Forever Redwood BENCH SWING SETS User manual

ASSEMBLY INSTRUCTIONS FOR THE
BENCH SWING SETS
866.332.2403 (TOLL FREE); 7am –7pm Pacific Time, Monday-Saturday

P| 1
Bench Swing Sets
www.ForeverRedwood.com
CONTENT OF BOXES - Frame Swing
No.
1
2
3
4
5
6
7
Drawing
Description
Posts
Legs
Supports
Diagonal Supports
Roof Supports
If ordered
Roof Panel
If ordered
Roof Board
If ordered
Qty.
2
2
1
4
2
2
1
Note: Part numbers in the Content of Boxes Table are for reference only. These do not match to the numbers marked on the parts sent.

P| 2
Bench Swing Sets
www.ForeverRedwood.com
CONTENT OF BOXES –Bench Swing
No.
8
9
10
Drawing
Description
Armrest
Seat
Backrest
Qty.
2
1
1
Note: Part numbers in the Content of Boxes Table are for reference only. These do not match to the numbers marked on the parts sent.

P| 3
Bench Swing Sets
www.ForeverRedwood.com
HARDWARE LIST
No.
A
B
C
D
E
F
G
H
I
J
K
Drawing
Description
3/8´´ x 7´´ Bolts
(To attach the posts to the legs).
3/8´´ x 8´´ Bolts
(To attach the diagonals supports to the posts and to
the support. / To attach the XL roof to the support).
5/16´´ x 3 ½´´ Bolts
(To attach the support to the pos.65ts. / To attach the
seat and the backrest to the armrest).
5/16´´ x 5 ½´´ Bolts
(To attach the roof supports to the posts).
5/16´´ x 4´´ Bolts
(To attach the roof panels to the roof supports).
3´´ Deck Screw
(To attach the roof panels to the di3agonal supports).
2 ½´´ Deck Screw
(To attach the roof board).
4´´ x 3/8´´ Eyebolts
(To attach the backrest to the armrest).
Quick Links
Springs
Chains
Note: Dimensions of your hardware will vary depending on size.

P| 4
Bench Swing Sets
www.ForeverRedwood.com
No
1
2
3
4
5
6
7
8
9
10
DESCRIPTION
Posts
Legs
Supports
Diagonal Supports
Roof Supports
Roof Panel
Roof Board
Armrest
Seat
Backrest
Note: Part numbers in the Drawing are for reference only. These do not match to the numbers marked on the parts sent.

P| 5
Bench Swing Sets
www.ForeverRedwood.com
Option A –Without Roof
Step 1: Attach the post (1) to the legs (2) with 3/8´´ x 7´´ bolts (A) and 3/8´´ x 8´´ bolts (B). Each part has a series of numbers
that indicate where to attach the part with the corresponding number.
Step 2: Put the Quick Links (I) and the Springs (J) in the hanger’s support. After that, put the chains (K). Take a few minutes to
adjust the chain height to your preference.
3/8´´ x 8´´ Bolts
1
1
2
Quick Link
2
3/8´´ x 7´´ Bolts

P| 6
Bench Swing Sets
www.ForeverRedwood.com
Step 3: Use 5/16´´ x 3 ½´´ bolts (C) to attach the support (3) to the posts. Each part has a series of numbers that indicate where
to attach the part with the corresponding number.
Step 4: Attach the diagonal supports (4) to the posts and to the support with 3/8´´ x 7´´ bolts (A). Each part has a series of numbers
that indicate where to attach the part with the corresponding number.
Note: If your Swing Set doesn´t include roof, then go to step 9.
3
5/16´´ x 3 ½´´ Bolts
4
4
3/8´´ x 7´´ Bolts

P| 7
Bench Swing Sets
www.ForeverRedwood.com
Option B –With Roof
Step 5: Attach the roof supports (5) to the posts with 5/16´´ x 5 ½´´ bolts (D). Each part has a series of numbers that indicate
where to attach the part with the corresponding number.
Step 6: Attach the roof panels (6) to the roof supports with 5/16´´ x 4´´ bolts (E) and to the diagonal supports with 3´´ deck screws
(F). Each part has a series of numbers that indicate where to attach the part with the corresponding number.
5
5
5/16´´ x 5 ½´´ Bolts
6
3´´ Deck Screws
5/16´´ x 4´´ Bolts

P| 8
Bench Swing Sets
www.ForeverRedwood.com
Note: If your Swing Set is XL follows this step. Otherwise go to step 8.
Step 7: Attach the roof panels (6) to the roof supports with 3/8´´ x 8´´ bolts (B). Each part has a series of numbers that indicate
where to attach the part with the corresponding number.
Step 8: Use 2 ½´´ deck screws (G) to attach the roof board (7) to the posts. Each part has a series of numbers that indicate where
to attach the part with the corresponding number.
2 ½´´ Deck Screws
7
3/8´´ x 8´´ Bolts

P| 9
Bench Swing Sets
www.ForeverRedwood.com
Step 9: Attach the seat (9) to the armrests (8) with 5/16´´ x 3 ½´´ bolts (A). Each part has a series of numbers that indicate where
to attach the part with the corresponding number.
Step 10: Attach the backrest (10) to the armrests with 5/16´´ x 3 ½´´ bolts (A) and 4´´ x 3/8´´ eyebolts (I). Each part has a series
of numbers that indicate where to attach the part with the corresponding number.
10
5/16´´ x 4´´ Bolts
9
8
8
5/16´´ x 3 ½´´ Bolts
5/16´´ x 3 ½´´ Bolts
4´´ x 3/8´´ Eye Bolts

P| 10
Bench Swing Sets
www.ForeverRedwood.com
Step 11: Finally, use quick links (I) to join the bench swing to the chains (K).

P| 11
Bench Swing Sets
www.ForeverRedwood.com
Option A –Without Swing Roof
Option B –With Swing Roof

P| 12
Bench Swing Sets
www.ForeverRedwood.com
This completes the Swing assembly. Hope you enjoy your set for many decades. If you ever have a problem or a question, don't
hesitate to call us (866 332 2403) or email us. We are here to support you.