Foley 653 ACCU-Master User manual
THIS BOOK CONSISTS OF TWO MANUALS:
The OPERATOR'S MANUAL, which contains all the
653 ACCU-Master
633 ACCU-Pro with
ACCU-Touch 3
AUTO-INDEX
SPIN/RELIEF
REEL GRINDER
2
3
653/633
AUTO - INDEX
SPIN / RELIEF
REEL MOWER GRINDER
Patent No. 5,321,912
6,010,394 & 6,290,581
6,685,544 & 6,699,103
OPERATOR'S MANUAL
6537950 (02-2021)
YOU MUST THOROUGHLY READ AND UNDERSTAND ALL MANUALS BEFORE
OPERATING THE EQUIPMENT, PAYING PARTICULAR ATTENTION TO THE WARNING
ORIGINAL INSTRUCTIONS
4
IMPORTANT SAFETY MESSAGE
•
•
THROUGHOUT THIS MANUAL, THE FOLLOWING SAFETY SYMBOLS WILL BE USED TO INDICATE THE
5
TABLE OF CONTENTS
THIS MACHINE IS DESIGNED FOR SHARPENING REEL TYPE MOWER BLADES ANY USE OTHER
TO ASSURE THE QUALITY AND SAFETY OF YOUR MACHINE AND TO MAINTAIN THE WARRANTY,
YOU MUST USE ORIGINAL EQUIPMENT MANUFACTURER'S REPLACEMENT PARTS AND HAVE ANY
ALL OPERATORS OF THIS EQUIPMENT MUST BE THOROUGHLY TRAINED BEFORE OPERATING THE
PREPARATION/INSTALLATION CHECK LIST
ITEMS ARE COMPLETED BEFORE POWERING UP THE EQUIPMENT:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
6
OPERATING CONDITIONS
AMBIENT TEMPERATURE: +5°C/ 40°F to +40°C/ 100°F
RELATIVE HUMIDITY:
ALTITUDE:
TRANSPORTATION AND STORAGE: -25°C/-15°F to +55°C / 130°F
OPERATING CONDITIONS
AMBIENT TEMPERATURE: +5°C/ 40°F to +40°C/ 100°F
RELATIVE HUMIDITY:
ALTITUDE:
TRANSPORTATION AND STORAGE: -25°C/-15°F to +55°C / 130°F
SAFETY INSTRUCTIONS
FIG. 2
FIG. 1
7
INTERLOCK SYSTEM
NEVER OPERATE EQUIPMENT WITH THE INTERLOCK SYSTEM DISCONNECTED OR
1.
2.
3.
4.
5.
6.
7.
8.
LOW VOLTAGE RELAY
DAILY INSPECTION
THE DAILY INSPECTION SHOULD BE
PERFORMED ONLY WHEN THE MACHINE IS
1.
2.
3.
4.
FIG. 3
SAFETY INSTRUCTIONS
8
SAFETY INSTRUCTIONS
UNDERSTAND ANY PART OF THIS MANUAL AND NEED ASSISTANCE, CONTACT YOUR LOCAL DEALER OR
KEEP GUARDS IN PLACE
REMOVE WRENCHES AND OTHER
DON'T USE IN DANGEROUS ENVIRONMENT.
KEEP ALL VISITORS AWAY.
MAKE THE WORK AREA CHILD-PROOF with
ALWAYS USE SAFETY GLASSES.
maintenance.
DISCONNECT POWER BEFORE SERVICING, or
REDUCE THE RISK OF UNINTENTIONAL
NEVER LEAVE THE GRINDER RUNNING
Do not
DO NOT OPERATE GRINDER WHEN UNDER
THE INFLUENCE OF DRUGS, ALCOHOL, OR
9
SAFETY INSTRUCTIONS
DO
DOHANDLE AND STORE
CAREFUL manner.
DO VISUALLY INSPECT
DO CHECK MACHINE SPEED
DO CHECK MOUNTING FLANGES
and correct diameter.
DO USE MOUNTING BLOTTERS that are
DOWORK REST
DOUSE A SAFETY GUARD
COVERING
DONEWLY MOUNTED WHEELS to run
DOWEAR SAFETY GLASSES or some
DON'T
DON'THAS
BEEN DROPPED
DON'T FORCEOR
ALTER
DON'TEXCEED THE MAXIMUM
OPERATING SPEED
DON'T
ARE NOT CLEAN, FLAT AND
DON'T TIGHTEN
DON'TSIDE OF THE WHEEL
DON'TWHEEL
DON'T JAM
DON'T STAND DIRECTLY IN FRONT
DON'T FORCE THE GRINDING so that motor
AVOID INHALATION OF DUST
10
SAFETY INSTRUCTIONS
IF ANY DECALS ARE DAMAGED, REPLACE THEM IMMEDIATELY!
653
12
8
12
13
3
5
1
4
10
2
6
15
9
12
17
12
15
9
7
14
11
READ AND UNDERSTAND AND LOCATE ALL DECALS ON THIS MACHINE BEFORE
1
211
10
9
8
7
6
5
4
3
15
17
14
13
12
indicates that there are DANGEROUS
HIGH VOLTAGES PRESENT inside the
instructed to do so. REFER SERVICING TO
REFER TO MANUAL
POWER CORD PROTECTION – The
VACUUM -
SAFETY INSTRUCTIONS
16
MIN
3600
WINCH AND BOOM CAPACITY IS A MAXIMUM OF
12
12
8
DETAIL A
SCALE 1 : 5
13
3
5
61
10
4
7
2
8
17
11
15 9
16
9
14
19
14
14
SAFETY INSTRUCTIONS
IF ANY DECALS ARE DAMAGED, REPLACE THEM IMMEDIATELY!
19
633
13
READ AND UNDERSTAND AND LOCATE ALL DECALS ON THIS MACHINE BEFORE OPERATING
1
2
11
10
9
8
7
6
5
4
3
17
15
14
13
12
indicates that there are DANGEROUS
HIGH VOLTAGES PRESENT inside the
instructed to do so. REFER SERVICING TO
WARNING!
Refer to manual
POWER CORD PROTECTION – The
SAFETY INSTRUCTIONS
16
WINCH AND BOOM CAPACITY IS A MAXIMUM OF
18
19 VACUUM -
14
36"
[91CM]
165" [419 CM]
WORKSTATION
125
[318CM]
97"
[245CM]
OPERATOR &
LOAD AREA
AREA REQUIERD IF USING
THE OPTIONAL WORKSTATION
70
(178 cm)
71
(182cm)
61
(155cm)
94
(239 cm)
INSTALLATION INSTRUCTIONS
FIG.4
REMOVE GRINDER FROM WOOD PALLET
THE 633 UNIT WEIGHS 1450-
EQUIPMENT TO LIFT THE UNIT
POSITION BASE
MACHINE MUST BE POSITIONED TO ALLOW EASY ACCESS TO THE MAIN POWER CORD PLUG FOR USE
ELECTRICAL REQUIREMENTS:
- ALWAYS USE A PROPERLY GROUNDED OUTLET!
TO AVOID ISSUES FOLLOW THE WIRE SIZE RECOMMENDATION BELOW.
FOR 20 AMP RATED LARGE MACHINES
FIG. 5
15
INSTALLATION INSTRUCTIONS LIFTING LOCATION
6.
FIG. 6
LEVEL BASE
FIG. 7
FIG. 9FIG. 8
LOOSEN JAM NUT TO
ADJUST FOOT
LEVELING FEET LOCATED
AT CORNERS OF MACHINE
16
INSTALLATION INSTRUCTIONS
IT IS RECOMMENDED THAT THIS GRINDER HAS ITS OWN PERMANENT POWER CONNECTION
FROM THE POWER DISTRIBUTION PANEL, WITH NO OTHER MAJOR POWER DRAW
TRANSFORMER IS INSTALLED ON THE OUTSIDE OF THE MACHINE, THE POWER DELIVERED TO THE
POWER INSTALLATION
IF THE MACHINE DOES NOT HAVE A PLUG ON THE END OF THE MAIN POWER CORD, A PLUG OR
CONNECTOR THAT COMPLIES TO THE LOCAL LAWS AND REGULATIONS SHOULD BE INSTALLED BY A
WIRE THIS MACHINE DIRECTLY TO A POWER SOURCE WITHOUT A PLUG OR CONNECTOR UNLESS
A DEVICE THAT MEETS THIS CATEGORY 0 MAIN DISCONNECT REQUIREMENT IS USED TO PROVIDE
IMPORTANT GROUNDING INSTRUCTIONS
17
120 VAC 20 AMP
STANDARD PLUG FOR
NORTH AMERICA.
FIG.10
FOR 20 AMP RATED LARGE MACHINES
USE ONLY A QUALIFIED
ELECTRICIAN TO
COMPLETE THE
FIG. 11
H2, H3, H4, H7, H8 and H9.
X3 as
A
14 G. (2.5MM) GREEN
WITH YELLOW STRIPE
GROUNDWIRE TO BE
ADDED.
GREEN WITH YELLOW STRIPE
GROUND WIRE
GREEN WITH YELLOW STRIPE
GROUND WIRE
BROWN
LIGHT BLUE NEUTRAL
LIGHT BLUE
NEUTRAL
BROWN
POWER IN 230V, 1PHASE
POWER OUT 110V, 1PHASE
INSTALLATION INSTRUCTIONS
18
GETTING TO KNOW YOUR GRINDER
SYSTEMS
4. SPIN DRIVE
3. FRONT CLAMP WITH
HEIGHT ADJUSTER
GAUGE AND CYLINDER STOP
19
1. EMERGENCY STOP BUTTON or E-STOP
2. RESET BUTTON
3.
4. POWER SWITCH AND FUSES (RIGHT SIDE OF MACHINE).
POWER SWITCH turns OFF and ON the
THE POWER SWITCH IS NOT A MAIN DISCONNECT!
GETTING TO KNOW YOUR GRINDER
CONTROLS
ACCU-TOUCH 3 CONTROL
2. RESET BUTTON
3. TRAVERSE
1. EMERGENCY STOP BUTTON
SCREEN
FIG. 12
FIG. 13
20
TOUCH DISPLAY SCREEN EXPLANATIONS
EMERGENCY STOP SCREEN
RESET BUTTON down.
GETTING TO KNOW YOUR GRINDER
FIG. 14
TRAINER MODE
SELECTION
LANGUAGE
TOOLS
VACUUM START
OUTFEED
ALARM SCREEN
ALARMS SCREEN. A
START SCREEN
FIG. 15
This manual suits for next models
1
Table of contents
Other Foley Grinder manuals
Popular Grinder manuals by other brands
Metabo
Metabo W 1100-115 Original instructions
Optimum
Optimum OPTigrind GU 30 operating manual
Bosch
Bosch PEX 220 A Original instructions
Eastwood
Eastwood 20286 instructions
Sulzer
Sulzer Muffin Monster 10000 Series Installation, operating and maintenance instructions
Scheppach
Scheppach OSM100 Translation of original instruction manual
