Follett Horizon Elite 710 Series User manual

Horizon Elite™
self-contained 710 series Chewblet®ice machine
801 Church Lane | Easton, PA 18040, USA
1.800.523.9361 | 1.610.252.7301 | follettice.com
Features
Horizon Elite
710 series - up to 759 lb (345 kg) in 24 hours
- automatically transport ice through a tube with RIDE®
technology from up to 75' (22.9 m) away
- chewable, compressed nugget ice is preferred
over cubes¹
- Chewblet ice dispenses reliably from ice and
beveragedispensers
- available with approximately 1.00" (2.54 cm) long standard
Chewblet ice or optional 3/8" (0.95 cm) long Micro
Chewblet™ice
- quiet production without noisy harvest cycles
Revolutionary, scale inhibiting design
- produces ice that has 15% the TDS of the incoming water for
optimum dispensing and long life in drinks
- quarantines and regularly expels scale producing dissolved
solids to dramatically reduce scalebuildup
- increases time between descaling and reduces or eliminates the
need for expensive scale treatment
- saves 35% water compared to comparable cubers
- HCD and HMD models ENERGY STAR®certified
Durable, attractive ice machine
- regular bearing inspection or replacement is notrequired
- upgraded, easy-to-read LED operating status and
diagnosticdisplay
Designed with sanitation in mind
- Agion®silver-based antimicrobial product protection of key ice
and water contact components²
- floatless, sealed design inhibits formation of biofilms
- semi-automatic cleaning and sanitizing system
Warranty
- 3 years parts and labor, 5 years compressor parts³
Certifications
1Independent third party studies. Contact Follett for details.
2Disclaimer: Antimicrobial protection is limited to the treated components and does not treat water or ice.
³ Refer to price list for additional warranty information.
Short form specification:
Ice machine to be a Follett®Horizon Elite ice machine model
______________ [Insert size/series,condenser type and installation/
mounting, from model number guide] capable of producing compressed
nugget ice using an ecient, sanitary horizontal evaporator/auger
system and delivering ice by a flexible wire reinforced transport tube to
ice storage bin, iceand water dispenser, ice and beverage
dispenser or drop-in dispenser and provided with a stainless steel
frame and exterior, slide-out compressor/condenser with utility docking
station, front-mounted unit status display, evaporator water inlet
at harvest end with automatic flush while producing ice, and semi-
automatic cleaning and sanitizing system, plusall the featureslisted
below and mounting/performance-enhancing accessories checked.
Model configurations
For use with
1Install/mount Condenser V/Hz/Ph Item number 2
ice storage bin
top mount air
115/60/1 HCD710ABT
230/50/1 HCE710ABT
RIDE air
115/60/1 HCD710ABS
230/50/1 HCE710ABS
Follett Vision™
undercounter
ice and beverage
dispenser
RIDE air
115/60/1 HCD710AVS
230/50/1 HCE710AVS
countertop
ice and beverage
dispenser
(by others)
top mount
3air
115/60/1 HCD710AHT
230/50/1 HCE710AHT
RIDE air
115/60/1 HCD710AHS
230/50/1 HCE710AHS
drop-in dispenser
(by others) RIDE air
115/60/1 HCD710AJS
230/50/1 HCE710AJS
1Ordered separately.
2For Micro Chewblet ice, replace second character (C) with an M
e.g. HMD710ABT.
3Requires top kit (see page 4).
“E” models only

2
Form# 8225 Self-contained 710 series ice machine
Specification
W1 Width 22.70" (57.7 cm)
Fits on 22.00" wide dispensers
D1 Depth 24.50" (62.2 cm)
H1 Height 21.25" (54.0 cm)
Clearance topmount–1.00"(2.54 cm)
RIDE – See page 5-6 for details
C1 Electrical
115 V/60/1 – HCD and HMD models
11.3 amps, requires dedicated
15 amp circuit,
6' (1.8 m) cord, NEMA 5-15 plug
C2 Electrical
230 V/50/1 – HCE and HME models
6.0 amps, requires dedicated 15 amp
circuit, 6.5' (2 m) cord only.
Operating power 0.7 kW
C3 Ice transport tube see page 8 for details
C4 Water inlet 3/8" OD push-in water inlet
C5 Drain 3/4" MPT, 1" drain required
see page 7 for details
C6 Ice bin signal cord for Vision applications only
Air temperature 50 -100 F (10 - 38 C)
Water temperature 45 - 90 F (7 - 32 C)
Potable water pressure 10 - 70 psi (69 - 483 kPa)
Ice production see ice production chart on page 8
Energy consumption
90 F (32 C) air,
70 F (21C) water
4.78 kWh per 100lb(45.4 kg) ice
Heat rejection 8,500 BTU/hr (2,143 Kcal/hr)
Water consumption 12.0 gal (45 L) of potable water per
100 lb (45.4 kg) of ice (per AHRI test
standards). 12.4 gal (46.9 L) at low
TDS flush setting.
Refrigerant R404A – HCD and HMD models
R449A – HCE and HME models
Approximate ship weight 190 lb (86 kg)
Approximate net weight 180 lb (82 kg)
NOTE: For indoor use only
Dimensional drawing
W1 D1
H1
air
intake
C4
C5
G
C1 C2
C3
NEMA 5-15
right angle
C6
6.8"
(3.09 cm)
6.09"
(2.76 cm)
19.59"
(8.89 cm)
16.75"
(7.60 cm)
16.24"
(7.37 cm)
2.75"
(1.25 cm)
Accessories
Top kit for ice and beverage dispensers (page 4)
Water filters (refer to form# 9905)
Wall mount bracket (item# 00997098)
Ice machine stand, height-adjustable (item# 00997080)
Timer to control one or two ice machines (item# 00967265)
Longer ice transport tube (refer to price list, form# 4025)
NOTE: 10' (3 m) provided as standard for RIDE model.
Sleep cycle kit for improved energy eciency and component life
(item# 01338276)
NOTE: For countertop dispenser applications for models ending in
HS and HT.
SafeCLEAN Plus™ice machine cleaner
1 x 8 oz (237 ml) bottle(item#01147826)
6 x 8 oz (237 ml) bottles(item#01149954)
24 x 8 oz (237 ml) bottles (item#01149962)
SaniSponge™, 24 sanitary sponges (item# 01075431)

3
Form# 8225
Self-contained 710 series ice machine Self-contained 710 series ice machine
1 – Locating the ice machine
Horizon Elite self-contained Chewblet ice machines allow top-mounting or mounting in a base cabinet, on a wall or on a floor stand up
to 75' (22.9 m) from the dispenser or ice bin with RIDE technology. In-cabinet mounting (RIDE applications) require special attention to
service access, unit ventilation and ice tube runs (see pages 4-8).
Top mounting – ice and beverage
dispensers (by others)
RIDE model – Follett low-profile Vision
ice and beverage dispensers Top mount on Follett ice storage bins
Important specifier notes Important specifier notes Important specifier notes
1. Dispenser must be compatible with
nugget ice. See page 4 for compatible ice
and beverage dispenser models and top
kitnumbers.
2. Verify ceiling or soffit height to ensure
sufficient top clearance.
1. See pages 4-6 for critical clearance and
ventingrequirements.
2. Ice transport tube ships with Vision
ice and beverage dispenser (Vision
applicationsonly).
1. See form# 8590 for bin sizing.
2. Verify ceiling or soffit height to ensure
topclearance.
3. Locate floor sink or grate and drains in front
of storage bin.
4. Do not position bin drain lines to block
Ice•DevIce™bin cart.
RIDE model – ice and beverage
dispensers (by others)
RIDE model – drop-in beverage
dispensers (by others) RIDE model – Follett ice storage bins
Important specifier notes Important specifier notes Important specifier notes
1. Dispenser must be compatible with
nuggetice. Compatible dispensers
include Servend MD150/175/200/250,
SV175/200/250, MDH-402, and Follett
Symphony Plus™110CM as well as the
dispensers listed on page 4.
2. Coca-Cola Freestyle 7100 requires top
adapter ICCode 46751 and ice kit IC Code
46430 and must be ordered from Coca-Cola.
Coca-Cola Freestyle 9100 requires top kit
HSF26SC. Consult with Coca-Cola and Follett
to qualify application prior to ordering.
3. RIDE application is approved only for
PepsiSpire 3.0, 5.0 and 4.1 designed for top
mount ice machines and requires MSP24SC
for 3.0 and MSP30SC for 5.0 and 4.1, ordered
separately. For manual fill versions of
PepsiSpire 3.0, 5.0 and 4.1, contact factory.
4. See pages 4-6 for critical clearance and
ventingrequirements.
1. Compatible with the following dispensers:
Cornelius 1522, 1722, 2323 and Lancer
2200, 2300, 23300.
2. Requires 12.00" (30.5 cm) of access space
for installation on transport tube side.
3. See page 5-6 for critical
clearancerequirements.
1. See form# 8590 for bin sizing.
2. Locate floor sink or grate and drains in front
of storage bin.
3. Do not position bin drain lines to block
Ice•DevIce bin cart.

4
Form# 8225 Self-contained 710 series ice machine
1 – Locating the ice machine (continued)
Top mounting – compatible ice and beverage dispensers
1
Manufacturer Model number Width in (cm) Depth 2 in (cm) Height 3 in (cm) Top kit
Coca-Cola dispensers
Freestyle 7000 30.10 (76.5) 33.11 (79.0) 47.00 (119.4) H22F30-F 4
Freestyle 7100 30.00 (76.2) 33.80 (85.8) 47.00 (119.4) H22F30-F 4, 5
Freestyle 9000 25.50 (64.8) 35.50 (90.2) 73.75 (187.3) H22F24-F4, 6
Freestyle 9100 25.50 (64.8) 39.25 (99.7) 77.25 (196.2) H22F26-F 4
Cornelius dispensers
DB/ED/DF 150 series 22.00 (55.9) 30.75 (78.1) 35.63 (90.5) H22C22-F
DB/ED/DF 175 series 24.50 (62.2) 30.00 (76.2) 35.63 (90.5) H22C24-F
DB/ED/DF 200 series 30.00 (76.2) 30.95 (78.6) 35.63 (90.5) H22C30-F or H22C30-X 7
DB/ED/DF 250 series 30.00 (76.2) 30.95 (78.6) 39.63 (100.7) H22C30-F or H22C30-X 7
DB/ED/DF 300 series 44.38 (112.7) 30.00 (76.2) 39.63 (100.7) H22C44-F or B 8
FlavorFusion / Overload 30.00 (76.2) 33.13 (84.2) 41.00 (104.1) H22C30-F-FF
IDC215 30.00 (76.2) 33.13 (84.2) 36.69 (93.2) H22C30-F-IDC
IDC255 and Pro Fast Gate 30.00 (76.2) 33.13 (84.2) 39.75 (101.0) H22C30-F-IDC
IDC Pro 30.00 (76.2) 33.13 (84.2) 40.25 (102.2) H22C30-X-PRO⁸
Lancer dispensers
4500-22N 22.00 (55.9) 30.50 (77.5) 36.66 (93.1) H22L22-F
4500-30N 30.00 (76.2) 30.50 (77.5) 36.66 (93.1) H22L30-F
FS-22N 22.00 (55.9) 30.50 (77.5) 41.28 (104.8) H22L22-F
FS-30N 30.00 (76.2) 30.50 (77.5) 41.28 (104.8) H22L30-F
Bevariety 30.00 (76.2) 31.00 (78.7) 37.75 (95.9) H22L30-F-STP
Sensation 30" 30.00 (76.2) 31.00 (78.7) 38.25 (97.2) H22L30-F-STP
Sensation 44" 44.00 (111.8) 31.00 (78.7) 39.38 (100.0) H22L44-F-STP
Touchpoint 32.50 (82.6) 33.70 (85.6) 40.00 (101.6) H22L30-F-STP
Pepsi dispensers Spire 3.0 27.00 (68.6) 35.00 (88.9) 38.12 (96.8) H22P24-F
Spire 5.0 / 4.1 30.50 (77.5) 36.00 (91.4) 42.75 (108.6) H22P30-F
Servend dispensers MDH-302 42.75 (108.6) 30.50 (77.5) 35.16 (89.3) H22S44-F or B 9
1 All approved dispensers can be filled with a RIDE model Horizon Elite ice machine without a top kit except Pepsi Spire 3.0, 5.0 and 4.1, see page 3 for details.
2Requires minimum 1.00" (2.54 cm) clearance between back of dispenser and wall.
3Net height after installation of top kit (excluding height of ice machine).
4Consult with Coca-Cola and Follett to qualify application prior to ordering.
5 Top adapter IC Code 46753 and ice kit IC Code 46430 must also be ordered from Coca-Cola.
6Adapter must also be ordered from Coca-Cola. IC Code:46010 (Silver), 46011 (Red) or 46012 (Black).
7 Top designed with flexibility to accommodate front or back mounting.
⁸ Top designed with flexibility to accommodate front or back mounting.
9Specify “F” for front facing, or ”B“ for backward facing units.
2 – Undercounter/in-cabinet mounting
Cabinet details
Important specifier notes
Cabinet base
must be flat and free of obstructions
(no lip or utilities to block removal)
Cabinet door opening
24.00"W x 22.25"H
(60.9 cm x 56.5 cm) minimum
slides
out
1. Cabinet door opening
must meet minimum size
requirements shown and be
free of obstructions to allow ice
machine to slide out (no lip or
utilities to block removal).
2. Cabinet base must be capable
of supporting ice machine and
allow ice machine to rest flat on
cabinetbottom.
3. No counter supports, electric
or plumbing can run in front of
the icemachine.

5
Form# 8225
Self-contained 710 series ice machine Self-contained 710 series ice machine
3 – Undercounter/in-cabinet mounting and ventilation
Using Follett supplied grilles
Horizon Elite ice machines can be installed undercounter/in-cabinet to fill bins or dispensers using RIDE technology. Care must be
taken to ensure proper cabinet venting to avoid recirculation of hot air. Improper venting can cause ice machine outages.
air
in
exhaust
must mate directly
to air intake gasket
12.00" (30.5 cm) minimum
between ice machine
and dispenser
see dispenser
specification
sheet for
installation
requirements
18.00"
(45.7 cm) min.
electric
water
Ice transport tube
minimum 1/4" per foot
(2 cm per meter)
pitch toward ice
machine
secure to prevent dips
and traps from forming
supplied
grilles Horizon Elite
ice machine
Cabinet door
drain
24.50"
(62.2 cm) min.
22.25"
(56.5 cm)
min.
door & gasket
must mate
directly
cabinet door
2.00"
(5.08 cm)
2.00"
(5.08 cm)
cutout
side of
ice machine
bottom of
ice machine
18.00"W x 14.00"H (45.72 cm x 35.56 cm)
supplied air
intake grille Cutout for supplied air intake grille
22.25"
(56.5 cm)
minimum
24.50" (62.2 cm) min.
Locating
cutout
Front
Completed installation with
gasket and door in place –
side view
Horizon Elite ice machine
air intake gasket
Important specifier notes for using Follett supplied grilles
1. The supplied exhaust grille must be located at least 18.00"(45.7cm)
from the supplied air intake grille (exhaust air must notrecirculate
with intake air).
2. Cabinet interior must be open to allow for unrestricted exhaust
airflow.
3. Ice transport tube needs minimum 1/4" per foot (2 cm per meter)
pitch toward ice machine and should be secured to prevent dips and
traps from forming.
4. Cabinet door must mate directly to air intake gasket.
5. Cabinet interior must provide a minimum clear space of 24.50"
(62.2cm) deep by 22.25" (56.5 cm) high.
6. Cutout for supplied grilles must meet minimum size requirements
shownabove.
7. Utilities should be conveniently located as shown.

6
Form# 8225 Self-contained 710 series ice machine
3 – Undercounter/in-cabinet mounting and ventilation (continued)
Using grilles by others/alternate cabinet ventilation
Cabinets with ventilation or louvers other than those provided require special consideration to provide proper ventilation.
Recirculation of hot air will reduce ice machine performance and can cause ice machine outages.
grilles by others/
alternate cabinet
ventilation
all counter ventilation
within 18.00" (45.7 cm) of
air inlet must be blocked to
prevent exhaust-air recirculation
Cabinet door
must mate directly
to air intake gasket
exhaust
air in
exhaust
18.00" (45.7 cm)
minimum
18.00" (45.7 cm)
minimum
Minimum open air space
Horizon Elite ice machine
air intake gasket
cabinet door
door & gasket
must mate
directly
grilles by others/
alternate cabinet ventilation
= sq in of open air space
= (# of openings)
minimum 160 sq in
(1,032 sq cm)
open air space
side
view
y
x
xxx
yn
n
Important specifier notes for using grilles supplied by others/alternate cabinet ventilation
1. Exhaust must be at least 18.00"(45.7cm) from air intake (exhaust air
must notrecirculate with intake air).
2. Cabinet interior must be open to allow for unrestricted exhaust
airflow.
3. Ice transport tube needs minimum 1/4" per foot (2 cm per meter)
pitch toward ice machine and should be secured to prevent dips and
traps from forming.
4. Ducting must be provided if cabinet door does not mate directly to
air intakegasket.
5. Cabinet interior must provide a minimum clear space of 24.50"
(62.2cm) deep by 22.25" (56.5 cm) high.
6. Grilles by others must meet minimum requirements for open air
space shownabove.
7. Utilities should be conveniently located as shown.

7
Form# 8225
Self-contained 710 series ice machine Self-contained 710 series ice machine
4 – Horizon Elite ice machine mounting accessories
Optional wall mount bracket Optional machine stand Important specifier notes
22.00"
(55.9 cm)
25.50"
(64.8 cm)
23.00"
(58.4 cm)
13.00"
(33.0 cm)
18.70"
(47.5 cm)
22.25"
(56.5 cm) 16.50"
(41.9 cm)
6.88"
(17.48 cm)
1. For secure wall mounting, specify
optional wall mount bracket.
2. Wall and fasteners must support the
weight of the ice machine, bracket,
supply water and ice. Use of a backing
board may be required with hollow
wallconstruction.
3. Machine stand mounting adds 6.88"
(17.5cm) to height of ice machine.
4. No dips in tube routing allowed.
5. Ice transport tube needs minimum 1/4"
per foot (2 cm per meter) pitch toward
ice machine and should be secured to
prevent dips and traps from forming.
5 – Horizon Elite drain - specifier guidelines
Flush drain plumbing – For regular machine drainage Important specifier notes: Where code
allows, follow recommendation below.
➌
➊
3/4" barb x 3/4" FPT
1" Stand pipe/drain
2 ft x 1" OD
silicone tubing
Minimum 8"
radius
3/4" MPT x 1" slip
➋
1. Connect the silicone tubing to the ice machine
3/4" drainbarb ➊.
2. Assemble the 3/4" barb x 3/4" FPT to the 3/4"
MPT x 1"slip. Connect the other end of the
silicone tubing to the 3/4" barb ➋.
3. Connect the 1" slip fitting to the 1" stand pipe/
drain ➌.
Note: Minimum 8" radius on silicone drain line.
Drain line from the ice machine must have at least
1/4" per foot pitch (6.4 mm/0.3 m).
Note: Stand pipe/drain provided by others. All
other components provided with ice machine.
Chassis drain plumbing – To assist with condensate in high humidity areas Important specifier notes: Where code
allows, follow recommendation below.
1. Plug must be removed from John Guest fitting.
2. Route 3/8" drain tubing through knockout in back
of docking station and insert fully into John Guest
fitting connection at the rear of the machine
chassis. Route other end of 3/8” drain tubing
todrain.
3. Drain must slope 1/4" inch per foot
(6 mm per 30.4 cm).

Self-contained 710 series ice machine
801 Church Lane | Easton, PA 18040, USA
1.800.523.9361 | 1.610.252.7301 | follettice.com
8225-202205 | © Follett Products, LLC
Ice production – Horizon Elite 710 series, air-cooled 60 Hz
Inlet water
temperature
F (C)
Ambient air temperature F (C)
60 (16) 70 (21) 80 (27) 90 (32) 100 (38)
lb (kg) production in 24 hr
50 (10) 787 (357) 759 (345) 705 (320) 639 (290) 603 (274)
60 (16) 750 (341) 702 (319) 666 (302) 624 (283) 570 (259)
70 (21) 707 (321) 681 (309) 636 (289) 586 (266) 542 (246)
80 (27) 677 (307) 629 (286) 611 (277) 559 (254) 518 (235)
90 (32) 642 (291) 600 (272) 580 (263) 539 (245) 497 (226)
Ice production – Horizon Elite 710 series, air-cooled 50 Hz
Inlet water
temperature
F (C)
Ambient air temperature F (C)
60 (16) 70 (21) 80 (27) 90 (32) 100 (38)
lb (kg) production in 24 hr
50 (10) 664 (301) 617 (280) 576 (261) 538 (244) 500 (227)
60 (16) 645 (293) 601 (272) 560 (254) 521 (236) 481 (218)
70 (21) 626 284) 582 (264) 544 (247) 506 (229) 464 (210)
80 (27) 588 (267) 544 (247) 512 (232) 481 (218) 389 (176)
90 (32) 557 (252) 519 (235) 487 (221) 455 (207) 328 (149)
ENERGY STAR and the ENERGY STAR mark are registered trademarks owned by the U.S. Environmental Protection Agency.
Agion is a registered trademark of Sciessent LLC.
HORIZON ELITE, ICE•DEVICE, MICRO CHEWBLET, SAFECLEAN PLUS, SANISPONGE, SYMPHONY PLUS and VISION are trademarks of Follett Products, LLC.
CHEWBLET, FOLLETT and RIDE are registered trademarks of Follett Products, LLC, registered in the US.
Follett reserves the right to change specifications at any time without obligation. Certifications may vary depending on country of origin.
6 – Horizon Elite ice tube runs - specifier guidelines
Long tube runs for RIDE remote ice delivery equipment
1/4"
1'
maximum
2' (60.9 cm)
beverage
dispenser
wall-mounted
ice machine
support
straps
transport tube slope
(toward ice machine)
(2 cm per meter)
minimum of
6.00" (15.24 cm)
turn/corner
radius
ice transport tube –
1 3/16" OD,
2 1/8" OD with insulation
Important specifier notes
1. 75' (22.9 m) maximum ice transport
tuberun.
2. Tubing routing bends must have a
6.00"(15.24 cm) radius or larger.
3. Dips and traps are not allowed. If not
supported from underneath, secure
insulated ice transport tube at least
every2' (60.9 cm) to prevent drips
andtraps.
4. Relative humidity levels above 80%
in areas where the ice machine or ice
transport tube is located may produce
excessive condensation that will cause
water damage.
5. Contact factory for recommendations
on running tubing through a decorative
soffit orchase.