fox fury TAKER B50 User manual

PRODUCT MANUAL
500-331-G
TAKER B50

3
TAKER B50 REFERENCE GUIDE
LIGHT HEAD
BATTERY COMPARTMENT
(BACK SIDE—PLACED AGAINST SHIELD)
CONNECTING THE BATTERY COMPARTMENT
PROTECTIVE
GUARD
LEDs (4)
3M DUAL
LOCK STRIP
PLACEMENT
KILL SWITCH
CABLE
ENTRY
LOCATION
CLOSING
BUCKLES (4)
TABLE OF CONTENTS
INTRODUCTION
Taker B50 Reference Guide 3
Physical Characteristics & Warnings 4
BATTERY
Battery Installation and Replacement 5
Reassembling the Battery Compartment 5
Battery Life 6
OPERATION
Operational Modes 6
FEATURES
Kill Switch 7
Pressure Switch 7
Heavy Duty Braided Cable 8
Dual Settings 8
Retrofit 8
INSTALLATION
Shield Installation 9
WARRANTY 10–11
CONTACT FOXFURY 11
PRESSURE SWITCH
CONNECTOR
PRESSURE
SWITCH
LIGHT HEAD
CONNECTOR

45
BATTERY INSTALLATION AND REPLACEMENT
1. Open all four (4) of the Battery Compartment Tabs.
2. Insert six (6) CR123 batteries. Reference the plus (+) and minus (-) symbols
located on the inside of the Battery Compartment for proper installation.
REASSEMBLING THE BATTERY COMPARTMENT
1. Once batteries are installed, test the light’s performance by activating the
Power/Mode Switch located on the top of the light.
2. Secure the Battery Compartment Cover by snapping all four (4) Battery
Compartment Tabs. A ‘click’ should be heard as the snaps are shut.
NOTE: Make sure the Battery Compartment is properly closed to
maintain a water tight seal.
PHYSICAL CHARACTERISTICS
Please read below before using the Taker B50 as it relays beneficial operating
and safety information.
SHIELD LIGHT (P/N 500-331-G)
DIMENSIONS (WxH) 5.7” x 2.1” (145 x 53mm)
WEIGHT 21.0oz (595g)
BATTERIES
The Taker B50 uses three (3) or six (6) CR123 batteries. As long as there
are at least three (3) installed, (either on the left or right side) the light will
function.
Using three (3) CR123 batteries decreases the battery life by half, but
does not effect the light intensity.
Mixing of new and used, or different brand batteries is not recommended
as this could lead to leakage or explosion.
1
2
2
1
WARNINGS
Do not stare into LEDs for long periods of time or from a close range
(less than 2 ft (.06m)).
FoxFury’s Turbo-Strobe™is purposely designed to induce disorientation.
Prolonged viewing may produce vertigo or even vomiting.
!
!
1 2
BATTERY
COMPARTMENT
COVER
INCLUDED
3M Dual Lock Strips (P/N 51-030)
Shield Light Cable Clips (P/N 51-031)
Black Cable Sleeve (installed) (P/N 51-035)
Pressure Switch (P/N 35-002)
Square Pressure Switch (P/N 35-009)

67
OPERATIONAL MODES
FEATURES
BATTERY LIFE
MODE BATTERY LIFE LUMENS
MOMENTARY 5hrs 1000
TURBO-STROBE™ 8hrs 1000
CONTINUOUS ON 5hrs 1000
*Battery life may vary according to mode selected, battery quality and prevailing ambient conditions.
For MOMENTARY mode: Press and hold the Power/Mode Switch. While
the Switch is depressed, the light will operate continuously. When the user
removes pressure from the Switch, the light will turn OFF.
For TURBO-STROBE™mode: Press the Power/Mode Switch two (2)
times in rapid succession.
For CONTINUOUS ON: Press the Power/Mode Switch three (3) times in
rapid succession. The light will remain ON.
For OFF or EXIT a mode: Press the Power/Mode Switch once. Then,
continue following the directions above to progress to desired mode.
NOTE: The light does not retain the mode in memory. Once you turn the light
ON, you will have to re-select the mode you desire.
KILL SWITCH
The Taker B50 has a Kill Switch located on the TOP LEFT of the Battery
Compartment. This mechanism is used to shut down or disable the shield light.
PRESSURE SWITCH (INCLUDED)
The Taker B50 includes a Pressure Switch that allows the user to place
it anywhere on the shield. This makes it easier to access the Power/Mode
Switch. The Pressure Switch can easily be attached to the shield via Velcro®or
glue.
To connect the Pressure Switch Connector to the Pressure Switch,
simply confirm alignment, insert the connector, and tighten the Screw
Cap.
To connect the Light Head Connector to the Light Head, simply confirm
alignment, insert the connector, and tighten the Screw Cap.
KILL SWITCH
PRESSURE SWITCH
CONNECTOR
LIGHT HEAD
CONNECTOR
PRESSURE
SWITCH

89
FEATURES (CONT’D)
HEAVY DUTY BRAIDED CABLE
The cable of the B50 is made of steel that protects the internal wiring. The
Black Cable Sleeve (P/N 51-035—included) helps to protect the steel cable
while providing a black covering.
DUAL SETTINGS
The Taker B50 includes two mode settings: the ON/OFF SETTING and the
TACTICAL SETTING. The ON/OFF SETTING simply allows the Light Head to
turn ON and OFF. The TACTICAL SETTING allows you to choose from three
(3) different Operational Modes: Momentary, Continuous On, and
Turbo-Strobe™. The Taker B50 comes in the TACTICAL SETTING.
To change from the TACTICAL SETTING to the ON/OFF SETTING:
With the light turned OFF, press the Power/Mode Switch twice in rapid
succession and hold for 10 seconds. The light should begin to flash. Once
it begins flashing, it is now in the ON/OFF SETTING.
To change from the ON/OFF SETTING to the TACTICAL SETTING:
With the light turned OFF, press and hold the Power/Mode Switch for 10
seconds. The light should begin to go through a slow Turbo-Strobe™ cycle
and then turn OFF. It is now in the TACTICAL SETTING.
RETROFIT
The B50 can retrofit to most ballistic shields without drilling or permanent
modification.
SHIELD INSTALLATION
1. Clean the surface of the shield where the Battery Compartment and Light
Head will be placed.
2. Remove the protective plastic from the back of one of the provided 3M
Dual Lock Strips (P/N 51-030). Place it on the Battery Compartment
Cover (location can be seen in Step 1 of “Battery Installation and
Replacement” on pg. 5). Then, place the Battery Compartment onto the
back of the shield (at desired location) and firmly press down.
3. Remove the protective plastic from the other piece of the Lock Strips and
place it on the back of the Light Head. Then, place the Light Head onto
the front of the shield (at desired location) and firmly press down.
It is recommended that the Light Head is placed on the “upper-center”
portion of the front of the shield, but it can be placed anywhere.
The Battery Compartment should be placed on the back of the shield.
It can be placed anywhere as long as it is on the back of the shield.
Using the Shield Light Cable Clips (P/N 51-031) can help to secure the
Braided Cable of the Light Head.
NOTE: The Pressure Switch also has a provided Lock Strip that allows the
user to place it in desired location.
1
2
3
BALLISTIC
SHIELD
Place the shield in
between the battery
compartment and
Light Head. (The
shield pictured is cut
in half for this visual)
BRAIDED
CABLE
LIGHT HEAD
BATTERY COMPARTMENT

10 11
WARRANTY AND OTHER
INFORMATION
Any FoxFury product should be
operated at speeds safe enough
to maneuver around surrounding
obstacles.
Do not use under the influence
of drugs or alcohol.
LIMITED WARRANTY
FoxFury, LLC (“FoxFury”) warrants
to the purchaser of this product
(“Buyer”) that for a period of two
years following purchase, this product
will be free from defects in material
and workmanship and will function in
substantial compliance with FoxFury’s
written specifications for this product
as specified in the instruction manual
or on FoxFury’s website located at
www.FoxFury.com. Buyer’s exclusive
remedy shall, in any case, be limited,
at FoxFury’s election, to: A) repair or
replacement of the defective product;
or B) refund of the purchase price for
this product.
THE FOREGOING WARRANTY IS
THE ONLY WARRANTY MADE
BY FOXFURY WITH RESPECT TO
THIS PRODUCT. TO THE EXTENT
ALLOWED BY APPLICABLE LAW,
THERE ARE NO REPRESENTATIONS
OR WARRANTIES OF ANY KIND
BY THE FOXFURY, EXPRESS OR
IMPLIED, WITH RESPECT TO THE
CONDITION OR PERFORMANCE OF
THIS PRODUCT, INCLUDING, BUT
NOT LIMITED TO, MERCHANTABILITY
OR FITNESS FOR A PARTICULAR
PURPOSE.
THIS LIMITED WARRANTY SHALL
NOT APPLY IF THIS PRODUCT IS
NOT STORED, HANDLED, INSTALLED
OR USED IN STRICT ACCORDANCE
WITH MANUFACTURER’S
SPECIFICATIONS AND INSTRUCTION
MANUALS, OR WHICH HAS BEEN
SUBJECT TO MISUSE, ALTERATION,
NEGLIGENCE OR ACCIDENT.
PRODUCT DURABILITY
CARE/CLEANING
Your FoxFury product is a professional
tool. Regular maintenance and care of
your light will maximize performance for
you. As needed, wash your FoxFury
product using a soft washcloth, clean
water and a mild soap. Be sure that all
parts are reassembled securely before
washing. When done, pat dry with a
damp cloth.
AVAILABLE ACCESSORIES
Black Cable Sleeve (2)
P/N 51-035
Pressure Switch, P/N 35-002
Square Pressure Switch
P/N 35-009
WARNINGS
FoxFury, LLC is not responsible for the
incorrect use of any FoxFury Lighting
product.
When used for extended periods of
time the light will become HOT to
the touch. Please use care when
operating.
Lights are strong enough to cause
damage to the human eye.
Do not stare into LEDs for long
periods of time or from a close
range (less than 2 ft).
FoxFury, LLC is not responsible
for any injury or damage caused
during the use of this product.
Usage of this product must be
supervised by an adult when it is
being used by a minor.
6 M
1. The damaged part or product must
be returned to FoxFury PRIOR TO
any repair or replacement. Shipping
costs are the responsibility of the
claimant.
2. You must obtain a return
authorization (RMA) number from
FoxFury prior to returning products.
FoxFury is not responsible for any
damage incurred while in transit.
3. Buyer will be required to
show proof of purchase—NO
EXCEPTIONS.
4. Any modifications to light, cable or
battery pack automatically voids all
warranties on this product.
All warranty inquiries should be directed
to FoxFury’s Customer Service
Department at Service@FoxFury.com
to handle all warranty/repair-related
inquiries.
TO THE EXTENT ALLOWED BY
APPLICABLE LAW: (A) IN NO EVENT,
WHETHER DUE TO BREACH OF
WARRANTY HEREUNDER OR ANY
OTHER CAUSE WHATSOEVER,
SHALL FOXFURY BE LIABLE FOR
OR OBLIGATED IN ANY MANNER TO
PAY CONSEQUENTIAL, INCIDENTAL
OR INDIRECT DAMAGES, INCLUDING,
BUT NOT LIMITED TO, LOSS OF
PROFITS, COST OF SUBSTITUTE
PRODUCTS AND PERSONAL
INJURY OR PROPERTY DAMAGE,
WHETHER SUCH CLAIM IS BASED
ON CONTRACT OR TORT OR ANY
OTHER THEORY OF LAW, AND
(B) FOXFURY’S ONLY DUTIES IN
CONNECTION WITH THE SALE
OF THIS PRODUCT SHALL BE TO
HONOR THE LIMITED WARRANTY
SET FORTH HEREIN. TO THE
EXTENT THAT THIS LIMITED
WARRANTY IS INCONSISTENT WITH
APPLICABLE LAW, THIS STATEMENT
SHALL BE DEEMED MODIFIED
TO BE CONSISTENT WITH SUCH
APPLICABLE LAW.
CONTACT FOXFURY
FoxFury, LLC
Oceanside, CA 92056 USA
Toll-Free: 844-FOXFURY
Tel : 760.945.4231
Fax: 760.433.3650
Email: Service@FoxFury.com
Web: FoxFury.com
All FoxFury products are designed in
Oceanside, CA. All FoxFury products
are manufactured with the highest
quality USA and foreign parts. Products
are assembled in either FoxFury’s
controlled plant in Asia or the USA,
under strict quality control.
IPX7
3 M

FOXFURY.COM 5/2017
This manual suits for next models
1
Table of contents
Other fox fury Flashlight manuals