Franke AQUA741 User manual

Installation and operating instructions Istruzioni per il montaggio e l’uso
Notice de montage et de mise en service Montage- en bedrijfsinstructies
Instrucciones de montaje y uso
ZMI_001_2000103155-AQUA741_#SALL_#AQU_#V1.fm/17.10.12
Franke Aquarotter GmbH, Germany
EA-Nr.: 7612982173691
FAR-Best.-Nr.: 3380 02 20
AQUA741
EA-Nr.: 7612982173707
FAR-Best.-Nr.: 2000103159
AQUA742
EA-Nr.: 7612982173912
FAR-Best.-Nr.: 2000103157
AQUA747
EA-Nr.: 7612982173929
FAR-Best.-Nr.: 2000103161
AQUA748
DE
EN
FR
ES
IT
NL

2
Inhaltsverzeichnis35_01.fm
...................................................................................... 3
Please refer to the graphics in the German Installation and
Operating Instructions.
...................................................................................... 13
Les graphiques sont disponibles dans la notice de montage et de
mise en service allemande.
...................................................................................... 24
Por favor, consulte los gráficos en las instrucciones alemanas de
montaje y uso.
...................................................................................... 35
Per le grafiche fare riferimento alle Istruzioni per il montaggio e
l’uso in tedesco.
...................................................................................... 46
De tekeningen kunt u in de Duitse montage- en bedrijfsinst-
ructies vinden.
EN
FR
ES
IT
NL

3
ZMI_001_2000103155-AQUA741_#SEN_#AQU_#V1.fm
0English
AQUAMIX cast mineral shower panel with DN 15 self-closing single mixer tap
AQUA741
AQUA742 ................... with tray for shower gel
AQUA747 ................... with shower pipe emptying
AQUA748 ................... with shower pipe emptying and tray for shower gel
Please refer to the graphics in the German installation and operating instructions.
0Table of contents
1. Abbreviations and units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. Important notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Description of product
5. Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
6. Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
7. Properties of MIRANIT-S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
8. Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
9. Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
10. Installation example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Assembly, function and commissioning
12. Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
13. Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
14. Adjusting the flow time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
15. Adjusting the temperature limits. . . . . . . . . . . . . . . . . . . . . . . . . . 8
Maintenance
16. Maintenance and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
17. Maintenance information for MIRANIT-S . . . . . . . . . . . . . . . . . . . 9
18. Replacing the filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
20. Replacing the flow rate regulator . . . . . . . . . . . . . . . . . . . . . . . . . 10
21. Replacing the non-return valve. . . . . . . . . . . . . . . . . . . . . . . . . . . 11
22. Replace the functional element . . . . . . . . . . . . . . . . . . . . . . . . . . 11
23. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
24. Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
EN

4
ZMI_001_2000103155-AQUA741_#SEN_#AQU_#V1.fm
1. Abbreviations and units
2. Key
Warning!
Failure to observe can result in bodily injury or even death.
Caution!
Failure to observe can result in material damage.
☞Important!
Failure to observe can cause the product to malfunction.
☞Useful information for optimum handling of the product.
3. Warranty
Liability is accepted in accordance with the General Terms and Conditions of
Business and Supply.
Use only genuine spare parts!
4. Important notes
• Installation, commissioning and maintenance are to be performed only by a
qualified expert in accordance with the provided instructions, legal requirements
and the recognised engineering standards.
• All technical connection regulations specified by the local water and electricity
supply companies must be observed.
• We reserve the right to make changes.
EA-Nr. European article number
FAR-Best.-Nr. Franke Aquarotter order number
Conversion 1 mm = 0.03937 inches
1 inch = 25.4 mm
All length specifications in the graphics are in mm.

5
ZMI_001_2000103155-AQUA741_#SEN_#AQU_#V1.fm
5. Application
AQUAMIX shower panel made of mineral material for wall mounting for connection
to hot and cold water. Adjustable flow time. Alternatively with automatically emptying
shower pipe.
6. Technical specifications
7. Properties of MIRANIT-S
MIRANIT-S resin-bound mineral material is a mixture of aluminium trihydrate,
natural stone, high quality unsaturated polyester resin and colour pigments.
MIRANIT-S ensures high stability and breaking resistance.
The smooth, non-porous and semi gloss surface is very easy to clean and fulfils the
most stringent hygiene requirements.
8. Scope of delivery
9. Dimensions
Minimum flow pressure: 1.5 bar
Recommended flow
pressure:
1-5 bar
Maximum operating
pressure:
10 bar
Calculated flow rate: 0.15 l/s 0.15 l/s
Volumetric flow: 0.20 l/s at a flow pressure of 3 bar
Flow time at 38°C 1–50 s adjustable at shower head 0.20 l/s
Quantity Name
1 Shower panel with:
Mixer, lockable water volume regulators, connection
hoses and AQUAJET Slimline shower head
2 Connection bracket
1 Suspension rail
1 0.15 l/s flow rate regulator
3 Screws, wall plugs
1 Installation and operating instructions

6
ZMI_001_2000103155-AQUA741_#SEN_#AQU_#V1.fm
10. Installation example
11. Spray pattern
12. Assembly
Warning!
Only operate the fitting with non-return valves and the specified filters.
Failure to observe this instruction can result in an increased germ load in the
drinking water and thus pose a health or mortality risk.
☞Important!
Prior to the assembly process, flush the pipework in accordance with DIN 1988.
☞To protect the tiles, use masking tape when marking and drilling. Drill at low speed.
☞Depending on the composition of the wall, special wall plugs may have to be used
(to be provided by the customer).
Fig. A:Water connection from above
Fig. B: Water connection from the rear
12.1 Only for water connection from the rear: Install the connection brackets (a) leak-tight.
12.2 Screw in the water volume regulators (b) leak-tight.
12.3 Align the water volume regulators so that the locking screw and operating element
are freely accessible.
12.4 For a shower head height of 2.10 m to 2.30 m, mark drill holes for installation at a
height (c) of 2.12 m to 2.32 m from the top of the finished floor.
12.5 Drill holes in accordance with these markings.
12.6 Insert the wall plugs.
12.7 Screw on the suspension rail.
12.8 Suspend the shower panel.
12.9 Mark the remaining drill hole.
12.10 Remove the shower panel.
12.11 Drill hole in accordance with the marking.
12.12 Insert the wall plug
12.13 Only for water connection from the rear: Prioritise work steps 12.15 to 12.17.
12.14 Mount the shower panel on the suspension rail and screw tight.
12.15 Establish the water connections.
12.16 Open the water volume regulators using an Allen key.
d: closed
e: open
12.17 Check the water connections for leaks.

7
ZMI_001_2000103155-AQUA741_#SEN_#AQU_#V1.fm
13. Function
Trigger the flow of water
13.1 Press the pressure cap.
• The water will flow.
• The water flow stops automatically once the preset flow time has expired.
☞The flow time is adjustable from 1 - 50 seconds.
Temperature selection
14. Adjusting the flow time
14.1 Set the desired temperature of the mixed water.
14.2 Using a screwdriver, carefully take off the stopper.
14.3 Remove the stopper.
14.4 Release the grub screw with an Allen key.
14.5 Remove the pressure cap.
14.6 Use a screwdriver to set the flow time.
a: Blade width 3 mm
+ longer flow time (max. 50 s)
– shorter flow time (min. 1 s)
14.7 Trigger the fitting to measure the flow time.
☞Important!
When putting the pressure cap in place, ensure that the tappet engages with the
corresponding groove.
14.8 Once the desired flow time has been set, put the pressure cap in place.
14.9 Reassemble in reverse order.

8
ZMI_001_2000103155-AQUA741_#SEN_#AQU_#V1.fm
15. Adjusting the temperature limits.
Warning!
If the hot water supply temperature is above 45°C, the - temperature limit should be
adjusted.
Failure to observe this instruction can result in injuries due to scalding.
☞The temperature limit is not an active scald protection.
15.1 Remove the pressure cap (see Chapter 14.).
15.2 Carefully lever off the stop ring with a screwdriver and pull off the gear teeth by hand.
15.3 Put the pressure cap in place and trigger the fitting.
15.4 Turn the pressure cap until the desired maximum water temperature is reached.
15.5 Slide the stop ring onto the gear teeth so that the stud on the stop ring is at the right-
hand end stop of the housing.
☞Important!
When putting the pressure cap in place, ensure that the tappet engages with the
corresponding groove (see Chapter 14.).
15.6 Reassemble in reverse order.
16. Maintenance and care
The fitting must be checked and maintained at regular intervals depending on the
water quality and in accordance with the local conditions and rules and regulations
applicable at the site.
Maintain the following components:
• Shower head (see Chapter 20.)
• Filters (see Chapter 18.)
• Non-return valve (see Chapter 21.)
Use suitable cleaning agents which do not attack the fitting in a proper manner and
rinse with water after use. High-pressure cleaners must not be used for cleaning.
Removing the shower panel
For some maintenance tasks, the shower panel must be removed.
Caution!
Do not allow the shower panel to hang by the connecting hoses.
Water connection from above:
16.1 Close the water volume regulators.
a: closed
b: open
16.2 Trigger the fitting.

9
ZMI_001_2000103155-AQUA741_#SEN_#AQU_#V1.fm
16.3 Disconnect the water supply.
16.4 Release the screws on the shower panel.
16.5 Unhook the shower panel.
16.6 Insert the side of the shower panel into the suspension rail.
Water connection from rear:
16.7 Release the screw on the shower panel.
16.8 Unhook the shower panel.
16.9 Insert the side of the shower panel into the suspension rail.
16.10 Close the water volume regulators (see Work step 16.1).
16.11 Trigger the fitting.
16.12 Disconnect the water supply.
17. Maintenance information for MIRANIT-S
Soap cleaners with a neutral pH-value are sufficient for cleaning and care. Apply the
cleaner with a soft, clean cloth, leave to soak briefly and then rinse with a large
volume of water.
Caution!
The following must not be used:
• Cleaning agents with an abrasive effect
• Cleaning sponges / cleaning cloths with an abrasive effect
• Steel wool or other hard objects
• Solvents
☞Important!
Any minor damage to the surface, e.g. small scratches, can be directly polished out.
A repair kit is available for larger damaged areas. The surface is polished with Type
1000 grinding paper after application and drying of the repair material.

10
ZMI_001_2000103155-AQUA741_#SEN_#AQU_#V1.fm
18. Replacing the filters
Water volume regulator filters
18.1 Close the water volume regulators (see Work step 16.1).
18.2 Unscrew the locking screws (a) on the water volume regulators.
18.3 Replace the filters (b).
☞Important!
Note the installation position of the filters.
18.4 Reassemble in reverse order.
19. Cleaning the shower head faceplate
19.1 Release the screw using an Allen key.
19.2 With a screwdriver, carefully lever out the spray faceplate.
19.3 Clean the shower head faceplate.
19.4 Reassemble in reverse order.
20. Replacing the flow rate regulator
20.1 Release the grub screw with an Allen key.
20.2 Pull the shower head out of the connection spigot.
20.3 Remove the locking ring on the inside using appropriate pliers for locking rings.
20.4 Pull out the flow rate regulator using flat-nosed pliers.
20.5 Replace the flow rate regulator. Observe the table.
☞Important!
Note the installation position of the flow rate regulator. The struts must point towards
the shower head.
20.6 Insert the flow rate regulator and secure with the locking ring.
a: Struts
b: Direction of flow
20.7 Slide the shower head onto the connection spigot.
20.8 Tighten the grub screw with an Allen key.
Flow rate Flow rate regulator
0.15 l/s (orange) FAR-Best.-Nr. 2000104782
0.20 l/s (red) FAR-Best.-Nr. 2000104783