Franke FF 5000 SERIES User manual

FF 5000 SERIES
Revolving mixer with separate handshower
Installation guide

2
ENGLISH
PARTS LIST
G 1156 Cartridge
G R0239.XX Ring cap
G 13396.XX Handle
G 1399.XX Aerator
G 1402.XX Side spray
G 28900.XX Hook for side spray
G R0185 Fastening set (rubber washer, metal washer, nut)
G 1697 Priority water flow system
G 1403 Flexible hose of the side spray
G 1404 Flexible hose
G 1635 Counter weight
G R1190 Fastening set (rubber washer, triangular flange, metal washer, nut, allen key
2,5mm)
TECHNICAL FEATURES
Maximum water flow 2.2 gpm - 60 psi
Recommended pressure range 15-75 psi - Over 75 psi PRV required
Complies with Proposition 65, NSF61, UPC and C-UPC requirements
G 1402.XX
G R0185
G 1399.XX
G 13396.XX
G R1190
G 1635
G 1403
G 1404
G R0239.XX
G 1156
G 28900.XX
G 1697

3
ENGLISH
Faucet installation
Please remove all components from package and inspect prior to
installation (see itemized table and picture).
NOTE:
Call us immediately if you see inconsistencies. (1-800-626-5771)
or visit
www.frankeksd.com
TABLE OF CONTENT
1 Faucet
2 Flexible hose of the side spray
3 Hook for side spray
4 Side spray
5Priority water flow system
6 Fastening set (rubber washer, metal washer, nut)
7 Fastening set (rubber washer, triangular flange, metal washer, nut, allen key 2,5mm)
8 Counter weight
Remove all mounting hardware from protecting plastic bag.

4
ENGLISH
Set the faucet into place on the sink as indicated in the figure.
NOTE:
the rubber O-ring should be sitting on top of the countertop and between
the faucet body. DO NOT use putty or other sealant at this location.
Install faucet to the sink or countertop

5
ENGLISH
Install faucet to the sink or
countertop - follows
Install the fastening components to the faucet’s threaded shank in
the following sequence: round gasket (1), triangular flange (2), metal
washer (3) and threaded nut (4) (the triangular flange can be omitted
if the sink/countertop is too thick). Install the fastening items of the
spray head holder in the following sequence: the flat rubber washer
(5), the metal washer (6) and the threaded nut (7).
1
2
3
4
5
6
7

6
ENGLISH
Assembly of side spray and connecting of the
priority water flow system
Proceed to the connection of the flexible hose of the side spray (A)
and the priority water flow system (B - follow the phases indicated).
Interposing the holding gaskets within the connections as indicated
in the figure. Fix the lead counter weight to the flexible hose of the
side spray at a distance of approx. 40 cm from the connection to the
outlet pipe.
filter washer
A
~ 40 cm
1
2
B
3

7
ENGLISH
Connect the supply lines
Connect the hot and cold supply lines. Do not allow the supply
tubes to twist or bend sharply. Leave the valves closed.
- Move the faucet handle by rotating it onwards so that it opens in
the full hot position and open the hot supply for 15 seconds. Close
the hot supply.
- Move the faucet handle by rotating it backwards so that it opens in
the full cold position and open the cold supply for 15 seconds. Clo-
se the cold supply.
- Move the faucet handle to the off position.
Arrow BLU
COLD water
Arrow RED
HOT water

8
ENGLISH
F
G
D
EC
A
B
Replacing the cartridge
Before starting, shut off the water supply to the faucet and move the
faucet handle to the off position. Use a 2.5 mm Allen key to loosen
the set screw (A) which is accessible from the back of the handle. Lift
the handle (B) from the cartridge (F). Find the small notch at the base
of the chrome ring cap and carefully pry up against this to remove the
cap (C). Remove the brass retaining ring (E) using a 28 mm wrench.
Lift out the cartridge (F). Ensure that the grommets (O-rings) are in
good condition and properly seated and remove all mineral deposits.
Install the new cartridge so that the central pivots fit into the corre-
sponding seats.
F
G
D
EC
A
B
28 mm wrench
Allen key 2.5 mm

9
ENGLISH
Cleaning of the aerator
It is recommended that you periodically clean the aerator of your fau-
cet. To do so, unscrew the aerator holder from its own seat. Simply
using a toothbrush, or something similar, rub the filter under the wa-
ter, removing the impurities and any build up. Screw the areator back
into place.
1
2
Cleaning of the side spray
Any deposits which may accumulate on the nozzle can be removed
by simply running a finger over the rubber extrusions and then run-
ning the water for a few seconds. In extreme cases this step may have
to be repeated.

10
ENGLISH
General maintenance
Clean aerator periodically.
Do not use harsh detergents, solvents, chemical agents, metallic
sponges, etc. that could harm the surface.
Clean only with a soft sponge and soapy water.
Clean and then dry properly the faucet in case of very hard or calcare-
ous water, whose deposits cold damage the surface.