Franke AQUACONTACT AQCT0025 User manual

Installation and operating instructions Montażi instrukcja obsługi
Notice de montage et de mise en service Monterings- og driftsvejledning
Instrucciones de montaje y uso Návod pro montáž a provoz
Istruzioni per il montaggio e l’uso Asennus- ja käyttöohje
Montage- en bedrijfsinstructies Инструкция по монтажу ивводу в
эксплуатацию
ZMI_001_2000103793-AQCT0025_#SALL_#AQU_#V1.fm/16.07.15
Franke Aquarotter GmbH, Germany
EA-Nr.: 7612982181948
FAR-Best.-Nr.: 2000103793
AQCT0025
DE
EN
FR
ES
IT
NL
PL
SV
CS
FI
RU

2
Inhaltsverzeichnis35.fm
...................................................................................... 3
Please refer to the graphics in the German Installation and
Operating Instructions.
...................................................................................... 12
Les graphiques sont disponibles dans la notice de montage et de
mise en service allemande.
...................................................................................... 21
Por favor, consulte los gráficos en las instrucciones alemanas de
montaje y uso.
...................................................................................... 31
Per le grafiche fare riferimento alle Istruzioni per il montaggio e
l’uso in tedesco.
...................................................................................... 40
De tekeningen kunt u in de Duitse montage- en bedrijfsinstructies
vinden.
...................................................................................... 49
Prosimy przyjąć grafikęz niemieckiej instrukcji montażu i obsługi.
...................................................................................... 58
Bilderna finns i den tyska monterings- och bruksanvisningen.
...................................................................................... 67
Obrázky najdete v nìmeckém návodu k montáži a obsluze.
...................................................................................... 77
Kuvat löydätte saksankielisestä asennus- ja käyttöohjeesta.
...................................................................................... 86
Рисунки приведены винструкции по монтажу иэксплуатации на
немецком языке.
EN
FR
ES
IT
NL
PL
SV
CS
FI
RU

3
ZMI_001_2000103793-AQCT0025_#SEN_#AQU_#V1.fm
0English
AQUACONTACT - Shower battery - installation kit, 6 V DC
Please refer to the graphics in the German installation and operating instructions.
0Table of contents
1. Abbreviations and units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. Important notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Description of product
5. Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
6. Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
7. Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
8. Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
9. Installation example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Assembly, function and commissioning
10. Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
11. Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
12. Adjusting the flow time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
13. Adjusting the range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
14. Hygiene flush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
15. Thermal disinfection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
16. Adjusting the cleaning switch-off . . . . . . . . . . . . . . . . . . . . . . . . . 9
Maintenance
17. Maintenance and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
18. Replacing the filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
19. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
20. Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
EN

4
ZMI_001_2000103793-AQCT0025_#SEN_#AQU_#V1.fm
1. Abbreviations and units
2. Key
Warning!
Failure to observe can result in bodily injury or even death.
Caution!
Failure to observe can result in material damage.
☞Important!
Failure to observe can cause the product to malfunction.
☞Useful information for optimal handling of the product.
3. Warranty
Liability is accepted in accordance with the General Terms and Conditions of
Business and Supply.
Use original spare parts only!
DN Nominal diameter in mm
RCD Residual current protective device,
earth leakage circuit breaker
SELV Safety extra low voltage
EA-Nr. International article number
FAR-Best.-Nr. Franke Aquarotter order number
Conversion 1 mm = 0.03937 inches
1 inch = 25.4 mm
All length specifications in the graphics are in mm.

5
ZMI_001_2000103793-AQCT0025_#SEN_#AQU_#V1.fm
4. Important notes
• Installation, commissioning and maintenance are to be performed only by a
qualified expert in accordance with the provided instructions, legal requirements,
and the recognised engineering standards.
• All technical connection regulations specified by the local water and electricity
supply companies must be observed.
• The battery compartment with battery or power supply with extension cable must
be ordered separately (see Accessories, Chapter 20).
• All work must be carried out in a de-energised state.
• We reserve the right to make changes.
5. Application
AQUACONTACT - DN 15 shower fitting for wall mounting with electronic time control
for battery or mains operation. For connection to premixed hot water or cold water.
30 second flow time.
Installation kit with integrated hygiene flush (24h after last actuation, for 10s).
Functions which can be activated via reflection code on sensor: Activation/deacti-
vation of hygiene flush and cleaning switch-off (3 min.).
Additional functions via optional remote control
– Setting the flow and interval times
– Switch from time control to body reflection, maximum flow time of 300 seconds
– Program-controlled thermal disinfection with safety switch-off
6. Technical specifications
Minimum flow pressure: 1.0 bar
Recommended flow
pressure:
1-5 bar
Maximum operating
pressure:
10 bar
Calculation of flow rate: 0.20 l/s
Volumetric flow: 0.50 l/s at a flow pressure of 3 bar
Flow time at 38°C 1–50 s adjustable on shower head 0.20 l/s
Operating voltage: 6 VDC
Power consumption: 1.5 W
Protection class: IP 67

6
ZMI_001_2000103793-AQCT0025_#SEN_#AQU_#V1.fm
7. Scope of delivery
8. Dimensions
9. Installation example
10. Assembly
Warning!
Only operate the fitting with non-return valves and the specified filters.
Failure to observe this instruction can result in an increased germ load in the
drinking water and thus pose a health or mortality risk.
Warning!
• Operate the product only with safety extra low voltage (SELV). The components
do not have to be earthed.
• Secure the electrical connection with a residual current circuit breaker (RCD).
Failure to observe this instruction can result in death or material damage due to
electric shock or fire, for example.
☞Important!
Prior to the assembly process, flush the pipework in accordance with DIN 1988.
10.1 Remove the wall protection.
10.2 Use a hexagonal wrench to close the water volume regulators.
a: closed
b: open
☞Important!
When removing the cap nut, use an open-ended wrench to hold the water volume
regulator (c).
10.3 Remove the flush connector (c).
10.4 Remove the existing seals.
10.5 Insert the solenoid valve (d) with new seals.
10.6 Open the water volume regulators (see step 10.2).
10.7 Fit the frame (e) in a horizontal position.
10.8 Where necessary, shorten the spacer sleeves (f) to the distance between the front
edge of the wall unit and the front edge of the tiles.
Simplified drawing without fitting
☞Important!
The solenoid valve must be connected before the power supply is connected.

7
ZMI_001_2000103793-AQCT0025_#SEN_#AQU_#V1.fm
10.9 Connect the solenoid valve to the AQUACONTACT sensor.
☞The battery compartment or power supply and extension cable are not part of the
scope of delivery (see Accessories, chapter 20).
☞If you are using a wall-mounted power supply unit, it must be installed around 3 m
away from the shower.
10.10 Connect the AQUACONTACT sensor (g) to
– a battery compartment (h)
or
– a wall-mounted power supply unit (k).
☞If the battery charge state is low, the LED flashes in a 20 second cycle.
10.11 Remove the protective film from the shower panel.
10.12 Seal the shower panel (e.g. with Chromol, not part of the scope of delivery,
see Accessories, chapter 20).
10.13 Insert the top of the cover plate (l) into the frame tabs and fit.
10.14 Fasten the cover plate at the bottom, using screws (m).
10.15 Check the flow time and adjust where necessary (see chapter 12.).
11. Function
☞You can switch between time control and body reflection using the remote control
(not in the scope of delivery; see Accessories, chapter 20)
Time control
Triggering the flow of water
11.1 Hold your hand near the sensor.
• The water will flow.
• The water flow will stop automatically
– once the preset flow time expires
or
– after approaching the sensor once again.
☞The flow duration is factory-set to 30 seconds.
Body reflection
Triggering the flow of water
11.2 Hold your hand near the sensor.
• The water will flow.
• The water flow will stop automatically
– once the preset flow time expires
or
– after approaching the sensor once again
or
– after leaving the sensor range.
Temperature selection

8
ZMI_001_2000103793-AQCT0025_#SEN_#AQU_#V1.fm
12. Adjusting the flow time
You can adjust the flow time from 10 seconds to 5 minutes seconds using the
remote control (not part of the scope of delivery; see Accessories, chapter 20).
13. Adjusting the range
You can adjust the range for body reflection using the remote control (not part of the
scope of delivery; see Accessories, chapter 20).
14. Hygiene flush
☞At the factory, the hygiene flush function is set so that water flows for 10 seconds 24
hours after the flush was last activated.
You can adjust the hygiene flush parameters using the remote control (not part of the
scope of delivery; see Accessories, chapter 20).
You can choose an interval of 0, 8, 24, 48, or 72 hours for the hygiene flush function
(0 = hygiene flush deactivated). You can adjust the flow time from 10 seconds to 10
minutes.
Display of hygiene flush on the fitting
14.1 Hold your hand around 10 cm from the sensor for 3 seconds.
14.2 Between the 1st and 2nd flashing of the LED, remove your hand from the sensor.
• Hygiene flush active: The LED flashes quickly 4 times.
• Hygiene flush inactive: The LED flashes slowly twice.
Activation/deactivation of hygiene flush on the fitting
14.3 Hold your hand around 10 cm from the sensor for 3 seconds.
14.4 Between the 6th and 8th flashing of the LED, remove your hand from the range of
the sensor.
• The LED does not flash.
14.5 After between 3 and 10 seconds, hold your hand around 10 cm from the sensor
again.
14.6 Once the LED has flashed three times, remove your hand from the range of the
sensor.
• The LED flashes quickly 4 times. The hygiene flush is active.
or
• The LED flashes slowly twice. The hygiene flush is deactivated.

9
ZMI_001_2000103793-AQCT0025_#SEN_#AQU_#V1.fm
15. Thermal disinfection
This fitting offers thermal disinfection to reduce the risk of a legionella infection.
Warning!
Personal protective measures (scald protection) must be implemented for the
duration of the thermal disinfection. This might include cordoning off the shower
facilities.
Failure to observe this instruction can result in injuries due to scalding.
The operator is responsible for the execution, monitoring, and logging (room,
tapping point, date, time, temperature and duration).
The manufacturer does not accept any liability for claims by third parties relating to
the improper execution of thermal disinfection on the part of the operator.
☞At the factory, the thermal disinfection function is set so that the fitting cools down for
1 minute after a 5 minute application time.
☞Thermal disinfection can only be triggered using the remote control.
You can adjust the thermal disinfection parameters using the remote control (not part
of the scope of delivery; see Accessories, chapter 20).
An application time of 3, 5, 10, 15, or 20 minutes can be chosen for the thermal
disinfection process. During the application time, water flows without interruption for
2 minutes; the water then flows in pulses until the end of the application time (water
and energy saving function). The cooling time can be set to 0, 1, 3, 5, or 10 minutes.
16. Adjusting the cleaning switch-off
You can activate the cleaning switch-off with the remote control (not part of the
scope of delivery, see Accessories, chapter 20) or directly on the fitting.
Cleaning switch-off on the fitting
16.1 Hold your hand around 10 cm from the sensor for 3 seconds.
16.2 Between the 3rd and 5th flashing of the LED, remove your hand from the range of
the sensor.
• The LED does not flash.
16.3 After between 3 and 10 seconds, hold your hand around 10 cm from the sensor
again.
16.4 Once the LED has flashed three times, remove your hand from the range of the
sensor.
• The fitting will be switched off for 3 minutes.
• The LED flashes in a 10 second cycle.
☞If you hold your hand around 10 cm from the sensor for at least 3 seconds, the fitting
will be reactivated before the 3 minutes has expired.

10
ZMI_001_2000103793-AQCT0025_#SEN_#AQU_#V1.fm
17. Maintenance and care
The fitting must be checked and maintained at regular intervals depending on the
water quality and in accordance with the local conditions, and rules and regulations
applicable at the site.
Maintain the following components:
• Shower head (see instructions for shower head)
• Filters (see chapter 18.)
Use suitable cleaning agents which are not harmful to the fitting in a proper manner
and rinse with water after use. High-pressure cleaners must not be used for
cleaning.
Remove the cover plate
For some maintenance tasks, the cover plate must be removed.
17.1 Remove the screws from the bottom of the cover plate (a).
17.2 Pull the bottom of the cover plate (b) forwards and detach at the top.
17.3 Close the water volume regulator (see step 10.2).
17.4 Disconnect the fitting.
18. Replacing the filters
Water volume regulator filters
18.1 Remove the cover plate (see chapter 17.).
18.2 Unscrew the locking screws (a) on the water volume regulators.
18.3 Replace the filters (b).
☞Important!
Note the installation position of the filters.
18.4 Reassemble in reverse order.