FoodSaver V365 User manual

And More
Additional Features & Tips
For more usage tips and safety information, please refer to the FoodSaver Reference Guide or visit our website at www.foodsaver.com.
Tips on Sealing a Bag
Make sure you’ve placed the bag in the proper
place. When making a bag from a roll, make sure end
of cut piece is on Sealing Strip, not over rubber gasket
or in Vacuum Channel.
Prevent moisture or liquid from being pulled into
the Vacuum Channel or trapped in the seal. Either
pre-freeze moist foods such as raw meat for 1-2
hours before vacuum packaging, or place a folded
paper towel between food and end of bag to absorb
excess liquids. Just be sure to leave at least 3 inches
between paper towel and end of bag so that bag seals
properly with paper towel inside.
Make sure the Vacuum Mode Switch (on V375 only)
is set to Vacuum and Seal.
Make sure you give appliance time to cool down.
Wait at least 20 seconds between seals. Under very
heavy usage, appliance will shut off automatically to
prevent overheating. If it does, wait 20 minutes to
allow appliance to cool off.
Tips on Removing Air from a Bag
Make sure you’ve placed the bag in the proper
place. When vacuuming and sealing a bag, make sure
open end of bag is inside Vacuum Channel.
Check for wrinkles in the bag along the Sealing
Strip. Wrinkles in seal may cause leakage and allow
air to come back into bag. Check for wrinkles in bag
along Sealing Strip before closing lid and vacuum
packaging. If you find wrinkles after sealing bag, sim-
ply cut bag open and vacuum package again.
If motor runs for more than 30 seconds without
stopping, you may need to adjust bag and try again. If
you are making initial seal on a piece of bag material with
two open ends, make sure bag is placed on Sealing Strip,
not on black rubber gasket. If you are vacuum packaging
with a bag, make sure open end is placed down inside
Vacuum Channel and make sure Accessory Hose is not
attached. If you are vacuum packaging with an accessory,
check Accessory Hose in appliance lid and in accessory
to ensure a tight fit. (On V375, also make sure Vacuum
Mode Switch (C) is set to Vacuum and Seal.)
The Removable Drip Tray (G) fits inside Vacuum
Channel (D), making cleanup easy when small
amounts of liquids are inadvertently pulled into
Vacuum Channel during vacuum process (see
FoodSaver Reference Guide for tips on preventing this).
Place Drip Tray into Vacuum Channel. Two bag
guides in Drip Tray help correctly position FoodSaver
Bags when vacuum packaging. Slip open end of bag
into guides before closing lid and vacuum packaging.
After each use, empty Drip Tray and wash in warm
soapy water or place on top rack of dishwasher.
Appliance can be used without Drip Tray.
Removable Drip Tray
Copyright © 2004 Tilia, Inc. All rights reserved. This material may not be reproduced or redistributed in any fashion without the express written consent of Tilia, Inc.
FoodSaver and the Freshness Shield logo are trademarks or registered trademarks of Tilia Int’l, Inc. in the United States and other countries. All other trademarks are
property of their respective owners. Tilia, Inc. and Tilia Int’l, Inc. are Jarden companies.This product is protected by one or more of the following Patents:
U.S. RE 34,929; 4,660,355; 4,941,310; 5,655,357; 6,058,998; 6,256,968; Canada 1,315,746; and their equivalent international patents. Other patents pending.
First Printing: 3/2004 Item # TI8-0104 (03/04)

Features
QuickStart
V365/V375
Shown V375; V365 operates in the same manner.
Accessory Port
Open/Cancel Button
B
AVacuum Mode Switch
(V375 only)
C
Sealing Strip
Removable Drip Tray
Rubber Gasket
H
G
F
Vacuum Channel
Accessory Hose
E
D
Features of Your FoodSaver Appliance
For important safety information and helpful tips, please refer to the FoodSaver Reference Guide included in your kit.
Questions? Visit us at www.foodsaver.com or call 1-800-777-5452 (U.S.) or 1-877-804-5383 (Canada),
Mon-Fri 8am-8pm, Sat 9am-6pm EST. Get tips on vacuum packaging and order FoodSaver accessories.

Bags & Rolls
1. Place item(s) in bag, allowing at least 3 inches of
space between bag contents and top of bag.
2. Open appliance lid and place open end of bag
down into Vacuum Channel (D).
3. Close lid. (On V375 only, set Vacuum Mode
Switch (C) to Vacuum and Seal.)
4. To begin vacuum process, press down firmly on
lid with both hands until motor starts, wait 3-5
seconds, then release. Motor will continue to run.
5. When motor turns off, press the Open/Cancel
Button (B) to open lid and remove bag.
Refrigerate or freeze if needed. (See FoodSaver
Reference Guide for food safety tips.)
Tip: The Open/Cancel Button can also be used to
cancel vacuum process mid-way and open lid.
Note: Let appliance cool down for 20 seconds
after each use.
1. Cut enough bag material from roll to hold item
to be vacuum packaged, plus 3 inches. Be sure to
cut a straight line.
2. Open appliance lid and place one end of bag
material across Sealing Strip (F), not over black
rubber gasket (H).
3. Close lid. (On V375 only, set Vacuum Mode
Switch (C) to Vacuum and Seal.)
4. Press down firmly on lid with both hands until
motor starts, wait 3-5 seconds, then release.
Motor will continue to run.
5. When motor turns off, press the Open/Cancel
Button (B) to open lid and remove bag.
Now you are ready to vacuum package with your
new bag (see below).
Getting Started
Registering your appliance is quick and easy at www.foodsaver.com.
How to Make a Bag from a FoodSaver Roll
How to Vacuum Package with FoodSaver Bags
Place Bag on Sealing Strip Set Vacuum Mode Switch Press and Release Lid
Place Bag in Vacuum Channel Set Vacuum Mode Switch Press and Release Lid

g
Accessories
FoodSaver Accessory Guidelines
FoodSaver Accessories
Accessories include FoodSaver Vacuum Packaging Canisters, Universal Lids, Jar Sealers and Bottle Stoppers.
1. Always leave at least one inch of space between
contents and rim.
2. Wipe rim of canister, container or bottle to ensure
it is clean and dry.
3. Place lid on canister or container, or place stopper
in bottle.
4. For accessories with a large knob on lid, turn knob
to Vacuum. Vacuum package using instructions
below. When vacuum process is complete, turn
knob to Closed before removing Accessory Hose.
5. For accessories without a large knob on lid,
vacuum package using instructions below.
How to Open FoodSaver Accessories after Vacuum Packaging
FoodSaver Vacuum Packaging Canisters
(without large knob on lid)
To release vacuum and open, push gray rubber
button on lid.
FoodSaver Bulk Canisters and Quick Marinators
(with large knob on lid) and Universal Lids
To release vacuum and open, turn knob on lid
to Open.
FoodSaver Jar Sealer with Mason Jars
For use with Ball®and Kerr®brand Mason jars.
IMPORTANT: Do NOT use screw bands when
vacuum packaging jars. To open, wedge spoon
between Mason jar lid and highest part of threaded
rim. Twist spoon gently to release vacuum.
FoodSaver Bottle Stoppers
To release vacuum and open, simply twist and pull up
on Bottle Stopper.
How to Vacuum Package with FoodSaver Accessories
1. Prepare container according to FoodSaver
Accessory Guidelines above.
2. Insert one end of Accessory Hose (E) into
Accessory Port (A) on appliance. Insert other end
into port on accessory. Twist gray tab while inserting
to ensure a tight fit.
3. (On V375 only, set Vacuum Mode Switch (C)
to Accessory Mode.)
4. To begin vacuum process, press down firmly on lid
until motor starts, wait 3-5 seconds, then release.
Motor will continue to run.
5. When motor turns off, vacuum process is complete.
6. Gently twist and remove Accessory Hose from
accessory and appliance.
7. To test vacuum, simply tug on accessory lid. It should
not move.
Note: For important tips on using accessories
with different foods, please refer to the FoodSaver
Reference Guide.
Insert Accessory Hose Set Vacuum Mode Switch Press and Release Lid