Franke Atlas Neo Little Butler ATL-FW-304 User manual

Atlas Neo Little Butler
EN Installation manual Kitchen Faucet
ES Manual de instalación Grifo de cocina
FR Manuel d‘installation Robinet de cuisine
ATL-FW-304 ATL-HO-304 ATL-HC-304

3
EN
Table of contents
Overview 4
Contents in box 4
Technical data 5
Installation instructions 5
Before you begin 5
Hot water installation options 5
Cold water installation options 5
Preliminary steps 6
Installation steps ATL-FW-304 7
Installation steps ATL-HO-304/ATL-HC-304 8
Usage and maintenance 9
Usage 9
General maintenance 9
Replacing the cartridge 10
Spare/replacement list ATL-FW-304 11
Spare/replacement list ATL-HO-304 12
Spare/replacement list ATL-HC-304 13

4
EN
Overview
Contents in box
ATL-HO-304 ATL-HC-304 ATL-FW-304
Note: Contact us immediately if you see inconsistencies.
phone: [phone]
website: www.franke.us/ks
email: [e-mail]
1. Faucet Assembly
2. Escutcheon
3. Escutcheon Rubber
Washer
4. Rubber Washer
5. Plastic Flange
6. Fixing Plate
7. Fixing Nut
8. 1/4“ Push Fitting
9. 1/4“ Poly-tube
10. 3/8“ Push Fitting
11. 3/8“ Poly-tube
12. Silicone Tube
13. Plastic Clamps
1. Faucet Assembly
2. Escutcheon
3. Escutcheon Rubber
Washer
4. Rubber Washer
5. Press Plate
6. Fixing Nut
7. 3/8“ Push Fitting
8. 3/8“ Poly-tube
38
3
11 12
13
13
9
8 10
7
4
4
5
6
5
7
6
11
22

5
EN
Technical data
Operating data Value
Water Pressure (recommended) 35-75 PSI 2.4-5 bar 240-500 kPa
Water Pressure (max.) 145 PSI 10 bar 1000 kPa
Hot Water Temperature (recommended) 120-140°F 50-60°C
Hole Size For Faucet 1-1/4“ 32 mm
Installation instructions
Before you begin
For best results, Franke recommends
this faucet be installed by a licensed,
professional plumber. The installer
should familiarize themselves with how
this dispensing faucet will be installed
and function as part of a point-of-use
water dispensing arrangement before
the products are installed because there
are several installation options. Make
certain to observe all local plumbing and
building codes during the installation.
Hot water installation
options
The ATL-HO-304 Series dispenser
oers hot water only. This dispenser
is required to be used in conjunction
with a Franke heating tank unit. Use of
a Franke ltration system in addition to
the heating tank is optional, but strongly
recommended in order to prolong the life
and improve the performance of the heat
tank, as well as providing much higher
quality water as compared to un-ltered
water entering the tank.
The ATL-HC-304 Series dispenser oers
hot and ltered water separately. This
dispenser must be used in conjunction
with both a Franke heating unit and a
Franke ltration system.
These models both utilize 3 tubes to
connect to the system.
– A 3/8“ poly-tube for the cold water
supply into the dispending faucet.
– A 1/4“ poly-tube to carry the ltered
water from the dispensing faucet to
the heating tank unit.
– An opaque high temperature silicone
tube to carry the heated water
from the heating tank back to the
dispensing faucet.
Cold water installation
options
The ATL-FW-304 Series dispenser
provides ltered drinking water as well
as the option of chilled drinking water.
This dispenser is required to be used
in conjunction with a Franke ltration
system. For chilled drinking water, a
Franke chiller tank unit is required. This
model utilizes a 3/8“ poly-tube to supply
ltered water to the faucets.
Certies this faucet complies with ASME A112.18.1 / CSA B125.1, NSF/ANSI/CAN 61-2020
(AB100 compliant, Q<1 ), NSF 372 & NSF 58. The faucet also complies with water usage
requirements of the California Energy Commission and the US Department of Energy.

6
EN
Important: Franke strongly recommends
using only genuine Franke components
in tandem with all Franke dispensing
faucets. The function of the dispensing
faucets cannot be guaranteed if using
ltration products, heating tanks, or
accessories other than genuine Franke
components.
Preliminary steps
1. It is recommended to take the
components and locate their
optimum positions before starting the
installation.
2. Make sure there is adequate clearance
for the dispenser handle(s) to open fully
without interference.
3. Make sure all plumbing and electrical
connections will reach the intended
mounting positions for all the
components and there will be no
obstruction or sharp bends in the
plumbing.
4. Make sure the counter top is no thicker
than 2“.
Important: For subsequent steps, it will
be required to cut and route tubing to t
the specic application in your home. All
tubing must be cut squarely and free of
burrs. Ensure there is no damage within 1“
of the cut end.
Do not use any form of sealing
compounds. This is not required for
push t connections, and using sealing
compounds could cause leaks.
All tubing connections must be routed to
avoid sharp bends and have enough slack
to avoid straining connections. Pull gently
on each connection to make sure they
are secure. See diagram below for details
on tubing installation and removal.
5. How to insert/remove tubing in push t
connections:
– Insert the Tube (1) squarely (g. 1A).
– Make sure to insert tubing completely
(g. 1B).
– To remove, push in Collet (2) and pull
out Tubing (1) (g. 1C).
6. Remove all contents from the package
and check for completeness.
7. Cut mounting hole 1-1/4“ in diameter
(32 mm) in the desired position (if one
isn‘t available).
8. Turn o water supply.
21
5
Tube Collet Body
5
Tube Collet Body
1A 1B
5
Tube Collet Body
1C
4
4
4
Heating Tank Filtration Systems Chiller Tank

7
EN
Installation steps
ATL-FW-304
1. Remove mounting hardware from
faucet body shank.
2. Slide the Escutcheon (1) over the shank.
Make sure the Rubber Washer (2) is
positioned in its seat in the Escutcheon
(g. 2A).
3. Place the faucet in the hole, orienting
the spout towards the sink bowl
with the handles in position to rotate
forward.
4. Install mounting hardware underneath
the mounting surface in the following
order: Rubber Washer (3), Press Plate (4)
and Fixing Nut (5) (g. 2B).
5. Connect the cold water supply to the
faucet:
– Screw in 3/8“ Push Fitting (6) into
Mounting Shank (7) (g. 2C).
Hand tighten only!
2C
6
7
Warning: Use of tools to tighten this
tting can lead to leaks!
– Insert the 3/8“ Poly-tube into the Push
Fitting (g. 1A, 1B).
Note: There should be a service label
attached to the poly-tubing. Do not
remove label.
6. Connect the 3/8“ poly-tube to the
outlet of the ltration system as
outlined in the ltration system
instructions.
7. Turn on the water and check for leaks.
2A
2
1
2B
4
5
3

8
EN
Installation steps
ATL-HO-304/ATL-HC-304
1. Remove mounting hardware from
faucet body shank.
2. Slide the Escutcheon (1) over the shank.
Make sure the Rubber Washer (2) is
positioned in its seat in the Escutcheon
(g. 3A).
3A
2
1
3. Place the faucet in the hole, orienting
the spout towards the sink bowl
with the handles in position to rotate
forward.
4. Install mounting hardware to the
mounting shank underneath the
mounting surface in the following
order: Rubber Washer (3), Plastic Flange
(4), Fixing Plate (5) and Fixing Nut (6)
(g. 3B).
7 Nm
3B
5. Tighten 2 screws in Fixing Nut (6) to
secure the nut (g. 3B).
6. Screw in the 1/4“ Push Fitting (8) into
the Hot Water Inlet (7) and screw the
3/8“ Push Fitting (9) into the Cold Water
Inlet (10) (g. 3C). Hand tighten only!
Warning: Use of tools to tighten this
tting can lead to leaks!
7. For the cold side, connect the 3/8“
poly-tube to the 3/8“ push tting
(g. 1A, 1B) and connect the other end
of the tube to the ltration system
as outlined in the ltration system
instructions.
Note: There should be a service label
attached to the water supply pipes from
the faucet. Do not remove label.
8. For the hot side, connect the 1/4“
poly-tube to the 1/4“ push tting
(g. 1A, 1B) and connect the other end
of the poly-tube to the heating tank
inlet as outlined in the heating tank
instructions.
3C
9
10
8
7
3
4
5
6

9
EN
Usage and maintenance
Usage
Pull the handle(s) forward to turn on the
water supply. Both valves will stay in the
“ON“position until rotated back to upright
position.
Note: The spout has a 360° swivel
capability.
Warning: Do not operate both handles
at the same time, as this can build up
pressure in the heating tank causing the
bladder to expand and eventually burst.
Such damage is not covered by the
warranty.
Seasonal Shutdown: If you plan to be
away from home for extended periods
of time, refer to the ltration system
and/or heating tank system instructions
(if applicable) under the Winterizing or
Seasonal Shutdown sections to prevent
system failures.
General maintenance
Do not use harsh detergents, solvents,
chemical agents, especially CHLORINE
based cleaners, metallic sponges, etc.
that could harm the surface and damage
the nish.
Clean only with soft sponge and soapy
water.
9. Connect the high temp Silicone Tube
(12) to the Mounting Nipple (11) and
secure the tubing using the Hose Clips
(13) (g. 3D).
3D
12
11
13
10. Connect the other end of the high
temp silicone tube to the heating tank
outlet as outlined in the heating tank
instructions.
Note: All tubing provided with the faucet
is intended to be longer than will be
necessary to make the connections to
the heating tank. It is recommended to
cut these tubes to the proper length to
remove any unnecessary loops or low
spots in tubing after installed.
11. Turn on the water and check for leaks.

10
EN
A
B
C
D
2.5 mm
Replacing the cartridge
1. Shut o the water supply to the faucet.
2. Turn on the faucet briey to relieve any
pressure inside the faucet.
3. Move the faucet handle to the “OFF”
position.
4. Remove the set screw from the Handle
Assembly (A) using a 2.5 mm Hex Key.
5. Pull the Lever Handle (A) from faucet
body.
6. Unscrew the Connector Kit (B) from the
cartridge.
7. Uscrew the Cartridge Lock Nut (C).
8. Lift Ceramic Disc Cartridge (D) from the
body and replace it with a new one.
9. Re-assemble faucet in reverse order.
10. Test for leakage.
17 mm