FoxAlien Masuter Pro User manual

Please read this manual carefully before using.
Desktop
CNC Router
M a s u t e r P r o
USER MANUAL

Catalog
Warranty & Disclaimer
Product Specifications
How to Assemble the Machine
Wiring Diagrams
•XYZ Stepper Wiring Diagrams
•XYZ Limit Switch Wiring Diagrams
•Spindle & Light Wiring Diagrams
Controller Instructions
How to Install the Router Bit
How to Use Grblcontrol (Candle)
•Driver Installation
•Grblcontrol (Candle) Working Interface Introduction
Make Your First Cut
How to Unlock Limit Switch
How to Use E-stop
Z-Probe Operating
ExtendedAccessories
•Offline Controller
•Laser Module
•300W Spindle
1
2
3
15
16
17
18
19
20
20
21
22
24
15
25
26
27
27
27
28

Warranty & Disclaimer
Please be careful when using your CNC machine. This machine is an electrical device with
moving parts and dangerous areas.
•This CNC Machine is for Indoor Use Only.
•Wear the proper protection equipment while operating.
•Always place the CNC Machine on a stable surface.
•Never disassemble the Power Supply or Electrical Components. This may cause damage and will VOID the
warranty.
•DO NOT TOUCH the machine spindle, or place any part near the working area when the machine is operating.
DO NOT leave children unsupervised with the CNC Machine even when it’s not operating. Injury may occur.
•DO NOT leave the machine unattended while it's operating.
One Year Warranty
•This product is warranted against any defective material or workmanship for a period of twelve months from
date of delivery.
•Any parts determined by the manufacturer to be defective will be replaced in whole or part as determined by
the manufacturer, but no labor costs or other claims for damages will be allowed.
-1-

Model Masuter Pro
Working Area 400 x 400 x 60mm (15.75” x 15.75” x 2.36”)
Input Voltage 12V
Input Current 5A
Spindle Power 60W
Spindle Speed 10000 r/min
Motor NEMA17
Firmware Version 1.1H
Limit Switch X, Y, Z
Emergency Stop Button Yes
Support OS Windows XP, Windows 7, Windows 8, Windows 10, Windows 11, Linux,
Mac OS
Software Grblcontrol(Candle), other GRBL compatible software
Offline Working Supports offline working, offline control sold separately
Support Add-ons Laser, Offline controller, 300W Spindle& Trimmer (NOT included)
Product Specifications
-2-

4X-axis Aluminum Profile 20 M5*20 Flat Cap Bolt
2x
1
How to Assemble the Machine
-3-
2 Y-axis Aluminum Profile (R)
1Y-axis Aluminum Profile (L)
Y1
Y2
8x

8x
2
How to Assemble the Machine
-4-
17 M5*20 Bolt5MDF Spoil Board

4x
3
How to Assemble the Machine
-5-
19 M5*16 Flat Cap Bolt3X-axis Gantry

4x
4
How to Assemble the Machine
-6-
16 M5*12 Bolt 23 Washer6 Spindle Holder
4x

5
-7-
7 Spindle
How to Assemble the Machine

4x
6
-8-
13 Y-axis Drag Chain Bracket
21 M3*6 Button Cap Bolt
12 Y-axis Drag Chain Bracket
How to Assemble the Machine

7
-9-
14 X-axis Drag Chain Bracket
2x
21 M3*6 Button Cap Bolt
How to Assemble the Machine

2x
8
-10-
8 Controller Support Plate 22 M3*8 Button Cap Bolt9 Controller
How to Assemble the Machine

9
-11-
24 M5 T-nut15 M5*8 Bolt
2x 2x
How to Assemble the Machine

10
-12-
25 Hex Wrench
How to Assemble the Machine

4x
11
-13-
18 M4*6 Flat Cap Bolt11 Y Axis Drag Chain
How to Assemble the Machine

-14-
4x
12 18 M4*6 Flat Cap Bolt11 Y Axis Drag Chain
How to Assemble the Machine

-15-
- X, Y & Z Stepper Motors Wiring Diagrams
Wiring Diagrams

-16-
- X, Y & Z Limit Switches Wiring Diagrams

-17-
- Spindle & Light Wiring Diagrams
Positive wire (Red) connects to the port with red dot
Negative wire (Blue) connects to the other port
Light: Insert the plug to the socket
60W spindle plugged into Spindle 1 socket
Flip the toggle switch to the right side

-18-
Controller Instructions
24-48V DC Input
Light On/Off
USB Interface
Offline Controller Interface
12V DC Input
300W Spindle Interface(Spindle2)
60W Spindle Interface(Spindle1)
Laser Interface
Toggle Switch
Flip to the left when using 300W Spindle
Flip to the right when using 60W Spindle or Laser
Toggle Switch：
Home Button
Power Button
Emergency Stop Button