Fly Dragon LIGHT SKY TX0610 User manual

USER MANUAL
PROFESSIONAL SHOW LIGHTING
LED
TX0610
BEAM
www.lightsky.com.cn/www.lightsky-china.com
FLY DRAGON LIGHTING EQUIPMENT CO., LTD
AC100~240V 50/60H

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky. om. n
www.lightsky- hina. om
1
CONTENTS
1. General information 2
2. Safety instructions 3
3. Trait and s ill specifications 4
4. Operation panel 6
5. Dimensional drawings 6
6. Photometric data 7
7. Mounting and Installation 7
8. Power supply and Signal connection 9
9. Display menu 11
10. DMX traits 18
11. Circuit connecting diagram 22
12. Trouble dispose 23
13. Cleaning and Maintenance 24
14. Duty exonerative and Copyright protection .24

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky. om. n
www.lightsky- hina. om
2
1. GENERAL INFORMATION
INTRODUCTION: Congratulations, you have just pur hased one of the
most innovative and reliable LED fixtures on the market today. Our
ompany has been designed to perform reliably for years when the
guidelines in this booklet are followed. Please read and understand the
instru tions in this manual arefully and thoroughly before attempting to
operate this unit. These instru tions ontain important information
regarding safety during use and maintenan e.
UNPACKING: Thank you for pur hasing our ompany produ ts. Every
produ t has been thoroughly tested and has been shipped in perfe t
operating ondition. Carefully he k the shipping arton for damage that
may have o urred during shipping. If the arton appears to be damaged,
arefully inspe t your fixture for damage and be sure all a essories
ne essary to operate the fixture have arrived inta t. In the event damage
has been found or parts are missing, please onta t our ustomer support
team for further instru tions. Inside the box you should find: the fixture,
a DMX XLR able, a power able, and this user manual.
Please do not dis ard the shipping arton in the trash. Please re y le
whenever possible.
Notice: As part of our ongoing ommitment to ontinuous
produ ts update, ompany will keep the right to improve
this produ ts, the information in this menu may be
hanged in the future, the ompany reserve the right to
hange the data without any advises.

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky. om. n
www.lightsky- hina. om
3
2. SAFETY INSTRUCTIONS
●1. In order to ensure the light ould operate normally, the ambient
temperature ouldn't be higher than 38℃and no lower than- 2℃.
●2. Under normal ondition, the highest se tional surfa e temperature
may be up to 60 ℃.
●3.These proje tors are designed depends on the ele tri sho k
prote tion, the proje tor should be onne ted with the power supply
system whi h onne ted ground enough. The proje tor's ground
able should be onne ted with the ground able of the power
supply system as well. The ground mark of the light metal over
should be onne ting with the installation bri ked steadily.
●4. Don't use the power able when the insulation is damaged.
It must be the manufa turer or distributor or the professional person
to hange the damaged power able in order to avoid any
dangerous.
●5.Please he k the voltage, frequen y data of power supply system is
suitable for the mentioned on the proje tor. Please do avoid the
different voltage between them and burn the proje tor.
●6.Do not attempt to operate this fixture if the power ord has be ome
damaged or frayed.
●7.Never open this fixture while in use.
●8.Never look dire tly into the light sour e. You risk injury to your
retina, whi h may indu e blindness.
●9.Please be aware that damages aused by modifi ations to the devi e
are not subje t to warranty.
Notice: To guarantee proper and onsistent operation, it is
important to follow the guidelines in this manual. Our
ompany will not a ept responsibility for damages
resulting from the misuse of this fixture due to the
disregard of the information printed in this manual.

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky. om. n
www.lightsky- hina. om
4
3. PERFORMANCE TRAIT AND SKILL SPECIFICATIONS
◎Voltage：AC100~240V 50/60Hz.
◎Power：91W.
◎LED hip：10W，RGBW 4 in 1 LED hip.
◎LED QTY：6PCS.
◎LED life：50000H.
◎Lens degree：standard：1.5°.
◎Beam angle: Minimum 6°, Maximum 51°
◎Color: RGBW ma ro olor system.
◎Strobe:1-30 times/ se ond ele troni strobe and random strobe.
◎Dimmer ：65536 lass dimmer.
◎Pan/Tilt ：Pan ：540° times /1.5 se onds Tilt：180°/0.5 se onds.
◎Control Mode: DMX512, RDM, Stand-alone mode ,Voi e Control
mode , Mater-Slave mode , Wireless DMX512.
◎Channel: Standard Channel : 11 , Extend Channel : 17.
◎Display Menu:
1. 2.4 in hes TFT tou h s reen, Chinese and English two version
language.
2, Display board an re ord devi e’s using time , show devi e’s
temperature, hannel data and software version .
3, Edit the pro edure
◎Other feature :
1. Extend IP address fun tion , ea h IP address maximum an set 64
ID.

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky. om. n
www.lightsky- hina. om
5
2.Support DMX signal priority identifi ation, when lose the signal
it would be turn into Bla k , default s ene , Automati fun tion
et a ording to your set.
3.Remote ontrol fun tion: ontrol the pro edure, speed et
fun tion by the remote ontroller when the produ t under the
ondition without signal.
4.software upgrade : upgrade software by XRL able.
◎Outlooking: adopt ABS anti-fire plasti .
◎Carton size : 270×260×350MM.
◎N.W.: 3.8KG G.W.: 5.7KG
◎Light size:φ226×268MM

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky. om. n
www.lightsky- hina. om
6
4. OPERATION PANEL
5. DIMENSIONAL DRAWINGS

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky. om. n
www.lightsky- hina. om
7
6. PHOTOMETRIC DATA
7. MOUNTING AND INSTALLATION
Cautions:
For added prote tion mount the fixtures in areas outside walking
paths, seating areas, and away from areas were unauthorized personnel
might rea h the fixture. Before mounting the fixture to any surfa e, make
sure that the installation area an hold a minimum point load of 10 times
the devi e's weight. Fixture installation must always be se ured with a
se ondary safety atta hment, su h as an appropriate safety able. To
avoid injury, never stand dire tly below the devi e when mounting,
removing, or servi ing the fixture.
Mounting points:
Overhead mounting requires extensive experien e, in luding
amongst others al ulating working load limits, a fine knowledge of the
installation material being used, and periodi safety inspe tion of all
installation material and the fixture. If you la k these qualifi ations, do
not attempt the installation yourself. Improper installation an result in
bodily injury. Be sure to omplete all rigging and installation pro edures
before onne ting the main power ord to the appropriate wall outlet.

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky. om. n
www.lightsky- hina. om
8
Mounting
Our ompany is fully operational in any mounting position, hanging
upside-down, side mounted, or set on a flat level surfa e, et . Be sure this
fixture is kept at least 0.5m (about 1.6feet) away from any flammable
materials (de oration et .).
When lamp mounting; always use and install the supplied safety
able as an added safety measure to prevent a idental damage in the
event of a lamp failure. See the image below.

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky. om. n
www.lightsky- hina. om
9
8. POWER SUPPLY AND SIGNAL CONNECTION
1. Power supply
Use the professional plug to onne t the proje tor and main power
supply. Please pay attention to the voltage, frequen y the same as the
mentioned on the proje tor. Suggest ea h light has separately swit hed of
the power supply so that ould turn on or turn off ea h proje tor
desultorily.
2. Signal connection
Please use the round 3/5-pin XLR plugs &so kets offered by menu
fa ture to onne t the first proje tor's output to the se ond proje tor'
input and onne t the se ond proje tor's output to the third devi e's input.
And in the same way for the rest, eventually onne t the last devi e's
output, all the devi es are together as the following figure.
The devi es’ ontrol signal output or input by using the 3/5-pin XLR pug
and so ket. If need to long then the ommuni ation able, please make
sure the both side of 3/5-pin plug is one to one. (one to one, two to two,
three to three). Otherwise, the ommuni ation able will be interrupted.
The ommuni ate able is 2-pin shielded able 75Ω
Resistan e with ea h ore is at least a 0.5mm diameter. (Caution: All the
inside leading wire of 3/5-pin XLR plug ouldn't tou h ea h other or
plinth).
Re ommend to use the DMX signal terminator for the installation to
avoid the ele troni noise damage the digital ontrol signal. Simply
speaking, DMX terminator is an XLR onne tor with a 120Ω 1/2w

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky. om. n
www.lightsky- hina. om
10
resistor onne ted a ross pin 2 and 3.Whi h is then plugged into the
output so ket on the last proje tor in the hain. Refer to the onne tion as
above:(Pi ture ).We suggest using the DMX signal distributor when the
distan e of the lights over 15meter,In ase of effe t the light
ommuni ation be ause of the signal feeble.
3. Light power connection:
the items an't be more than 6p s under series onne tion.
After doing the above operation and making sure all the devi es had
been installed with natural operate, press the power swit h to he k
whether everything is working normally.

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky. om. n
www.lightsky- hina. om
11
9. DISPLAY MENU
Ⅰ Menu Ⅱ Menu Ⅲ Menu Remark
SETTING
DMX Address 001-512
Fixture ID 000-064
Channel mode Standard 11CH） Default
Extended 17CH）
DMX input
mode
Wired input Default
Wireless input
Reset wireless
DMX function
Hold
Black
D.scene
Program 1
Program 2
Program 3
Program 4
Program 5
Program 6
Program 7
Program 8
Slave-Master Slave mode
Master mode
Music
control
Close
Open
Exit

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky. om. n
www.lightsky- hina. om
12
Ⅰ Menu Ⅱ Menu Ⅲ Menu Remark
INFO
Fixture
times
Power on time ****H
Lamp on time ****H
Fixture
temperatures LAMP_TEM ***℃
RDM UID 888：********
DMX live
1. Dimmer 0-255
2. Dimmer fine 0-255
. Shutter 0-255
4. Red 0-255
5. Green 0-255
6. Blue 0-255
7. White 0-255
8. Macro colour 0-255
9. Pan 0-255
10. Pan fine 0-255
11. Tilt 0-255
12. Tilt fine 0-255
1 .Rota. lens 0-255
14. Rota.Sp 0-255
15. Fixture contro 0-255
16.Calibration 0-255
17.Slave ID 0-255
Version info LED_XY_SOFT:V*.**
LED_DPY_SOFT:V*.**
Exit

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky. om. n
www.lightsky- hina. om
13
Ⅰ Menu Ⅱ Menu Ⅲ Menu Ⅳ Menu Remark
PERSON
Pan/Tilt
P/T swap OFF Default
ON
Pan invert OFF Default
ON
Tilt invert OFF Default
ON
Exit
DMX
reset
ON Default
OFF
Reset System reset
Exit
Qui k
losedown
Open
Close
P/T angle
limit
Close
Open
Program
on/off
Close
Open
Set p/t
angle
Pan start
Pan end
Tilt start
Tilt end
Exit

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky. om. n
www.lightsky- hina. om
14
Ⅰ Menu Ⅱ Menu Ⅲ Menu Ⅳ Menu Remark
PERSON Display
Display
language
English(英文)
Default
Chinese(中文)
Display sleep
Light always
2 minutes Default
4 minutes
6 minutes
Display
intensity 10-100
Default
:50
Display rotation Normal
Default
Rotate 180
TFT alibration
Exit
Exit

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky. om. n
www.lightsky- hina. om
15
Ⅰ Menu Ⅱ Menu Ⅲ Menu Remark
MANUAL
1. Dimmer 0-255
2. Dimmer fin 0-255
3. Shutter 0-255
4. Red 0-255
5.Green 0-255
6. Blue 0-255
7. White 0-255
8.Ma ro olo 0-255
9. Pan 0-255
10. Pan fine 0-255
11. Tilt 0-255
12. Tilt fine 0-255
13.Rota.lens 0-255
14. Rota.Sp 0-255
15. Fixture 0-255
16. Calibrati 0-255
17. Slave ID 0-255
Exit

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky. om. n
www.lightsky- hina. om
16
Ⅰ Menu Ⅱ Menu Ⅲ Menu ⅣMenu
PROGRAM Edit
program
Edit program 1
S ene 0-100
1.Dimmer 0-255
2.Dimmer fin 0-255
3.Shutter 0-255
4.Red 0-255
5.Green 0-255
6.Blue 0-255
7.White 0-255
8.Ma ro olo 0-255
9.Pan 0-255
10.Pan fine 0-255
11.Tilt 0-255
12.Tilt fine 0-255
13.Rota.lens 0-255
14.Rota.Sp 0-255
15.Fixture 0-255
16.Calibrati 0-255
17.Slave ID 0-255
Save s ene
Exit
Edit program 2 Same as Edit program1
Edit program 3 Same as Edit program1
Edit program 4 Same as Edit program1
Edit program 5 Same as Edit program1
Edit program 6 Same as Edit program1
Edit program 7 Same as Edit program1
Edit program 8 Same as Edit program1
Exit

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky. om. n
www.lightsky- hina. om
17
Ⅰ Menu Ⅱ Menu Ⅲ Menu ⅣMenu
PROGRAM
Set
program
Set program 1
Start step 0-100
End step 0-100
Step time0-255
Save
Exit
Set program 2 Same as Set program 1
Set program 3 Same as Set program 1
Set program 4 Same as Set program 1
Set program 5 Same as Set program 1
Set program 6 Same as Set program 1
Set program 7 Same as Set program 1
Set program 8 Same as Set program 1
Exit
Run Running program.
Fixed s ene S ene 001-100
Exit
SERVICE
Error list
Adjust Pan ±5.00%
Tilt ±5.00%
Rota.lens ±5.00%
Exit
Fa tory Default ****
Adjust default ****
Time lean ****
Developer ****
Ma hine sel. ****
Exit
Updata ****
Exit

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky. om. n
www.lightsky- hina. om
18
10、DMX TRAITS
Channel DMX
values % Effe t
1. Dimmer 0-255 0-100
2. Dimmer fine 0-255 0-100
3. Shutter
0-9 0-3 Unused range
10-49 4-19 Light→dark，slow→fast
50-89 20-34 Dark→light，slow→fast
90-119 35-46 Dark→light→dark， slow→fast
120-179 47-70 Random fast→slow strobe
180-249 71-98 In-phase, slow→fast
250-255 99-100 Unused range
4. Red 0-255 0-100
5. Green 0-255 0-100
6. Blue 0-255 0-100
7. White 0-255 0-100
8. Ma ro
olour
0-1 0-1 Unused range
2-254 1-99 Shadow
255 100 Unused range
9. Pan 0-255 0-100
10. Pan fine 0-255 0-100
11. Tilt 0-255 0-100
12. Tilt fine 0-255 0-100
13. Rota.lens
0-127 0-49
128-135 50-52
136-231 53-90
232-255 91-100

LIGHT SKY FLY DRAGON LIGHTING EQUIPMENT CO.,LTD
www.lightsky. om. n
www.lightsky- hina. om
19
Channel DMX
values % Effe t
14. Rota.Sp 0-255 0-100
15. Fixture
control
0-9 0-3 Unused range
10-14 4-5 Complete reset
15-19 5-7 Open
20-24 7-9 Close
25-29 10-11 Qui k open
30-34 12-13 Qui k lose
35-239 14-93 Unused range
240-244 94-95 Pan
245-249 96-97 Tilt
250-255 98-100 Unused range
16.
Calibration 0-255 0-100
17. Slave ID
0-2 0
All IDs are effi ient lighting its
own ID to 0, the hannel set to
any value is valid
3-5 1-2 ID:1 effe tive
6-8 2-3 ID:2 effe tive
... ...
192-194 75-76 ID:64 effe tive
195-197 76-77 ID is(2*n)+1 effe tive,(n=0-31)
1、3、5、7、9…63
198-200 77-78 ID is(2*n)+2 effe tive,(n=0-31)
2、4、6、8、10…64
201-203 78-79 ID is(3*n)+1 effe tive,(n=0-21)
1、4、7、10、13…64