fox fury 940K-010FI User manual

PRODUCT MANUAL
C-CLAMP 940K-010FI |BOLT 940K-010RSC |PICATINNY 940K-010PIC
SIDESLIDE SERIES

23
PHYSICAL CHARACTERISTICSSIDESLIDE REFERENCE GUIDE
Please read below before using your SideSlide as it relays beneficial operating
and safety information.
FLASHLIGHT (940–010FI OR 940– 012)
DIMENSIONS 5.5” long x 1.3” square head side
1.1” diameter handle (140 x 32 x 28mm)
WEIGHT 5.2oz (148g)
These application-specific SideSlide mounts allow the flashlight to be secured
to the Holder for quick and easy hands-free use.
C-CLAMP MOUNT (940K–010FI)
DIMENSIONS 1.5” x 2.8” x 1.6” (37 x 70 x 40 mm)
WEIGHT 3.7 oz (105 g)
BOLT MOUNT (940K– 010RSC)
DIMENSIONS 1.5” x 2.0” x 2.4” (37 x 51 x 61 mm)
WEIGHT 2.9 oz (82 g)
PICATINNY MOUNT (940K–010PIC)
DIMENSIONS 1.5” x 1.8” x 1.9” (37 x 45 x 49 mm)
WEIGHT 2.5 oz (70.8 g)
LANYARD
HOLE
RUBBER
SLEEVE
POWER/MODE SWITCHLOCKING GROOVE
STRIKE BEZEL
ANTI-ROLL HEAD TAILCAP
HANDLE
BOLT MOUNT PICATINNY MOUNT
C-CLAMP MOUNTHOLDER
RELEASE
LEVER
MOUNT
SCREW HOLES (3)
RELEASE
LEVER
MOUNT
THUMBSCREW (2)
RELEASE
LEVER
MOUNT
SCREWS (4)
RELEASE LEVER
FRONT

45
BATTERIES
The SideSlide Series flashlight requires one (1) 18650 battery or two (2)
CR123 batteries.
Mixing of new and used, or different brand batteries is not recommended
as this could lead to leakage or explosion.
BATTERY INSTALLATION AND REPLACEMENT
1. Twist the Tailcap in a counter-clockwise direction to remove it.
2. Insert the battery with the positive end first. (Respect appropriate polarity
when installing).
3. Re-install the Tailcap by twisting it in a clockwise direction back onto the
Handle. (Make sure the Tailcap is tightly sealed).
4. Test the light’s performance and function by activating the Power/Mode
Switch (located at the end of the Tailcap).
BATTERY LIFE
MODE 940K-010FI & 940K-010RSC 940K-010PIC
HIGH POWER 4 hrs 90 minutes
LOW POWER 10 hrs 10 hrs
BLINKER 8 hrs —
TURBO-STROBE™— 4 hrs
*Battery life may vary according to mode selected, battery quality and prevailing ambient conditions.
OPERATIONAL MODES
FOR THE C-CLAMP AND BOLT MOUNTS:
For HIGH mode: Press the Power/Mode Switch once.
For LOW mode: Press and hold the Power/Mode Switch for 2.0–2.5 sec.
For BLINKER mode: While in LOW mode, press and hold the Power/Mode
Switch for an additional 2.0–2.5 sec.
FOR THE PICATINNY MOUNT:
For MOMENTARY mode: Press and hold the Power/Mode Switch. While
the Switch is depressed, the flashlight will operate in HIGH mode. When
the user removes pressure from the Switch, the light will turn OFF.
For HIGH mode: Press the Power/Mode Switch two (2) times in rapid
succession. The light will remain in HIGH mode.
For LOW mode: While in HIGH mode, press and hold the Power/Mode
Switch for two (2) seconds. The mode will change to a LOW setting.
For TURBO-STROBE™: Press the Power/Mode Switch three (3) times in
rapid succession.
For OFF or EXIT a mode: Press the Power/Mode Switch once. Then,
continue following the directions above to progress to desired mode.
NOTE:
The light does not retain the mode in memory. Once you turn the
flashlight ON, you will have to re-select the mode you desire.
When the light is ON in any mode, a rear green warning light will flash
(excluding Picatinny model).
+BATTERY –
1
2
TAILCAP
NOTES

67
The flashlight is easily securable and removable by using the unique SideSlide
Release Lever.
TO INSERT THE FLASHLIGHT INTO THE HOLDER:
INSERTING AND REMOVING THE
SIDESLIDE FROM THE HOLDER
1. Insert the flashlight by pushing it into the beveled opening on the front of
the Holder.
2. Once locked, the Release Lever falls into a groove on the handle, securing
the flashlight in place.
TO REMOVE THE FLASHLIGHT FROM THE HOLDER:
12
1. Press and hold the Release Lever.
2. While keeping the Release Lever pressed, pull flashlight out of the Holder.
INSTALLATION OF YOUR
SIDESLIDE MOUNT
SIDESLIDE C-CLAMP
The C-Clamp can be mounted on the right or left side of the helmet, above or
below the brim (based on user preference).
TO MOUNT ON THE RIGHT SIDE OF A HELMET:
Place mount on helmet at desired location and tighten thumbscrews.
TO MOUNT ON THE LEFT SIDE OF A HELMET:
There are two (2) screws which allow you to separate the C-Clamp from the
Holder and flip it 180° so that it can be worn on the left side of a helmet.
1. Using a 2 mm AF Hex Key* twist the screws counter-clockwise to remove.
2. Pull C-Clamp mount away from Holder.
3. Spin C-Clamp mount 180°.
4. Align holes on the C-Clamp mount with holes on the Holder. Re-insert
screws and tighten with Hex Key, turning clockwise until secured.
OPTIONAL TIP: Apply Loctite™as needed to secure screws.
*2 mm AF Hex Key not included
12
12 3 4

89
WARRANTY AND OTHER
INFORMATION
PRODUCT DURABILITY
Meets NFPA 1971-2007 Fire
Resistant Requirements: 500°F
(260°C) for 30 minutes
REFLECTIVE STICKER
For P/N 940K-010FI & 940K-010RSC
only. For your safety, and increased
visibility, a reflective sticker (enclosed
in box) may be placed on the side of
the SideSlide.
CARE/CLEANING
Your FoxFury product is a
professional tool, but regular
maintenance and care of your light
will maximize performance for you. As
needed, wash your FoxFury product
using a soft washcloth, clean water
and a mild soap. Be sure that the
flashlight’s Tailcap is SEALED before
washing. When done, pat dry with a
damp cloth.
AVAILABLE ACCESSORIES
C-Clamp Adaptor, P/N 85-010
Bolt Adaptor, P/N 85-011
Picatinny Adaptor, P/N 85-012
Flashlight for C-Clamp & Bolt
P/N 940-010FI
Flashlight for Picatinny
P/N 940-012
Pressure Switch Cap
(Picatinny Only), P/N 50-150
WARNINGS
FoxFury, LLC is not responsible for
the incorrect use of any FoxFury
Lighting product.
Lights are strong enough to
cause damage to the human eye.
Do not stare into LEDs for long
periods of time or from a close
range (less than 2 ft).
FoxFury, LLC is not responsible
for any injury or damage caused
during the use of this product.
Usage of this product must be
supervised by an adult when it is
being used by a minor.
Any FoxFury product should
be operated at speeds safe
enough to maneuver around
surrounding obstacles.
Do not use under the influence
of drugs or alcohol.
LIMITED WARRANTY
FoxFury, LLC (“FoxFury”) warrants
to the purchaser of this product
(“Buyer”) that for a period of two
years following purchase, this product
will be free from defects in material
and workmanship and will function in
substantial compliance with FoxFury’s
written specifications for this product
as specified in the instruction manual
or on FoxFury’s website located at
www.FoxFury.com. Buyer’s exclusive
remedy shall, in any case, be limited,
at FoxFury’s election, to: A) repair or
replacement of the defective product;
or B) refund of the purchase price for
this product.
INSTALLATION OF YOUR
SIDESLIDE MOUNT
SIDESLIDE BOLT
This mount has the ability to rotate and provide usable light at eight (8) distinct
positions, every 45°.
NOTE: Three (3) M4.0 Cap Head screws are needed to attach the mount to a
helmet. Length of screws is determined by thickness of the users helmet.
SIDESLIDE PICATINNY
Mounts on rifle, shotgun and helmet with Picatinny/MIL-STD 1913 rail.
NOTES
IPX7
1 M 2 M

10 11
Products are assembled in either
FoxFury’s controlled plant in Asia or
the USA, under strict quality control.
THE FOREGOING WARRANTY
IS THE ONLY WARRANTY
MADE BY FOXFURY WITH
RESPECT TO THIS PRODUCT.
TO THE EXTENT ALLOWED BY
APPLICABLE LAW, THERE ARE
NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND BY
THE FOXFURY, EXPRESS OR
IMPLIED, WITH RESPECT TO THE
CONDITION OR PERFORMANCE
OF THIS PRODUCT, INCLUDING,
BUT NOT LIMITED TO,
MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE.
THIS LIMITED WARRANTY
SHALL NOT APPLY IF THIS
PRODUCT IS NOT STORED,
HANDLED, INSTALLED OR
USED IN STRICT ACCORDANCE
WITH MANUFACTURER’S
SPECIFICATIONS AND
INSTRUCTION MANUALS, OR
WHICH HAS BEEN SUBJECT
TO MISUSE, ALTERATION,
NEGLIGENCE OR ACCIDENT.
1. The damaged part or product
must be returned to FoxFury
PRIOR TO any repair or
replacement. Shipping costs are
the responsibility of the claimant.
2. You must obtain a return
authorization (RMA) number
from FoxFury prior to returning
products. FoxFury is not
responsible for any damage
incurred while in transit.
3. Buyer will be required to
show proof of purchase—NO
EXCEPTIONS.
4. Any modifications to light, cable
or battery pack automatically
voids all warranties on this
product.
All warranty inquiries should be
directed to FoxFury’s Customer
Service Department to handle all
warranty/repair-related inquiries.
TO THE EXTENT ALLOWED
BY APPLICABLE LAW: (A) IN
NO EVENT, WHETHER DUE
TO BREACH OF WARRANTY
HEREUNDER OR ANY OTHER
CAUSE WHATSOEVER, SHALL
FOXFURY BE LIABLE FOR OR
OBLIGATED IN ANY MANNER
TO PAY CONSEQUENTIAL,
INCIDENTAL OR INDIRECT
DAMAGES, INCLUDING, BUT
NOT LIMITED TO, LOSS OF
PROFITS, COST OF SUBSTITUTE
PRODUCTS AND PERSONAL
INJURY OR PROPERTY DAMAGE,
WHETHER SUCH CLAIM IS BASED
ON CONTRACT OR TORT OR ANY
OTHER THEORY OF LAW, AND
(B) FOXFURY’S ONLY DUTIES IN
CONNECTION WITH THE SALE
OF THIS PRODUCT SHALL BE TO
HONOR THE LIMITED WARRANTY
SET FORTH HEREIN. TO THE
EXTENT THAT THIS LIMITED
WARRANTY IS INCONSISTENT
WITH APPLICABLE LAW, THIS
STATEMENT SHALL BE DEEMED
MODIFIED TO BE CONSISTENT
WITH SUCH APPLICABLE LAW.
CONTACT FOXFURY
FoxFury, LLC
Oceanside, CA 92056 USA
Toll-Free: 844-FOXFURY
Tel: [phone]
Fax: [phone]
Email: [e-mail]
www.FoxFury.com
All FoxFury products are designed in
Oceanside, CA. All FoxFury products
are manufactured with the highest
quality USA and foreign parts.
NOTES

FOXFURY.COM 12/2015