Franke Smart SMA-PO-CHR User manual

Smart
EN Installation manual Kitchen Faucet
ES Manual de instalación Grifo de cocina
FR Manuel d‘installation Robinet de cuisine
SMA-PO-CHR SMA-PO-SNI
PULL OUT

3
EN
Table of contents
Overview 4
Contents in box 4
Technical data 5
Installation instructions 5
Cleaning and maintenance 7
Replacing the cartridge 7
General maintenance 7
Spare/replacement list 8

4
EN
Overview
Contents in box
1. Pull Out Spray Assembly
2. Rubber Washer
3. Pull Out Hose
4. Faucet Assembly
5. Base Washer
6. Plastic Flange
7. Rubber Washer
8. Fixing Plate
9. Fixing Nut
10. Pull Out Supply Hose
11. Weight
12. Screws
13. Supply Hoses
Note: Contact us immediatly if you see inconsistencies.
phone: [phone]
website: www.franke.us/ks
email: [e-mail]
6
1
4
10 7
8
9
11
12
3 2
5
13

5
EN
Technical data
Operating data Value
Operating pressure (ideal) 30-75 PSI 2-5 bar 200-500 kPa
Operating pressure (max.) 100 PSI 7 bar 700 kPa
Operating pressure (min.) 35 PSI 2 bar 200 kPa
Water temperature (ideal) 100°F 38°C
Water temperature (max.) 158°F 70°C
Hole Size For Faucet 1 3/8“ 35 mm
Installation instructions
1. Remove all contents from the package
and check for completeness.
2. Connect the Pull Out Spray to the Pull
Out Hose Assembly hand tight. Ensure
the Rubber Washer is in place.
3. Turn o water supply.
4. Cut a mounting hole 13/8“ diameter
(35mm) in the desired position in
counter top or sink (if one isn’t
available).
5. Place the Base Washer (1) over the base
of the faucet.
Attention: The Base Washer (1) should be
sitting between the countertop and faucet.
Do not use putty or other sealant at this
location.
Notes: Solid surface installation: The
countertop mounting surface needs to be
at and free of debris, otherwise the faucet
may not sit properly. For tile installations
avoid installing faucet near or on top of
grout lines. This may cause a weak joint
between the faucet and the counter and
could cause leaks.
6. Install the mounting hardware to the
base of faucet body in the following
order - Plastic Flange (2), Rubber
Washer (3), Fixing Plate (4) as shown.
7. Tighten with the Fixing Nut (5) on the
base of faucet body.
2A
1
Certies this faucet complies with ASME A112.18.1 / CSA B125.1, NSF/ANSI/CAN 61-2020
(AB100 compliant, Q<1 ) & NSF 372. The faucet also complies with water usage requirements
of the California Energy Comission and the US Department of Energy.

6
EN
2B
8. Connect the Pull Out Hose (6) to the
Pull Out Supply Hose (7), with the quick
connection system.
2C
6
7
9. Align the tabs on the Pull Out Hose
tting with the slots in the Pull Out
Supply Hose sleeve and press the Pull
Out Hose tting into the Pull Out Supply
Hose sleeve until it clicks into place.
10. If you need to disconnect the hose,
press the tabs on the Pull Out Hose
tting and pull it out of the sleeve to
separate the tting from the sleeve.
11. Place the Weight (8) on the Pull
Out Hose(6) with the Screws (9)
approximately 2” (50 mm) above the
bend in the bottom of the Pull Out Hose.
2D
9
8
6
2” (50 mm)
12. Connect the exible Supply Hoses(10)
to the water supply in the house
(g.2E).
2E
10
10
13. Remove the Aerator using 11/16”
(17mm) wrench (g.2F), turn on water,
ush the faucet for any debris (g.2G)
and check for leaks. Reinstall the
Aerator (g.2H) and ensure everything
is functioning properly.
2G2F 2H
2
4
5
3

7
EN
Cleaning and maintenance
Replacing the cartridge
1. Shut o the water supply to the faucet.
2. Turn on the faucet briey to relieve any
pressure inside the faucet.
3. Move the faucet handle to the “OFF”
position.
4. Remove the Plastic Cover (C) from
Handle (A).
5. Remove the Screw (B) using an allen
key.
6. Pull the Lever Base (A) from the faucet
body.
7. Unscrew the Cap (D).
8. Unscrew the Cartridge Lock Nut (E).
9. Lift Ceramic Disc Cartridge (F) from
the body and replace it with new
cartridge. Ensure the two lugs on
bottom of the cartridge sit properly in
the allocated holes at the base of the
body.
10. Re-assemble faucet in reverse order.
11. Test for leakage.
General maintenance
Clean aerator periodically for any buildup.
Do not use harsh detergents, solvents,
chemical agents, metallic sponges, etc.
that could harm the surface and damage
the nish. Clean only with a soft sponge
and soapy water.
Do not store chemicals or cleaning agents
in the immediate vicinity of the faucet and
connection hoses. Chemical vapors could
cause damage.
A
DBC
E
F
2.5 mm
30mm
106 in-lbs

8
EN
*Must specify nish
“CH“ chrom; “SN“ satin nickel
Spare/replacement list
7
8
1
4
5
6
3
10
9
17
16
11
18
15
14
12
13
2
1, 2, 3 F20059* Handle Assembly
4F20002* Cap
5F20003 Lock Nut
6F20004 Cartridge
7F20034 Rubber Washer
8F20006 Check Valve 1.75 Gpm
9F20051 Aerator
10 F20058* Pull-Out Spray
Assembly
11 F20009 Base Washer
12 F20010 Mounting Hardware Kit
13 F20057 Weight
14 F20053 Pull-Out Hose
15 F20054 Check Valve
16 F20055 Pull-Out Supply Hose
17 F20056 Supply Hoses
18 F20017 Plastic Flange

9
EN
For any further information about our products, about the installation of them or about the
warranty please contact our customer service department:
Franke Home Solutions
North America, LLC
800 Aviation Parkway
Smyrna, TN 37167, USA
Phone: [phone]
[e-mail]
Franke Kindred Canada Ltd.
1000 Franke Kindred Way
Midland, ON LR4 4K9
Phone: [phone]
[e-mail]
Warranty website: https://www.franke.com/us/en/hs/support/warranty.html