/BLE
WiFi/BLE to USB Adapter (check with your sales
representative for availability)