Foxtech EH30-MTIR User manual

User Manual
V1.0
EH30-M TIR Dual Sensor 30X
Optical Zoom Camera with 3-axis
Gimbal
2022.02

Thank you for purchasing this product. This is a special web page for gimbal and cameras, you can enter
this page for the latest product information, technical support and user manuals.
https://www.foxtechfpv.com/industrial-drone/camera-for-drones.html
We recommend that you download and use the latest user manual. And no further update notice will be
given separately. Due to different production batches, the appearance or function parameters are slightly
different, which does not affect the normal use of the product.
Please read this statement carefully before use. Once used, it is deemed to be an endorsement and
acceptance of the entire contents of this statement. Please read the instruction manual carefully and
strictly follow the requirements of this manual to install and use this product. Foxtech will not bear any legal
responsibility for any results or losses caused by improper use, installation, final assembly and modification
by users.
Note
Disclaimer
Intellectual Property Rights
The intellectual property rights of this product and manual are owned by Foxtech Trade Co., Ltd. Without
written permission, no organization or individual may copy, reproduce or distribute in any form. If quotation is
needed, the source must be indicated, and this manual must not be modified, deleted or quoted against its
original intention.

©2020 FOXTECH All Rights Reserved 1
Note
Disclaimer
Intellectual Property Rights
System Composition
Product System Atlas
Installation
Installation and setup methods of third-party videolink
GCS Software Usage Instructions
Operating Pods
Frequently Asked Questions
Parameter
2
2
2
2
2
3
4
8
8
10
10
Contents

©2020 FOXTECH All Rights Reserved 2
System Composition
Product System Atlas
Product Wiring Diagram

©2020 FOXTECH All Rights Reserved 3
Foxtech EH30-MTIR Dual Sensor 30X Optical Zoom Camera User Manual

©2020 FOXTECH All Rights Reserved 4
A. Modify IP of Pod and IDU (segment to meet videolink requirements)
Pod segment modification, take “change 42 segment to 1 segment” as an example:
1→pod electrified, and connected the pod to the computer through the wire, the pod works normally after
about 15 seconds, the computer recognizes the camera network.
2→TCPIPV4 settings, as shown below, are saved after confirmation
3. Use GCS ground station for gateway setting
Click to search device, then double-click the pop-up IP bar, save it after modification, and restart the gimbal.
Installation and setup methods of third-party videolink
192 168 42 10
255 255 255 0
192 108 42 0

©2020 FOXTECH All Rights Reserved 5
4.→Camera IP modification
Open any browser, enter 192.168.42.108
After entering the following interface, username, password are admin
Confirmation

©2020 FOXTECH All Rights Reserved 6
Then the following password modification interface appears, click cancel
After entering the setup interface, click Settings → Network Settings → General Settings
Change the IP address and default gateway “42” to “1”, then click Save.
Do not modify the password, otherwise the software will not working properly.

©2020 FOXTECH All Rights Reserved 7
5.→Pod net segment setup complete.
Change the network segment settings in the computer TCPIPV4 to the normal network segment. (Different
videolink requires different settings, the equipment used shall prevail.)
Pod RTSP Common Address:
Main stream rtsp ://admin: admin @< ip >:554/cam/realmonito? Channel=1& subtype=0
Secondary stream 1 rtsp ://admin: admin @< ip >:554/cam/realmonito? Channel =1& subtype =1
Secondary stream 2 rtsp ://admin: admin @< ip >:554/cam/realmonito? Channel=1& subtype=2
usually uses secondary stream 2 for preview
RTSP ://admin: admin @192.168.42.108:554/cam/realmonito? Channel=1& subtype=2

©2020 FOXTECH All Rights Reserved 8
Setting area
Interface shifting
Camera setting
photo
REC
One key downward
One key forward
Yaw following
Manual focus+
Auto focus
Manual focus-
Target following
GCS Software Usage Instructions
Operating Pods
GCS pod software through the mouse, virtual keys, USB joystick to achieve the full operation of the pod.

©2020 FOXTECH All Rights Reserved 9
Operating Pods
gcs support remote real-time download of camera side video, photos.
1. Operational steps
view → download interface (as shown below) can download video (MP4 style), photo (jpg) offline. And the
photos support real-time preview.
Photo preview window
Download type switch

©2020 FOXTECH All Rights Reserved 10
Frequently Asked Questions
No Image
Hardware checking:
pod power supply is normal, pod and idu module are properly connected. The pod works properly.
Datalink (sky end, ground end) power supply is normal. The datalink sky end is properly connected to the
IDU module, and the connection wire is not broken. The datalink ground end and the computer is connected
normally, the network wire does not have the damage to break the circuit.
Software setup check:
Make sure the computer network is set correctly and the computer turns off the wifi when connecting the
datalink. The computer is not connected to any network other than the data link.
Software network IP address is incorrect :(when the gimbal, camera IP address changes, need to
synchronously modify this software IP)
Open GCS software → network settings
Modify the IP address.

Environment parameters
Operatingtemperature -20°C~60° C
Storethetemperature -40°C~80°C
Theg i m bal
Control accuracy ±0.008°
Rotation Range Pitch:70to-90degrees; Yaw: 360°
Mechanical range Pitch:75to-100 degrees; Yaw: 360°
Smart Target tracking Support
Cameraparameters
visible light
sensor CMOS:1/2.8″; Totalpixels2.16 Mega
l e n s
30x opticalzoom
l e n s F: 4.7to141mm
©2020 FOXTECH All Rights Reserved 11

Minimum shooting distance: 1mto1.5m
(near-focus-far-focus)
field-of-view angle(horizontal):
60to2.3degrees
Thei m a g e s t o r a g e format JPEG
V i de o s t o r a g e format MP4
Theworkingmode V i d e o ; Takingpictures;
Throughthefog Electronic fogging
Exposuremode A u t o exposure
Theencoding resolution
Main s t r e a m : 25fps (1920×1080, 1280×720)
Secondarys t r e a m s : 25fps (1920×1080, 1280×720, 704×
576, 352×288）
2Dn o i s e reduction Support (auto-on)
3Dn o i s e reduction Support (auto-on)
Electronic shutter 1/3to1/30000 s e c o n d s
exposure A u t o m a t i c mode;
I n f o V i d e o Overlay(OSD) Support
Pointtozoom Support
©2020 FOXTECH All Rights Reserved 12

Pointtothezoom range 1to30timesoptical
One-click zoom to 1X
image
Support
Thermalimaging
Detector performance
Type VOx Uncooled infrared focalplanedetector
Cells p a c i n g 12microns
R e s p o n d totheband 8to14microns
sensitivity ≤50mk@25℃，F#1.0
Therangeoftemperature
measurements
Two-speed: -20℃to150 ℃default ,
0℃to550 ℃
Temperature
measurement accuracy
± 3℃ or3%ofthe ±readings(takelarger) and
theambienttemperature i s -20℃to60℃
Temperature
measurement tool
Point,line, areaanalysis
focall e n g t h 19mm fixedfocus
©2020 FOXTECH All Rights Reserved 13

Main s t r e a m : 25fps
(704×576)
Secondarys t r e a m : 25fps
(704×576,640x512)
Theencoding resolution
This content is subject to change.
Download the latest version from
https://www.foxtechfpv.com/eh30-m-tir-gimbal-camera.html
For everyday updates, please follow Foxtech facebook page"Foxtechhobby".
YouTube Channel: Foxtech
©2020 FOXTECH All Rights Reserved 14