Follett Horizon HMD700NHT User manual

Order parts online
www.follettice.com
Horizon™Ice Machine Installation Instructions
for Harmony™Top-mount Applications
HCD/HMD700RHT
HCD/HMD700NHT
(See model number congurator on page 2 for details.)
Horizon top-mount ice machines
t most countertop dispensers manufactured by
Cornelius • Lancer • SerVend
01012665R02
801 Church Lane • Easton, PA 18040, USA
Toll free [phone] • [phone]
www.follettice.com
remote condensing

2remote condensing HARMONY • TOP-MOUNT
A V SC 700HC
ConfigurationApplication
S RIDE®
(RIDE remote ice
delivery equipment)
T Top-mount
400 up to
454 lbs
(206kg)
700 up to
750 lbs
(340kg)
1000 up to
1036 lbs
(471kg)
1400 up to
1450 lbs
(658kg)
1650 up to
1580 lbs
(717kg)
V Vision™
H Harmony™
B Ice storage
bin
J Drop-in
M Ice Manager™
diverter valve
system
CondenserSeriesVoltageMachine
C 208-230/60/1 (icemaking head)
Self-contained only.
D 115/60/1 (icemaking head)
Self-contained and remote.
If remote unit, high side is
208-230/60/1.
E 230/50/1 (icemaking head)
Self-contained only.
MC Maestro™
Chewblet
(400 Series)
HC Horizon
Chewblet
(1000, 1400,
1650 Series)
HM Horizon
Micro
Chewblet
A Air-cooled, self-contained
W Water-cooled,
self-contained
R Air-cooled, remote
condensing unit
N Air-cooled, no condensing
unit for
connection to parallel rack
system
Chewblet®Ice Machine Model Number Configurations

HARMONY • TOP-MOUNT remote condensing 3
Front cover
8
Internal connection
7
Ice transport tube
5
External connection
6
Louvered docking assembly
4
Dispenser preparation
3
Site preparation
2
Unpack
1
Read and complete the following 8 installation steps

4remote condensing HARMONY • TOP-MOUNT
Carefully unpack and inspect the contents of your Follett ice machine. 1
Unpack
7/16"
7/16"



Unpack ice machine
1. 1

HARMONY • TOP-MOUNT remote condensing 5
Prepare the installation site. 2
➎
➍
3/8" ∅ (9,5mm)
1/4"
1'
NEMA
5-15
➋➊
➌
Site preparation
Electrical ➊
• 120/60/1-6 amps
Potable water supply ➋
• 10-70 psi (69-483kpa)
• 45-90 F (7-32 C)
• Water supply must be treated by a scale-inhibiting lter (item# 00130286)
Drain ➌
• The drain line from the ice machine must be vented and have at least 1/4” per foot pitch
(6,4mm/0,3m)
Refrigeration lines ➍
• 5/8” (15,8mm) diameter suction (insulated) ➍
• 3/8” (9,5mm) liquid ➎
2.1
Provide drainage, water supply and electrical power to within 6 feet (2m) of ice
machine in accordance with local and national codes. Outdoor installation of
low side is not recommended and will void warranty.
Installation site requirements
2.1

6remote condensing HARMONY • TOP-MOUNT
Prepare the dispenser. 3
Dispenser preparation
Note: The instructions below only apply to 22" & 30" wide dispensers.
44" wide dispenser instructions may be found with the top kit.
➊
➊
All models
• Remove protective tape from gaskets ➊
Top preparation – ALL
3.1
➋
➊
➊
➌
• Apply gaskets
➊.
• Install coupling
➋ through bottom of
dispenser top and secure with locking nut
➌
Top preparation – ALL
3.2
➋
➊
Cornelius models only
• Remove protective tape ➊
• Apply gasket
➋
Top preparation – CORNELIUS
3.4
➋
➊
• Screw 4" (102mm) extension ➊ into
bottom of shuttle actuator ➋
Top preparation – ALL
3.3

HARMONY • TOP-MOUNT remote condensing 7
PRESS IN ON
THIS SIDE TO
TURN SWITCH
ON.
SWITCH
ON
SWITCH
OFF
PRESS IN ON
THIS SIDE TO
TURN SWITCH
OFF.
ROCKER
SWITCHES
(VIEW LOOKING
DOWN)
SIDE VIEW
SIDE VIEW
12345678
OFF
SWITCH
NUMBER
AGITATION FREQUENCY
NO AGIT
ATION
10 MINUTES
20 MINUTES
30 MINUTES
40 MINUTES
50 MINUTES
60 MINUTES
70 MINUTES
80 MINUTES
90 MINUTES
100 MINUTES
110 MINUTES
120 MINUTES
130 MINUTES
140 MINUTES
150 MINUTES
5
6
7
8
O
O
O
O
O
O
O
X
O
O
X
O
O
O
X
X
O
X
O
O
O
X
O
X
O
X
X
O
O
X
X
X
X
O
O
O
X
O
O
X
X
O
X
O
X
O
X
X
X
X
O
O
X
X
O
X
X
X
X
O
X
X
X
X
SWITCH
NUMBER
AGITATION TIME
1 SECOND
2 SECONDS
3 SECONDS
4 SECONDS
3
4
O
O
O
X
X
O
X
X
X = ON
O = OFF
Lancer 4500 series only
Adjust the agitation time to 1 second, and the agitation frequency to 150 minutes.
Note: See Lancer manual for more information.
Agitation adjustments – LANCER 4500 SERIES
3.7
➊
➋
➋
ON
OFF
Lancer models only
• Remove protective tape ➊
• Apply gaskets
➋
Top preparation – LANCER
3.5
Cornelius models ED, DB, DF, IDC
and Flavor Fusion
Adjust the agitation timer located on the
Cornelius PC board to 1 second on, 1 hour
off. Note: see Cornelius manual for more
information.
Agitation adjust. – CORNELIUS
3.6

8remote condensing HARMONY • TOP-MOUNT
Major/Minor
FS-16 Setup
Config Bonus Key
Soda/Plain Water
Config Dispense Only
PC Mode
PC Time
Ice Stir Off
Ice Stir On
Sold Out
Carb Sensors
Ice Bin Sensors
Valve Code Version
Number Of Valves
Reset Defaults No Yes
Reload Defaults?
1 2 3 4
12 0.104 0.104
1000
Ice Bin Optic
Upper Lower
Sold Out #1
Selection Sold Out
05000
On Time (MSEC)
Off On
Set PC Mode Menu
V:1 B1 DLY1
Dispense Delay
V:2 1:S 2:W 3:S 4:W
V:1 T:F M:S B:W
Bonus Key Setup
Brands Per Side
V:1 L:2 R:1
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
Soda/Plain Water
OFF Time (MIN)
00150
On Time (MSEC)
01000
1000 500
34 0.104 0.104
On On On On
V:1 B:1
Sold Out #1
Off
Sold Out #1
Ver. 0.200
Lancer FS-16
Sub-CatagoryMain Menu
Initialization Screen
2nd Sub-Catagory
(Boot Up Only)
Cancel Enter
Scrolls through Main Menu
Press "Enter" to enter sub-catagory
Moves curser to right or left
Changes value (number/letter)
Press "Enter" to enter save changes
Press "Cancel" to exit menu
➊
Lancer FS series only
• Hold down “cancel” and “left button” to get to hidden menu ➊
• Type in code 6655
• Type in 150 minutes of off time and 1000 milliseconds (1 second of time) as the preferred
setting
Note: See Lancer manual for more information.
Agitation adjustments – LANCER FS SERIES
3.8
Agitation adjustments – SERVEND
3.9
SerVend models only
No agitation adjustment required.

HARMONY • TOP-MOUNT remote condensing 9
P/N 307277 — Diverter plate
(single agitator Cornelius
dispensers and left-hand
dispense chute on dual-agitator
Cornelius dispensers)
P/N 307277 — Diverter plate
(single agitator Cornelius
dispensers and left-hand
dispense chute on dual-agitator
Cornelius dispensers)
Single Agitator
Dual Agitator
P/N 00996207 — Diverter plate
(right-hand dispense chute on
dual-agitator dispensers)
Dispenser diverter plate overview (Installation on next page)
3.10

10 remote condensing HARMONY • TOP-MOUNT
Cornelius IDC and Flavor Fusion
These dispensers require modications for compatibility with Chewblet ice. Agitation times must
be set to 1 second ON, 1 hour OFF and the ice restrictor plate must be adjusted to the fully open
position. See your beverage supplier for these modications.
ICE CHUTE
GATE MOUNTING PLATE
GASKET
STORAGE HOPPER
ICE DIVERTER
10-32 WASHER
FLANGE EXTENDS INTO
STORAGE HOPPER
THROUGH GATE
OPENING
APPLY RTV TO THIS
SURFACE TO SEAL
TO HOPPER GATE
MOUNTING PLATE
ICE CHUTE
COVER
Cornelius ED, DF and DB series only
These dispensers require the installation of an ice diverter at the dispenser opening.
• Disassemble chute assembly
• Discard factory restrictor plate
• Replace with alternate diverter plate (supplied)
Dispenser diverter plate installation – CORNELIUS ED, DF and DB SERIES
3.11