fox fury TAKER R40 User manual

PRODUCT MANUAL
700-331
TAKER R40

23
FULL ASSEMBLY
(TOP VIEW—POWER/MODE SWITCH VISIBLE)
DISASSEMBLED
POWER PACK
DISASSEMBLED
LIGHT HEAD
POWER/MODE
SWITCH
ADAPTOR
SHROUD
M6 BOLT
HOLES (2)
POWER PACK
BOLT (2)
CHARGE
INDICATOR
LED
CAPTURE ADAPTOR
POWER CONTACTS
USB
CHARGE
PORT
LOCKING
POST
LED CONTACT
CAVITY (2)
“O”-RING
ACCESS SCREW
LED MODULE
SCREW HOLE (4)
TABLE OF CONTENTS
INTRODUCTION
Taker R40 Reference Guide 3
Overview 4
Physical Characteristics & Warnings 4
POWER PACK
Charging the Power Pack 5
Reassembling the Taker R40 after Charging 6
Power Pack Life 6
OPERATION
Operational Modes 6
SHIELD INSTALLATION
Removing the Adaptor Shroud 7
Riot Shield Installation with Bolts 8
Riot Shield Installation with 3M Reclosable Fastener 9
Capture Shield Installation 10
Drilling Template 15
MAINTENANCE
Replacing the O-Ring 11
Removing the Guards 11
WARRANTY 12–13
CONTACT FOXFURY 13
TAKER R40 REFERENCE GUIDE

45
WARNINGS
When used for extended periods of time the R40 will become HOT to the
touch.
Do not stare into the LEDs for long periods of time or from a close range
(less than 2ft (.06m)).
FoxFury’s Turbo-Strobe™is purposely designed to induce disorientation.
Prolonged viewing may produce vertigo or even vomiting.
While using any FoxFury product, please operate at safe speeds.
Be sure to rinse the Taker R40 with fresh water immediately after use if
product has been subjected to chemicals or saltwater.
OVERVIEW
The Taker R40 is a compact and powerful LED Light, the first of its kind,
which has the ability to be fastened to a riot or capture shield, held by
hardware or with industrial-strength Reclosable fasteners. Mounted to the
inside of the shield, it prevents the light from being grabbed by the opposing
force, and gaining control of the shield. Having two different intensities
(650 Lumens on HIGH, and Turbo-Strobe™), makes it a powerful tool for LE,
Corrections, and the Military. A Charge Indicator and Quick Swap™Power Pack
makes the Taker R40,patents pending,unequaled in the field.
IMPORTANT!
PHYSICAL CHARACTERISTICS
Please read below before using your Taker R40 as it relays beneficial
operating and safety information.
TAKER R40
DIMENSIONS 2.6” x 2.4” x 3.8” (66 x 60 x 97mm)
WEIGHT 7.3oz (206g) with Power Pack and Light Head
2.4oz (69g) Power Pack
CHARGING THE POWER PACK
1. Press and hold the Power Pack Release Lever located on the Light Head
portion of the Taker R40.
2. While maintaining pressure on the Power Pack Release Lever, pull the Light
Head and the Power Pack apart.
If unable to pull apart easily (due to resistance of the internal rubber
gasket), try moving the Power Pack back and forth while pulling apart.
NOTE: Once apart, be sure to keep both ends dry and away from
water, moisture and dust. While the Power Pack and Light Head are
separated, the unit DOES NOT maintain its waterproof rating.
3. Insert the provided Micro USB Cable into the Power Pack— respect the
orientation/alignment. Then, insert the opposite end, USB (Type A) into a
USB compatible power source or into the included AC/DC Adaptor.
(Input: 100V–240VAC 50/60 Hz, Output: 5V DC 1000mAH).
The Charge Indicator will be solid red while charging. Once fully
charged, it will turn green.
Charging time will be approximately 2.5 hours.
After the Power Pack is charged, disconnect it from USB Cable.
IMPORTANT: The R40 in steps 1–3 is shown without the Adaptor Shroud and
is flipped to show the Power Pack Release Lever. The R40 does NOT need to
be removed from the Adaptor Shroud to change Power Packs.
1
1
2
3
2
3
!
!
!
!
Please fully charge the Power Pack before using the Taker R40 for the first
time.

67
REASSEMBLING THE R40 AFTER CHARGING
1. Install the Power Pack to the Light Head—confirm position of alignment
posts to their respected cavities.
2. Push both halves together. A ‘click’ should be heard as they become
locked together.
Test the light to make sure that the Power Pack is properly connected
to the Light Head by pressing the Power/Mode Switch.
POWER PACK LIFE
MODE POWER PACK LIFE LUMENS
CONTINUOUS ON 1 hr 650
TURBO-STROBE™ 1.75 hrs 650
*Power Pack life may vary according to age and ambient conditions.
1
2
REMOVING THE ADAPTOR SHROUD
1. Begin with the R40 in the "Top View" (positioned the same as the "Full
Assembly" diagram on pg. 3) and locate the two (2) pre-installed bolts (
and ) on the top of the Light Head. Then position the R40 into the "Side
View," and re-locate the two (2) pre-installed bolts.
2. While still in the "Side View," use a small adjustable wrench to hold the
bottom nut of one (1) of the bolts. Then, while still holding the wrench, use
the provided Hex Key (2.5mm AF) to loosen the top of the bolt by turning
counter-clockwise, until it comes off completely. Repeat this step again for
the second bolt.
3. Once both bolts are loose, the R40 can be removed from the Adaptor
Shroud by pulling it forward and off.
FOR REINSTALLATION: Repeat the steps above in reverse order.
1
2
2
3
3
1
OPERATIONAL MODES
For CONTINUOUS ON mode: Press and hold the Power/Mode Switch
once.
For TURBO-STROBE™ mode: From CONTINUOUS ON mode, press the
Power/Mode Switch once.
For OFF or EXIT a mode: From TURBO-STROBE™ mode, press the
Power/Mode Switch once.
LOW POWER INDICATOR*: At a low level, the Charge Indicator will flash
for approximately 0.5–1.0 sec. It is suggested that you then charge or
replace the Power Pack with a fully charged one.
NOTE: Once the LOW POWER INDICATOR comes on, there is approximately
1–2 minutes of power remaining.
A
B
TOP VIEW SIDE VIEW
A
B

89
RIOT SHIELD INSTALLATION
1. Drill two (2) holes in the riot shield using the included Drilling Template on
pg. 15.
2. Assemble the R40 light to the Adaptor Shroud then place the light against
the INSIDE of the riot shield.
3. Use a Phillips head screwdriver and crescent wrench to install and secure
the R40 to the inside of the riot shield using the supplied hardware (M6
bolt, washers, and nuts).
NOTE: Be careful not to overtighten the bolts!
INSTALLING THE R40 TO A RIOT SHIELD USING BOLTS INSTALLING THE R40 TO A RIOT SHIELD USING THE 3M
RECLOSEABLE FASTENER ADAPTOR
1
2
3
ADAPTOR
SHROUD
ADAPTOR
SHROUD
RIOT SHIELD
Place the shield in
FRONT of the R40.
(The shield pictured is cut in
half for this visual)
FRONT OF SHIELD FRONT OF SHIELD
INCLUDED HARDWARE
M6 Bolts (2)
Bolts (2)
Washers (8)
Nuts (4)
RIOT SHIELD
Place the shield in
FRONT of the R40.
(The shield pictured is cut in
half for this visual)
3M RECLOSABLE
FASTENER
(ADHESIVE SIDE)
Peel the backing and
place the adhesive
side against the back
of the shield.
3M RECLOSABLE
FASTENER
ADAPTOR
1. FIRST, REMOVE THE CAPTURE ADAPTOR. Assemble the 3M
Reclosable Fastener Adaptor to the Light Head using the included
hardware. Use a Phillips head screwdriver and crescent wrench to tighten
adaptors to each other (NOTE: Do NOT overtighten).
2. Align the center cutouts and press the 3M Reclosable Fastener together
with the 3M Reclosable Fastener Adaptor.
3. Peel the backing from the 3M Reclosable Fastener (exposing the adhesive)
and then press it firmly against the inside of the shield.
Press the 3M Reclosable Fastener adhesive firmly for at least 5 sec.
1
2
3
RIOT SHIELD INSTALLATION
INCLUDED HARDWARE
Bolts (2)
Washers (2)
Nuts (2)
CAPTURE ADAPTOR
(REMOVE THIS!)

10 11
CAPTURE SHIELD INSTALLATION
1. Drill two (2) holes in the riot shield using the included Drilling Template on
pg. 15.
2. Assemble the R40 light to the Adaptor Shroud AND the Capture Adaptor
then place the light against the INSIDE of the riot shield.
3. Use a Phillips head screwdriver and crescent wrench to install and secure
the R40 to the inside of the riot shield using the supplied hardware (M6
bolt, washers, and nuts).
NOTE: Be careful not to overtighten the bolts!
1
2
3
ADAPTOR
SHROUD
CAPTURE SHIELD
Place the shield in
FRONT of the R40.
(The shield pictured is cut in
half for this visual)
FRONT OF SHIELD
INCLUDED HARDWARE
M6 Bolts (2)
Bolts (2)
Washers (8)
Nuts (4)
CAPTURE ADAPTOR
1. Use a size T6 Star-Tip (TORX) driver or bit (not included) to take out the
screws on the top and bottom of the R40.
2. Once screws are loose, remove them and then lift up on the Guard to
remove it.
3. Repeat steps 1–2 to remove the Guard on the opposite side of the R40.
FOR REINSTALLATION, make sure to tighten the screws until they are snug.
MAINTENANCE
1. Separate the Power Pack from the Light Head (follow steps 1–2 in the
“Charging the Power Pack” section on page 5).
2. Using a #2 Phillips head screwdriver (not included) remove the screw from
the Light Head (reference “Disassembled Light Head” diagram on page 3).
3. The Retaining Tab and “O”-Ring can now be removed.
If the “O”-Ring does not fall out on its own when unscrewed, it may
need to be pulled out.
Examine the “O”-Ring for cracks. If cracks are found, a replacement
will be needed to ensure the R40 waterproof rating.
FOR REINSTALLATION, follow the above listed steps in reverse order. NOTE:
The “O”-Ring can be lubricated with a non-silicone based grease.
1
1
1
2
2
3
3
2 3
“O”-RING
RETAINING TAB
1 2 3
REPLACING THE O-RING (P/N 51-112)
REMOVING THE GUARDS (P/N 51-905)

12 13
Lights are strong enough to cause
damage to the human eye.
Do not stare into LEDs for long
periods of time or from a close
range (less than 2 ft).
FoxFury, LLC is not responsible
for any injury or damage caused
during the use of this product.
Usage of this product must be
supervised by an adult when it is
being used by a minor.
Any FoxFury product should
be operated at speeds safe
enough to maneuver around
surrounding obstacles.
Do not use under the influence
of drugs or alcohol.
LIMITED WARRANTY
FoxFury, LLC (“FoxFury”) warrants to
the purchaser of this product (“Buyer”)
that for a period of TWO YEARS
following purchase, this product will
be free from defects in material and
workmanship and will function in
substantial compliance with FoxFury’s
written specifications for this product
as specified in the instruction manual
or on FoxFury’s website located at
www.FoxFury.com. Buyer’s exclusive
remedy shall, in any case, be limited,
at FoxFury’s election, to: A) repair or
replacement of the defective product;
or B) refund of the purchase price for
this product.
THE FOREGOING WARRANTY IS
THE ONLY WARRANTY MADE
BY FOXFURY WITH RESPECT TO
THIS PRODUCT. TO THE EXTENT
ALLOWED BY APPLICABLE LAW,
THERE ARE NO REPRESENTATIONS
OR WARRANTIES OF ANY KIND
WARRANTY AND OTHER
INFORMATION
IPX7
20 M 3 M
PRODUCT DURABILITY
PRODUCT NAME: Taker R40
MODEL NUMBER: 700-331
ADAPTOR INPUT: AC 100-240V,
50/60 Hz
CARE/CLEANING
Your FoxFury product is a professional
tool. Regular maintenance and care of
your light will maximize performance for
you. As needed, wash your FoxFury
product using a soft washcloth, clean
water and a mild soap. Be sure that
both the Light Head and Power Pack
are reassembled securely before
washing. When done, pat dry with a
damp cloth.
AVAILABLE ACCESSORIES
Taker R40 Power Pack
P/N N50-210
Rugo Guards (Top and Bottom)
P/N 51-905
O-Ring Replacement Kit
P/N 51-112
WARNINGS
FoxFury, LLC is not responsible for the
incorrect use of any FoxFury Lighting
product.
When used for extended periods
of time the Rugo™will become
HOT to the touch. Please use care
when operating.
BY THE FOXFURY, EXPRESS OR
IMPLIED, WITH RESPECT TO THE
CONDITION OR PERFORMANCE OF
THIS PRODUCT, INCLUDING, BUT
NOT LIMITED TO, MERCHANTABILITY
OR FITNESS FOR A PARTICULAR
PURPOSE.
THIS LIMITED WARRANTY SHALL
NOT APPLY IF THIS PRODUCT IS
NOT STORED, HANDLED, INSTALLED
OR USED IN STRICT ACCORDANCE
WITH MANUFACTURER’S
SPECIFICATIONS AND INSTRUCTION
MANUALS, OR WHICH HAS BEEN
SUBJECT TO MISUSE, ALTERATION,
NEGLIGENCE OR ACCIDENT.
1. The damaged part or product must
be returned to FoxFury PRIOR TO
any repair or replacement. Shipping
costs are the responsibility of the
claimant.
2. You must obtain a return
authorization (RMA) number from
FoxFury prior to returning products.
FoxFury is not responsible for any
damage incurred while in transit.
3. Buyer will be required to
show proof of purchase—NO
EXCEPTIONS.
4. Any modifications to light, cable or
battery pack automatically voids all
warranties on this product.
All warranty inquiries should be directed
to FoxFury’s Customer Service
Department at [e-mail]
to handle all warranty/repair-related
inquiries.
TO THE EXTENT ALLOWED BY
APPLICABLE LAW: (A) IN NO EVENT,
WHETHER DUE TO BREACH OF
WARRANTY HEREUNDER OR ANY
OTHER CAUSE WHATSOEVER,
SHALL FOXFURY BE LIABLE FOR
OR OBLIGATED IN ANY MANNER TO
PAY CONSEQUENTIAL, INCIDENTAL
OR INDIRECT DAMAGES, INCLUDING,
BUT NOT LIMITED TO, LOSS OF
PROFITS, COST OF SUBSTITUTE
PRODUCTS AND PERSONAL
INJURY OR PROPERTY DAMAGE,
WHETHER SUCH CLAIM IS BASED
ON CONTRACT OR TORT OR ANY
OTHER THEORY OF LAW, AND
(B) FOXFURY’S ONLY DUTIES IN
CONNECTION WITH THE SALE
OF THIS PRODUCT SHALL BE TO
HONOR THE LIMITED WARRANTY
SET FORTH HEREIN. TO THE
EXTENT THAT THIS LIMITED
WARRANTY IS INCONSISTENT WITH
APPLICABLE LAW, THIS STATEMENT
SHALL BE DEEMED MODIFIED
TO BE CONSISTENT WITH SUCH
APPLICABLE LAW.
CONTACT FOXFURY
FoxFury, LLC
Oceanside, CA 92056 USA
Toll-Free: 844-FOXFURY
Tel : [phone]
Fax: [phone]
Email: [e-mail]
Web: FoxFury.com
All FoxFury products are designed in
Oceanside, CA. All FoxFury products
are manufactured with the highest
quality USA and foreign parts. Products
are assembled in either FoxFury’s
controlled plant in Asia or the USA,
under strict quality control.

14 15
NOTES DRILLING TEMPLATE
Use this template to drill the required holes for mounting the Taker R40 to a
riot shield.
1. Begin by cutting this sheet out and taping and centering it (or vertically
aligning it to the desired location).
2. Drill two (2) pilot holes that are 50mm apart using a 1/8" drill bit (use the
smallest circle ( ) as a guide to drill the pilot hole).
3. Using the recommended 12/64" or 7mm drill bit, drill two (2) holes that are
50mm apart (approx 2").
NOTE: Image above is to size and holes are 50mm apart.
1
2
3
INSTRUCTIONS
INSTRUCTIONS:
Use this template to drill the required holes for mounting
the Taker R40 to a Riot shield.
1. Begin by taping this sheet to the shield and centering it (or
vertically aligning it to desired location).
2. Drill two pilot holes that are 50mm apart using a 1/8” drill bit
(use the smallest circle ( ) as a guide to drill the pilot hole).
3. Using the recommended 17/64” or 7mm drill bit, drill two
holes that are 50mm apart (approx 2”).
NOTE: Image above is to size and holes are 50mm apart.
DRILLING TEMPLATE
FOR USE WITH THE TAKER R40 (P/N 700-331)
INSTRUCTIONS:
Use this template to drill the required holes for mounting
the Taker R40 to a Riot shield.
1. Begin by taping this sheet to the shield and centering it (or
vertically aligning it to desired location).
2. Drill two pilot holes that are 50mm apart using a 1/8” drill bit
(use the smallest circle ( ) as a guide to drill the pilot hole).
3. Using the recommended 17/64” or 7mm drill bit, drill two
holes that are 50mm apart (approx 2”).
NOTE: Image above is to size and holes are 50mm apart.
DRILLING TEMPLATE
FOR USE WITH THE TAKER R40 (P/N 700-331)

FOXFURY.COM 5/2017