Fluval Nano User manual

Instruction
Manual
Gebrauchsin-
formation
Mode
d’emploi
Gebruiksaan-
wijzing
Manual de
instrucciones

CONGRATULATIONS on your purchase of the Fluval Nano
Aquarium Filter. For a complete understanding of the filter’s operation
and capabilities, please read carefully and follow these instructions.
Be certain to read the SAFETY INSTRUCTIONS before using your filter.
IMPORTANT SAFETY
INSTRUCTIONS
WARNING - To guard against injury, basic safety precautions should be
observed, including the following:
1. READ AND FOLLOW ALL
SAFETY INSTRUCTIONS.
2. DANGER –To avoid possible electric shock, special care should be
taken since water is employed in the use of aquarium equipment.
For each of the following situations, do not attempt repairs
yourself; return the appliance to an authorized service facility for
service or discard the appliance.
A. If the appliance shows any sign of abnormal water leakage or
if RCD (or GFCI- Ground Fault Current Interrupter) switches off,
disconnect the power supply cord from mains and remove the
filter pump from water.
B. Carefully examine the appliance after installation. It should not
be plugged if there is water on parts not intended to be wet.
C. Do not operate any appliance if it has a damaged cord or plug,
or if it is malfunctioning or it is dropped or
damaged in any manner. The power cord
of this appliance cannot be replaced; if the
cord is damaged, the appliance should be
discarded. Never cut the cord.
D. To avoid the possibility of the appliance
plug or receptacle getting wet, position the
appliance to one side of a wall mounted
receptacle to prevent water from dripping
onto the receptacle or plug. A “drip loop”
(see illustration 1) should be arranged by the
user for the cord connecting appliance to a
receptacle. The “drip loop” is that part of the
cord below the level of the receptacle or the connector if an
extension cord is used, to prevent water travelling along the
cord and coming in contact with the receptacle. If the plug or
receptacle does get wet, DON’T unplug the cord. Disconnect
(illustration 1)
English

the fuse or circuit breaker that supplies power to the appliance.
Then unplug and examine for presence of water in receptacle.
3. WARNING - Close supervision is necessary when any appliance
is used by or near children. This appliance is not intended for use
by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use
of the appliance by a person responsible for their safety. Children
should be supervised to ensure that they do not play with
the appliance.
4. To avoid injury, do not touch moving parts or hot parts.
5. CAUTION – Always unplug or disconnect all appliances in the
aquarium from electricity supply before placing hands in water,
before putting on or taking off parts and whilst the equipment is
being installed, maintained or handled. When inserting or removing
the filter pump from the water, always pull out the main electricity
plug. Never yank cord to pull plug from outlet. Grasp the plug and
pull to disconnect. Always unplug an appliance from an outlet
when not in use.
6. This is an aquarium filter pump. Do not use this filter pump for
other than intended use (i.e.: do not use in swimming pools,
bathrooms, etc.). The use of attachments not recommended or sold
by the appliance manufacturer may cause an unsafe condition.
•Donotusethislterpumpinswimmingpoolsorothersituations
where people are immersed.
•Thislterpumpissuitableforuseinwatertemperaturesupto35°C.
•Donotusethislterpumpwithinammableordrinkableliquids.
7. This filter pump is suitable for Indoor Household Use Only.
8. Use only with fresh water. Not for use in salt water aquariums.
9. Do not install or store the appliance where it will be exposed to
the weather or to temperatures below freezing.
10. Make sure that the filter pump is securely installed before operating
it. Do not allow pump to run dry. The filter pump must be immersed
in water completely. This filter pump must never operate outside
of water.
11. If an extension cord is necessary, a cord with proper rating should
be used. A cord rated for less amperes or watts than the appliance
rating, may overheat. Care should be taken to arrange the cord so
that it will not be tripped over or pulled.
12. For the complete use and understanding of this product it is
recommended that this manual is thoroughly read and understood.
Failure to do so may result in damage to this product.
(illustration 1)

(For North America only)
13. This appliance has a polarized plug (one blade is wider than the
other). As a safety feature, this plug will fit in a polarized outlet only
one way. If the plug does not fit fully in the outlet, reverse the plug.
If it still does not fit, contact a qualified electrician. Never use with an
extension cord unless plug can be fully inserted. Do not attempt to
defeat this safety feature.
SAVE THESE INSTRUCTIONS
INSTALLATION and USE
WARNING: Disconnect the plug of all
aquarium appliances before placing your
hands into the aquarium water and / or
performing any maintenance of any kind.
Do not plug filter in until setup is complete
and aquarium is filled with water.
1. Unpack and identify all parts. Use the
parts diagram as a guide.
2. Rinse the filter case, Bio-Foam and
Fine Foam Pad in tap water.
3. Attachspraybarontoowcontrol
elbow. (A) Note: Adjust the water
owratebyrotatingtheowcontrol
knob.(B) The spray bar is multi-
directional so water output can be
directed as needed.
4. Install the assembled piece onto
the filter. (C)
5. Place filter on the right rear area of
the aquarium.
1. Spray Bar
2. Flow Control
Elbow
3. Motor housing
4. Magnetic
Impeller
5. Impeller Cover
6. Bio-Foam
7. Foam Cartridge
8. Fine Foam Pad
9. Filter Case
(A)
PARTS DIAGRAM
(B)
English

6. Press firmly to ensure the suction cups are holding it securely in place. (D)
WARNING: ALWAYS DISCONNECT APPLIANCES IN THE AQUARIUM FROM THE
ELECTRICAL SUPPLY BEFORE PLACING HANDS IN THE WATER, BEFORE PUTTING
ON OR TAKING OFF PARTS, AND WHENEVER THE FILTER EQUIPMENT IS BEING
INSTALLED, MAINTAINED OR HANDLED.
Following a routine maintenance schedule will result in a healthier aquarium
and extend the life of the filter. For best results, please follow our maintenance
schedule recommendations.
HOW TO CARE FOR THE FILTER MEDIA
IMPORTANT: Do not replace all filtration media at the same time. Alternate foam
changes so that some older ones remain in use. This ensures the re-seeding
of beneficial bacteria, so that colonies discarded with older media will be
replaced by vigorous new ones. To enhance bacterial action, pour a dose of
Nutrafin Cycle, a Biological Aquarium Supplement onto your filter media each
time you change it.
Do not use tap water as this will kill the beneficial bacteria in your foam.
NEVER use soap or detergents as these products could be harmful to the
inhabitants of your aquarium. Note: See Carbon Cartridge packaging for
replacement instructions.
How to Replace Filter Media
1. Unplug the filter and remove it from the installation.
2. Separate the filter case from the motor housing. (E)
3. Remove the Bio-Foam from the filter case and place in an empty bucket. (F)
(C) (D)
Media Purpose Maintenance Replacement
Bio-Foam
A456
Captures debris
and houses
nitrifying bacteria
Rinse monthly 3-6months
Fine Foam Pad
A457
Traps small
debris Rinse monthly 3-6months
Carbon
Cartridge A458
(available
separately)
Effectively
adsorbs odors,
discolorations
and impurities
N/A 2-4 weeks
(B)

4. Slide the foam cartridge out of
filter case, remove the Fine Foam
Pad from cartridge and place in an
empty bucket. (G)
5. Rinse Bio-Foam or Fine Foam Pad
using water taken from
the aquarium or replace
following the recommended
replacement schedule.
HOW TO CARE FOR THE
IMPELLER AND MOTOR
The impeller and impeller well (where
the impeller is located) should be
cleaned at least once a month, more
often if necessary. The impeller well
has an effective self-cleaning feature.
However, it is recommended that
you remove the motor and inspect
the impeller as part of your routine
maintenance. Keeping the impeller
clean lengthens its life and the life of
the motor.
Cleaning the Impeller:
1. Unplug the filter and remove it
from the installation.
2. Separate the filter case from the
motor housing. (E)
3. Remove impeller cover. (H)
4. Grasp the blades of the impeller
fan to pull out the impeller. (I)
5. Thoroughly clean the impeller and
the impeller well to remove slime,
dirt or debris. NEVER use soap or
detergents as these products
could be harmful to the
inhabitants of your aquarium.
6. Place the impeller back into the
impeller well. Replace the impeller
cover, and then re-attach the filter
case to the motor housing.
(E)
(F)
(G)
(H)
(I)
English

REPLACEMENT PARTS
To register your warranty on line or for more information on this and other
products go to www.hagen com.
FOR AUTHORIZED GUARANTEE REPAIR SERVICE:
For Authorized Warranty Service please return (well packaged and by registered
post) to the address below enclosing dated receipt and reason for return. If you
have any queries or comments about the operation of this product, please let us
try to help you before you return the product to your retailer. Most queries can
be handled promptly with a phone call. When you call (or write), please have all
relevant information such as model number, age of product, details of aquarium
set-up, as well as the nature of the problem.
CANADA: Hagen Industries, ConsumerRepair,3235Guénette,
MontréalQCH4S1N2
U.S.A.: Rolf C. Hagen (U.S.A.) Corp., 305ForbesBlvd,Manseld,MA.02048
UK: Rolf C. Hagen (UK) Ltd, Customer Service Department California Drive,
WhitwoodIndEst.,Castleford,WestYorkshireWF105QH
http://hagen-uk.custhelp.com
CALL US ON OUR TOLL-FREE NUMBER:
Canada only: 1-800-554-2436between9:00a.m.and4:30p.m.
Eastern Standard Time. Ask for Customer Service.
U.S. only: 1-800-724-2436between9:00a.m.and4:00p.m.
Eastern Standard Time. Ask for Customer Service.
U.K. only: HelplineNumber01977556622.Between9:00AMand5:00PM,
Monday to Friday (excluding Bank Holidays).
RECYCLING
This product bears the selective sorting symbol for waste
electrical and electronic equipment (WEEE). This means that
this product must be handled pursuant to European Directive
2002/96/ECinordertoberecycledordismantledtominimize
its impact on the environment. Check with your local
Environmental Agency for possible disposal instructions or
take to an official council registered refuse collection point.
Electronic products not included in the selective sorting
process are potentially dangerous for the environment and
human health due to the presence of hazardous substances.
(E)
(F)
(G)
(H)
Item Item Number
Impeller A-15002
Motor A-15000
2 YEAR WARRANTY
The Fluval Nano Aquarium Filter is guaranteed against defects in
material or workmanship under normal aquarium usage and service for
2 years. We offer a 2 year guarantee on all non-replaceable parts which
means that the filter will be repaired or replaced at the manufacturer’s
discretion, free of charge, when the complete pump is returned with
proof of purchase and postage paid. This warranty does not apply to
any filter that has been subjected to misuse, negligence, or tampering.
No liability is assumed with respect to loss or damage to livestock or
personal property irrespective of the cause thereof.