FLY XENIT SUPER User manual

VERSION 1.0 – 05/13
© Copyright by FLY Products s.r.l.
Via Perù n. 30
63013 GROTTAMMARE (AP) - ITALY
tel./fax [phone]
www.flyproducts.com - [email protected]
XENIT SUPER
OWNER’S MANUAL

XENIT SUPER OWNER’S MANUAL ____ ___ VER. 1.1
___________________________________________________________________________
© Copyright FLY Products s.r.l. Page
2
Index
Chapter Description
1.0
XENIT SUPER FEATURES
2.0
FRAME ASSEMBLY
3.0
EMERGENCY PARACHUTE
4.0
PROP MOUNTING
5.0
STARTING AND STOPPING ENGINE
6.0
ADJUSTING VERSION TANDEM OR MONO
7.0
A-ASSIST SYSTEM

XENIT SUPER OWNER’S MANUAL ____ ___ VER. 1.1
___________________________________________________________________________
© Copyright FLY Products s.r.l. Page
3
(1.0) XENIT SUPER FEATURES
•Easy assembly and disassembly
•Electric Starter
•Power Ignition
•Reduction drive
Dimensions

XENIT SUPER OWNER’S MANUAL ____ ___ VER. 1.1
___________________________________________________________________________
© Copyright FLY Products s.r.l. Page
4
(2.0) Frame assembly
Frame assembly and disassembly is very fast and easy.
The outer frame consists of four parts, and they are held together by the velcro straps.
For an easy and correct assembly proceed in the following order:

XENIT SUPER OWNER’S MANUAL ____ ___ VER. 1.1
___________________________________________________________________________
© Copyright FLY Products s.r.l. Page
5

XENIT SUPER OWNER’S MANUAL ____ ___ VER. 1.1
___________________________________________________________________________
© Copyright FLY Products s.r.l. Page
6

XENIT SUPER OWNER’S MANUAL ____ ___ VER. 1.1
___________________________________________________________________________
© Copyright FLY Products s.r.l. Page
7
(3.0) Emergency parachute
A reserve parachute can be attached to the XENIT SUPER and is highly recommended for obvious
security reasons. The reserve parachute is inserted under the harness of the pilot.
Assembly procedure of the emergency system:
Insert the emergency in the
pocket
Using a string to close the bag
Attach the handle
Side view after complete closure
Pass the straps behind the harness
Attach the straps to carabiner
where the glider is attached

XENIT SUPER OWNER’S MANUAL ____ ___ VER. 1.1
___________________________________________________________________________
© Copyright FLY Products s.r.l. Page
8
(4.0) Prop mounting
Mounting the prop is quick and easy.
Place the rear prop flange on the rear side of the prop.
Insert the six (6) prop bolts through the rear prop flange and
prop.
The correct torque to use is 28 Nm
A more practical “field method” of torquing is to tighten the
bolts snuggly and evenly, but not enough to begin to crush the
wood of the prop.
Mounting the prop, the red arrow indicate the direction of
propeller rotation.
(5.0) Starting and stopping engine
Stopping the engine
Before of proceed it's better to learn the function of the handgrip:

XENIT SUPER OWNER’S MANUAL ____ ___ VER. 1.1
___________________________________________________________________________
© Copyright FLY Products s.r.l. Page
9
A– STOP” button
B– Cruise control setup
C– Throttle lever
Since it’s important to know how to stop the engine once it’s started, let’s cover “Stopping the Engine”
first. To stop the engine, simply depress the “STOP” button A and hold it until the engine comes to a
complete stop.
Starting the engine

XENIT SUPER OWNER’S MANUAL ____ ___ VER. 1.1
___________________________________________________________________________
© Copyright FLY Products s.r.l. Page
10
Pump the fuel until the carburator float is
full.
Choke level to be used for the first start at cool
engine.
(6.0) Adjustments version tandem or mono