Focal Point LEXINGTON EF655SLB-E Assembly Instructions

I STALLATIO & USER I STRUCTIO S
MODELS COVERED BY THESE I STRUCTIO S
EF655SLB-E
LEXI GTO LED ELECTRIC FIRE
Focal Point Fires plc.
Christchurch, Dorset BH23 2BT
Tel: [phone]
Fax: [phone]
www.focalpointfires.co.uk
e : [e-mail]
LED ELECTRIC FIRE
1
Revision C - 06/19
GB IE
MODEL SHOW : LEXI GTO LED ELECTRIC FIRE
All instructions must be handed to the user
for safekeeping.
Please note : Except where otherwise stated, all
rights, including copyright in the text, images
and layout of this booklet is owned by Focal
Point Fires plc. You are not permitted to copy
or adapt any of the content without the prior
written permission of Focal Point Fires plc.
©2019 Focal Point Fires plc.
This product is only suitable for well insulated spaces or occasional use.

1.0 PRELIMI ARY OTES
I S TA L L AT I O & U S E R I S T R U C T I O S
2
GB IE
Section Contents Page o.
1.0 Preliminary otes 2
2.0 Installation Requirements 3
3.0 Appliance Data 3
4.0 Unpacking the Appliance 4
5.0 Component Checklist 4
6.0 Site Requirements 4
7.0 Clearances To Combustibles Materials 5
Section Contents Page o.
8.0 Installing the Appliance 5
9.0 Operating the Appliance 6
10.0 Safety Cut-Out System 8
11.0 Cleaning and Maintenance 9
12.0 Servicing 9
13.0 Guarantee - Terms and Conditions 10
IMPORTA T - THESE I STRUCTIO S SHOULD BE READ CAREFULLY
A D RETAI ED FOR FUTURE REFERE CE.
The appliance is designed for indoor use, and can be simply floor mounted in the
majority of floor positions anticipated. It can be located in any household room, with
the exception of bathrooms. Read all of the instructions before commencing installa-
tion. Retain for future reference and pass on as necessary to subsequent owners of the
appliance.
• DO OT use this appliance immediately above a fixed socket outlet.
• DO OT use this appliance in an open flue.
When using this electrical appliance, basic precautions should be followed to reduce the risk
of fire, electric shock and injury to person, including the following:
• This heater must be used on an AC supply only and the voltage marked on the heater’s
rating label must correspond to the supply voltage.
• DO OT switch the appliance on until it is properly installed as described in this
manual.
• This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children without supervision.
• Children of less than 3 years should be kept away unless continuously supervised.
Children aged from 3 years and less than 8 years shall only switch on/off the appliance pro-
vided that it has been placed or installed in its intended normal operating position and they
have been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children aged from 3 years and less than 8 years shall not
plug in, regulate and clean the appliance or perform user maintenance.
• CAUTIO : Some parts of this product can become very hot and cause burns.
Particular attention has to be given where children and vulnerable people are present.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
• The heater must not be located immediately above a socket-outlet.
• DO OT use this heater in the immediate surroundings of a bath, a shower or a swim-
ming pool, or other area where water/moisture could present a hazard.
• WAR I G: In order to avoid overheating, do not cover the heater.
• DO OT use this heater with a separate remote-control system or any other device
that switches the heater on automatically, since a fire risk exists if the heater is covered or
positioned incorrectly.
• CAUTIO : In order to avoid a hazard due to inadvertent resetting of the thermal
cutout, this appliance must not be supplied through an external switching device, such as a
©2019 Focal Point Fires plc.

3
• DO OT run the mains cable under carpets, rugs etc.
• DO OT cover or obstruct the heater in any way. Overheating will result if it is acci-
dentally covered.
• Never immerse the product in water or any other liquids.
• DO OT use the appliance outdoors.
• Before cleaning the appliance, ensure it is unplugged from the power and that it is com-
pletely cool.
• DO OT clean the appliance with abrasive chemicals.
• Never use accessories that are not recommended or supplied by the manufacturer. It
could cause danger to the user or damage to the appliance.
• DO OT insert or allow foreign objects to enter the inlet or outlet vents as this may
result in electric shock, fire or damage to the appliance.
• DO OT install the fire using an extension cord.
• Unplug from the mains supply if the appliance is not to be used for long periods.
• This product is only suitable for well insulated spaces or occasional use.
timer, or connected to a circuit that is regularly switched on and off by the utility.
• Keep furniture, curtains and other fabric material away from the appliance.
• DO OT leave the appliance unattended during use.
• From time to time, check the cord for damage. Never use the appliance if the cord or any
part of the appliance shows signs of damage.
1.0 PRELIMI ARY OTES - CO TI UED GB IE
3.0 APPLIA CE DATA
Weight (kg): 12 kg
Voltage (Volts): 220-240V a.c. 50Hz
Rated Power 1800W
Supply Plug: BS 1363, 13A Fused
Supply Cord: 1.8 Metres
Location: Indoor Use
LED Display: 7 Watts
2.0 I STALLATIO REQUIREME TS
©2019 Focal Point Fires plc.
The appliance is supplied with a pre-wired three pin plug (13 Amp fuse rated) and 1.8 metres of electrical cable. It is therefore
necessary for a suitable electrical socket to be located within this distance and be easily accessible. This appliance is designed to
be wall hung, using the wall fixtures/fixings provided. DO NOT recess any part of appliance into the wall. This appliance is suit-
able for installation in static holiday/park homes.
All Models EF655SLB-E
Item Symbol Value Unit Item Unit
Heat output Types of heat input, for electric storage local
space heaters only
Nominal
heat output
Pnom 1.8 KW Manual heat charge control with
integrated thermostat
N/A
Minimum heat
output
(indicative)
Pmin 0.9 KW Manual heat charge control with
room and/or outdoor temperature
feedback
N/A
Maximum
continuous heat
output
Pmax, c 1.8 KW Electronic heat charge control with
room and/or outdoor temperature
feedback
N/A
Auxiliary electricity consumption Fan assisted heat output N/A
At nominal
heat output
elmax 0.014 KW Type of heat output/room temperature control
At minimum
heat output
elmin 0.014 KW Single stage heat output and no
room temperature control
No
In standby mode elSB 0.48 W Two or more manual stages no tem-
perature control
No

Read all the instructions before continuing to unpack or install this appliance. Carefully remove the appliance from its packaging and lay on the
floor with it’s back surface downward. Note: DO NOT stand the appliance on its frame as this may cause distortion. Check that the remaining
packaging contents correlate with the component checklist below. Please dispose of all packaging with care at your local recycling centre.
4.0 U PACKI G THE APPLIA CE
4
3.0 APPLIA CE DATA - CO TI UED GB IE
©2019 Focal Point Fires plc.
Other control options
Room temperature control with
presence detection
No
Room temperature control with
open window detection
No
With distance control option No
With adaptive start control Yes
With working time limitation No
With black bulb sensor No
Contact details Focal Point Fires, Avon Trading Park, Christchurch Dorset, BH23 2BT
5.0 COMPO E T CHECKLIST
QUA TITY DESCRIPTIO
1 Heater main body
1 Remote control
1 Instruction booklet
1 Top wall mounting bracket
1 Bottom wall mounting bracket
1 Fixing kit; 6x screws 6x wall plugs
2 Bracket screws
With mechanical thermostat room
temperature control
No
With electronic room temperature
control
No
Electronic room temperature con-
trol plus day timer
No
Electronic room temperature con-
trol plus week timer
Yes
6.0 SITE REQUIREME TS
This appliance is designed to be wall mounted using the mounting bracket and fixings provided. The wall should be relatively flat
and not interfere with any of the ventilation slots in the rear panel.
The wall must be structurally sound and of a material capable of withstanding moderate heat. Finished plaster, conventional
wallpaper, dry-lined plaster board are examples of suitable materials. Materials such as flock, blown vinyl, embossed paper and
cloth wall coverings which are sensitive to even small amounts of heat should be avoided, as some discolouration may occur.
It should be noted that the appliance creates warm convected air currents. These currents move heat from the room surround-
ings to, and up the wall surfaces adjacent to the heater.
Installing the heater next to these types of wall coverings or operating the heater where impurities in the air, (such as tobacco
smoke) exist, may slightly discolour wall finishing.
If the appliance is to be mounted on a dry lined or timber framed construction then the integrity and ability of the wall to
carry the weight of the appliance must be confirmed. It is important in these circumstances that any vapour barrier and/or
structural members of the house frame are not damaged.
If you are unsure of the ability of the wall to carry the weight and/or which type of wall fixing to use, you should take profes-
sional advice and obtain the correct fixings. Alternatively, find a more suitable wall location.

5©2019 Focal Point Fires plc.
The wall where the appliance is to be
installed must be capable of long-
term support of the total load of the
appliance. Measures should also be
taken to ensure sufficient strength to
withstand the force of earthquakes,
vibration and other external forces.
Plasterboard alone is not considered
to be a structural material. It is not
recommended to rely on plaster-
board fixings alone to support the
weight of the appliance.
WAR I G
8.0 I STALLI G THE APPLIA CE
It is important that the following clearances are maintained from the appliance to combustible materials. These clearances are
dependent on the mounting location as defined below:
• The minimum distance from the top of the appliance to a ceiling is 100mm
• The minimum distance from the bottom of the appliance to the floor is 200mm
• The minimum distance to the sides of the appliance is 100mm
• The minimum distance to the front of the appliance is 500mm
7.0 CLEARA CES TO COMBUSTIBLE MATERIALS
CAUTIO : DO OT CO ECT THE APPLIA CE TO THE
ELECTRICAL SUPPLY AT THIS TIME.
Focal Point Fires plc. assumes absolutely no responsibility for injuries and damages
that may occur due to improper installation or handling.
Remove any protective film coatings from the finished/decorative surfaces of the
appliance, if any. After having selected the final mounting position of the appliance
taking into account the integrity of the wall the firebox of the appliance may be
secured to the wall.
To ensure customer safety, be sure to design the installation so that the strength of
both the wall and any wall fixings used are sufficient. The appliance should not be
installed until all wet plastering and/or dry wall sanding and wall painting has been
completed. Do not block the ventilation holes of the appliance. The wall onto
which the appliance is installed must be flat. Install only on a vertical surface. Avoid
sloped surfaces. Installation onto anything other than a vertical wall may result in
fire, damage or injury.
If the appliance is to be mounted on the inner leaf of a conventional cavity brick
wall, or a solid wall, then the wall plugs and fixing screws provided may be used.
Depending on the condition of the wall it may be necessary to use additional fix-
ings. In this situation, any additional fixings and wallplugs should be of the same size
and type as the ones provided.
If the appliance is to be mounted on a dry lined wall or a timber framed construc-
tion wall then efforts should be made to fix in at least two positions vertically, into
one of the wooden studs, or supporting wooden members of the wall using two
of the fixing screws provided. If this is not achievable then the wall should be
strengthened using appropriate building materials.
If there is no alternative than to rely on some plasterboard fixings then special cavi-
ty screw fixings or hollow wall anchors will be required which are not supplied with
this product. These should be constructed from metal and not plastic and of the
design indicated (Figure 1). For further guidance for wall fixing in timber framed
buildings refer to any relevant local codes of practice.
DO OT
• mount on a ceiling or floor
• recess any part of the appliance into the wall
• run the supply cable under carpets
• site any electrical equipment e.g. plasma screen TV sets etc, on the wall below the appliance
• site in a position where curtains or drapes could cover the appliance, or other soft materials could cover e.g. below a coat
rack
• site behind an opening door where mechanical impact/damage could occur
• site where the supply cable would become a trip hazard
• sit, stand or forcefully pull on the appliance
• obstruct, cover or force items into the openings
• use the heater to dry clothes
• site/use in an outdoor location(s)

Figure 1
6.0 SITE REQUIREME TS - CO TI UED GB IE
Figure 2
660
520
200
130

8.0 I STALLI G THE APPLIA CE - CO TI UED
6
GB IE
©2019 Focal Point Fires plc.
For optimum viewing install the fire out of direct sunlight. Ensure that the bracket
is level by using a spirit level whilst marking out the hole positions. Fix the wall
bracket using the plugs and screws provided. Carefully lift the heater up ensuring
that the top rear ledge of heater engages with the wall bracket and is sitting cen-
trally. This process should be carried out by two people to avoid injury or damage
to property or the appliance (figure 3).
Gently bring the heater down against the wall. Mark both the lower fixing bracket
fixing hole positions on the wall, remove the heater. Drill the wall and insert the
wall plug. Refit the heater to the wall and fasten the bottom fixing bracket to the
wall using the screw provided to permanently fix the heater in place (Figure 4).
Place the front decorative glass fascia over the front of the fire aligning the slots in
the brackets at each side of the front panel with the lugs on the sides of the fire
(Figure 5). Again two people will be required for this operation.
Check that the fan outlet, mounted on top of the appliance, is not covered or
obstructed in any way. Ensure the power to the fire is switched ON.
Figure 3
Figure 4
Figure 5
460
160
9.0 OPERATI G THE APPLIA CE
Switching O /OFF
Use the ON/OFF switch to power on the heater (set it to standby mode).
In standby mode, the heater can be operated either manually by the switches located at the top and right hand side of heater or by the sup-
plied remote control.
Manual Operation
OTE: The heater only starts working if the set temperature is higher than the ambient room temperature
Indicator lights
Buttons
Heater powered OFF
Heater powered ON, set to standby mode
Press to switch flame effect ON/ OFF
Press and hold to toggle between 5 different flame settings
POWER
Press once to activate the low setting (900W)
Press twice to activate the high setting (1800W)
Press a third time to switch the heater OFF
BACK IGHT Press to toggle between 7 different back light effects

9.0 OPERATI G THE APPLIA CE - CO TI UED
7
GB IE
©2019 Focal Point Fires plc.
Remote Operation
NOTE: The heater should be powered on using the ON/OFF switch before it can be operated using remote control.
The remote control requires 2xAAA size batteries (Not included).
Open the battery compartment by sliding the cover down and insert the batteries noting the polarity indicated in the battery compartment.
Keep batteries out of reach of children.
Remote control operations are identical to the functions on the control panel.
The remote control must be point directly at the sensor on control pad.
Display
Settings
Setting weekday and time
Press the DAY/TIME key. When the day is flashing press the ▲or ▼key to select the day.
Press the DAY/TIME key again, then press the + or – key to set the hour.
Press the DAY/TIME key again, then press the + or – key to set the minute.
Press the OK key to confirm the setting.
Switch the appliance ON
Set to standby mode
Go up in the menu
(change day)
Increase temperature
Increase hour/ minute
Set day/time
Set timer key
Go down in the menu
(change day)
Toggle between 5 different
flame brightness levels
Confirm selection
Cancel key Set automatic heating mode
Press once to activate the low setting
Press twice to activate the high setting
Press a third time to switch the heater OFF
Toggle between the 7 different back light effects
Decrease temperature
Decrease hour/ minute
Timer on/off key
2x AAA, 1.5V
Standby mode icon
Automatic heating mode
Time/ temperature display
Timer ON
Timer OFF
Temperature/
timer number
Flame brightness level
Timer icon
Day of the week
ow heat setting
High heat setting
Heating level

9.0 OPERATI G THE APPLIA CE - CO TI UED
8
GB IE
©2019 Focal Point Fires plc.
Setting temperature
NOTE: This setting is only applicable for the temperature in standard heating mode, not for the temperature in the timer mode. The default
set temperature is 25°C.
NOTE: The heater only starts working when the set temperature is higher than the room temperature.
Press the + or – key to set the temperature, which ranges from 15 to 30°C.
After the temperature setting has been completed, the display flashes about 5 seconds, then shows the room temperature.
Setting timer
Up to 10 different timer settings can be programmed.
Each timer setting has its day, power-on time and power-off time.
The maximum duration of each timer setting is 23 hours 50 minutes.
If the power-off time of the timer setting falls on the following day, it is unnecessary to set the day-just set the power-off time.
Press the TIMER SET key, the timer number starts blinking (01-10).
Press the + or – key to select a timer number.
Press the TIMER SET key, the cursor on the left side of the day blinks.
Press the ▲or ▼key to move the cursor to the corresponding day. Press the + key to add a corresponding day, or press the - key to delete a
day.
Press the TIMER SET key to set the on time. The hour digit starts blinking.
Press the + or – key to set the hour.
Press the TIMER SET key. The minute digit starts blinking.
Press the + or – key to set the minute.
Press the TIMER SET key to set the off time. The hour digit starts blinking.
Press the + or – key to set the hour.
Press the TIMER SET key. The minute digit starts blinking.
Press the + or – key to set the minute.
Press the TIMER SET key. The temperature digit starts blinking.
Press the + or – key to set the temperature.
Press the TIMER SET key to continue with the timer setting or press the OK key to confirm the setting.
Viewing the timer setting
Press the TIMER SET key.
Press the + or – key to check the power-on time of the set timers one by one.
To check the power-off time, press the ▲key.
Press the + or – key to check the power-off time of the set timers one by one.
To delete selected setting, press the C key.
Activation timer
Press the TIMER ON/OFF key to activate the timer function.
NOTE: When the timer is active, the heating level must be manually selected. If the heater function is not selected; only the flame effect goes
on at the set power-on time.
Automatic heating mode
Press the IC key to activate automatic heating mode. The AUTO icon appears on the display.
When the automatic heating is turned on, the heater automatically changes the heating level depending on the set temperature and the ambi-
ent room temperature.
10.0 SAFETY CUT-OUT SYSTEM
This appliance has a safety cut-out system fitted which will activate if the air inlets or heater outlets are obstructed. For safety reasons the fire
WILL OT switch on again automatically.
The following procedure must be carried out before the fire can be operated again:
1. Unplug the power supply cable at the outlet socket and place all switches to off at the appliance.
2. eave the fire OFF for a period of not less than 15 minutes, ensuring any obstructions are removed.
3. Plug in the power supply cable at the outlet socket, and then switch on at the appliance.
If the appliance fails to operate correctly, repeat the above procedure. If an attempt to switch on is made before the safety cut-out has reset,
the heaters may cut-out for a further period of time. If the sequence has been followed correctly and the heaters still fail to function, check the
power supply cable plug is plugged in at the outlet socket. If this is not the cause, call an electrician.

ALWAYS DISCO ECT THE APPLIA CE AT THE SUPPLY OUTLET SOCKET BEFORE U DERTAKI G A Y
CLEA I G.
Except for periodic cleaning of dust, there are no specific requirements for care, other than regular cleaning of the general appliance. A wipe
with a dry cloth is normally sufficient. DO NOT use abrasive cleaners as they can damage the finish. Make sure the heater outlet grille (locat-
ed next to the switches) are kept clear of dust, pet hair and other airborne household matter. These should be vacuum cleaned periodically
using a brush attachment.
The ED light strip is designed and tested to last 20,000 hours however, should a problem occur with the ED light strip this can be replaced.
The ED light strip can be purchased from Focal Point Fires (please see contact details on front cover). The light strip will be supplied with fit-
ting instructions.
Battery Replacement
Battery Requirements: 2x AAA 1.5V (batteries not included)
1. Remove the battery bracket and the used batteries from the back of the remote control.
2. Insert the 2x replacement batteries the correct way into the battery holder, making sure the batteries are firmly seated.
3. Then insert the battery bracket back into position.
11.0 CLEA I G A D MAI TE A CE
9
GB IE
©2019 Focal Point Fires plc.
There are no internal user serviceable parts.
Check regularly for security of wall fixings as appropriate. Also check security of supply cable and connections. If the supply cable
becomes damaged, it must be replaced by a service agent or competent person, such as a qualified electrician.
This appliance is supplied with a BS1363 3 pin plug fitted with a 13 Amp fuse. Should
the fuse require replacing, it must be replaced with a fuse rated at 13 Amp and
approved to BS1362. In the event of the mains plug being removed/ replaced for any
reason, please note : IMPORTA T: The wires in the mains lead are coloured in
accordance with the following code:
Blue - Neutral
Brown - ive
Green/ Yellow - Earth
As the colours of the wires in the mains lead of this appliance may not correspond
with the colour markings identifying the terminals in your plug, proceed as follows.
The blue wire must be connected to the terminal marked with an N or coloured
black. The brown wire must be connected to the terminal marked with an or coloured red. The green/yellow wire must be
connected to the earth terminal which is marked with an E or with the earth symbol. WAR I G: Never connect live or
neutral wires to the earth terminal of the plug.
NOTE: If a moulded plug is fitted and has to be removed take great care in disposing of the plug and severed cable, it must be
destroyed to prevent engaging into a socket.
Refer to Section 2.0, Appliance Data for fuse specification. Excluding fuses, use only genuine manufacturers spare parts available
from your supplier.
12.0 SERVICI G

13.0 GUARA TEE - TERMS A D CO DITIO S
10
F861506
GB IE
©2019 Focal Point Fires plc.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local
authority or retailer for recycling advice.
As our policy is one of continuous improvement and development, we therefore hope that you will understand we must retain the right
to amend details and/or specifications without prior notice.
Registration is not required.
The 3 year guarantee only covers products purchased on or after 1st February 2009. The 3 year guarantee commences from the date of purchase,
provided that the following 3 terms and conditions are adhered to:
1. For any claim to be made within the 3 years from date of purchase you will be required to provide and supply us with your proof of purchase.
2. Your gas fire must have been commissioned by a Gas Safe registered installer, evidence of which you must provide together with the Gas Safe regis-
tration number.
3. Your appliance must have been serviced annually, irrespective of use, by a Gas Safe registered installer, evidence of which must be provided, such as
the receipt.
Please note all consumable items such as any ceramics including coals, pebbles, matrix, front strips, panels and bulbs are not covered by the 3 year
guarantee.
We reserve the right to reject any claim or make a charge for any visit where the cause of the defect is due to non-compliance with the installation
and/or servicing instructions or misuse of the appliance.
If a repair is chargeable during the warranty period, we will inform you and where possible, provide a quote or price guide before starting work. We
cannot always give a firm cost until we commence the repair as it is not always possible to identify which components have been damaged.
Repaired or replaced products are covered only for the remainder of the original guarantee period and the guarantee period will not be extended
even if we repair or replace any product or part.
If we replace any component or product, the component or product removed will become our property.
We will not accept or reimburse the cost(s) of any third party who undertakes any work carried out on the product or fits parts, unless we have
approved such work in advance of it being carried out.
The Manufacturer’s guarantee does not apply to:
• Damaged caused by faulty installation, theft, tampering, neglect, misuse, normal wear and tear, accident, fire, flood, explosion, lightning, storms, frost or
other bad weather conditions.
• Damage caused by the non-observance of the Manufacturer’s Installation Instructions.
• Any unauthorised adjustments made to the product by a third party.
• Servicing and its associated costs.
• Self-maintenance tasks such as cleaning.
Making a claim is easy.
If you wish to make a claim under our 3 year guarantee, and all of the terms and conditions for your product have been met then please submit the
following information for the attention of the 3G Service Department to [e-mail]. Alternatively, you can fax to 01202 499326 or post
to Focal Point Fires plc, 3G Service Department, Reid Street, Christchurch, Dorset, BH23 2BT. Please note that this does not affect your statutory
rights.
Details required:
1. Name, full address (including post code) and contact telephone numbers.
2. Receipt of purchase or credit card statement.
3. Original installer’s Gas Safe* registration number (gas fires only).
4. Annual service receipt for every 12 months (gas fires only).