Franke FCTSH90XB1 Parts list manual

INSTRUCTIONS & INSTALLATION MANUAL
FCTSH90XB1
90CM T-SHAPE RANGEHOOD

USER MANUAL ..................................................................................................... 3
INSTALLATION GUIDE ......................................................................................... 7

1. SAFETY INFORMATION
For your safety and correct operation of
the appliance, read this manual carefully
before installation and use. Always keep
these instructions with the appliance
even if you move or sell it. Users must
fully know the operation and safety
features of the appliance.
The wire connection has to be done
by qualified technician.
• The manufacturer will not be held liable
for any damages resulting from
incorrect or improper installation.
• The minimum safety distance between
the cooker top and the extractor hood is
650 mm (some models can be installed
at a lower height, please refer to the
paragraphs on working dimensions and
installation).
• If the instructions for installation for the
gas hob specify a greater distance, this
must be respected.
• Check that the mains voltage
corresponds to that indicated on the
rating plate fixed to the inside of the
hood.
• Means for disconnection must be
incorporated in the fixed wiring in
accordance with the wiring rules.
• For Class I appliances, check that the
domestic power supply guarantees
adequate earthing.
• Connect the extractor to the exhaust
flue through a pipe of minimum
diameter 120 mm. The route of the flue
must be as short as possible.
• Regulations concerning the discharge of air
have to be fulfilled.
• Do not connect the extractor hood to
exhaust ducts carrying combustion
fumes (boilers, fire- places, etc.).
• If the extractor is used in conjunction
with non-electrical appliances (e.g.
gas burning appliances), a sufficient
degree of aeration must be guaranteed
in the room in order to prevent the
backflow of exhaust gas. When the
cooker hood is used in conjunction with
appliances supplied with energy other
than electric, the negative pressure in the
room must not exceed 0,04 mbar to
prevent fumes being drawn back into
the room by the cooker hood.
• The air must not be discharged into a
flue that is used for exhausting fumes
from appliances burning gas or other
fuels.
• If the supply cord is damaged, it must be
replaced by the manufacturer or by its
approved service agent.
• Connect the plug to a socket complying
with current regulations, located in an
accessible place.
• With regards to the technical and safety
measures to be adopted for fume
discharging
3

it is important to closely follow the
regulations provided by the local
authorities.
WARNING: Before installing the
Hood, remove the protective films.
• Use only screws and small parts in
support of the hood.
WARNING: Failure to install the
screws or fixing device in
accordance with these instructions
may result in electrical hazards.
• Do not look directly at the light through
optical devices (binoculars, magnifying
glasses).
• Do not flambè under the range hood;
risk of fire.
• This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities or lack of experience and
knowledge, unless they have been
given supervision or instruction
concerning use of the appliance by a
person responsible for their saftey.
• Children should be supervised to
ensure that they do not play with the
appliance.
Accessible parts may be- come
hot when used with cooking
appliances.
• Clean and/or replace the Filters after the
specified time period (Fire hazard). See
paragraph Care and Cleaning.
• There is a fire risk if cleaning is not
carried out in accordance with the
instructions.
• There shall be adequate ventilation of
the room when the range hood is used
at the same time as appliances burning
gas or other fuels (not applicable to
appliances that only discharge the air
back into the room).
• The symbol on the product or on its
packaging indicates that this product
may not be treated as household waste.
Instead it shall be handed over to the
applicable collection point for the
recycling of electrical and electronic
equipment. By ensurin g this product is
disposed of correctly, you will help
prevent potential negative consequences
for the environment and human health,
which could otherwise be caused by
inappropriate waste handling of this
product. For more detailed information
about recycling of this product, please
contact your local city office, your
household waste disposal service or the
shop where you purchased the product.
4

2. USE
• The extractor hood has been designed
exclusively for domestic use to eliminate
kitchen smells.
• Never use the hood for purposes other
than for which it has been designed.
• Never leave high naked flames under
the hood when it is in operation.
• Adjust the flame intensity to direct it onto
the bottom of the pan only, making sure
that it does not engulf the sides.
• Deep fat fryers must be continuously
monitored during use: overheated oil
can burst into flames.
3. CARE AND CLEANING
- The Activated charcoal filter is not
washable and cannot be regenerated,
and must be replaced approximately
every 4 months of operation, or more
frequently for particularly heavy usage
(W).
The Grease filters must be cleaned every
1 months of operation, or more frequently
for particularly heavy usage, and can be
washed in a dishwasher (Z).
• Clean the hood using a damp cloth and
a neutral liquid detergent.
5
Z
W

4. CONTROLS
Button
Function
Led
T1
By pressing T1 Button the controls board
are On and Off.
After 2 minuts without button pressing,
the control board turn Off.
Show 0
T2
Decreases the speed of the Motor.
Show the selected speed
T3
Increases the speed of the Motor.
Show the selected speed
T4
1) Press briefly:
Activates/Deactivates the Delay
2) Press and hold for at least 3 seconds:
Activates the Delay settings
Enable shutdown with same minutes
delay (Motor+Lights). It is possible to
change the operating speed when this
function is enabled.
It’s possible to choose the timing of Delay:
Press for 3 seconds the button until the
Digit flash. Within 10 seconds set from 1
to 9 the minutes of Delay by pressing T2
or T3 button. Press again the Button T4
to confirm.
Flash
L
Turns the Lighting System on and off.
On / Off
5. LIGHTING
• For replacement contact technical
support (“To purchase contact technical
support”).
6

INSTALLATION MANUAL
Warning!
Before proceeding with installation, please read the
recommendations and suggestions in the user manual.

8
I = 9x L = 9x P1 = 2x
N1
N2
O
V

9
ø 120 mm
ø 150 mm
2x
2x ø 150 mm
112.0569.559
112.0571.150
P2 = 2x
P3 = 2x
Q
R
650
mm.
650
mm.

10
- CJ
CJ
1