Franke FKU908TCWXS User manual

1
HANDBOOK HOOD FKU908TCWXS 9925031-110.0019.380
UPDATED JANUARY 2010
MOTOR NR 01 POWER IMPUT : 340 W
SPEED : 8+INTENSIVE
LIGHTING : 16 W 1 NEON
TOTAL POWER : 356 W
FLOW RATE (FREE DELIVERY) : 810 M3/H
FLOW RATE (IEC 61591) 760/670 M3/H
SOUND POWER (IEC 60704-2-13) 69
IMPUT VOLTAGE : 230V 50 HZ
EXIT DIAMETER 150 MM
PRESSURE MAX 500 PA
CONTROLS : ELECTRONIC – LOW TENSION PUSH BUTTON KEY TOUCH
CONTROL
CONTENTS:
TECHNICAL
DRAWING
ELECTRICAL CONNECTION
CLEANING THE COMFORT PANELS
CONTROLS HOW IT WORKS
METAL GREASE FILTERS
CHARCOAL FILTER
SUBSTITUTION OF THE CHARCOAL FILTER
CHANGING LAMP 16 W NEON LAMP
LIST SPARE PARTS
EXPLODED VIEW
WIRING DIAGRAM

2
TECHNICAL DATA

3

4
ELECTRICAL CONNECTION •
Connect the hood to the mains through a two-pole switch having a contact gap of at least 3
mm.
• Remove the grease filters (see paragraph Maintenance) being sure that the connector of the
feeding cable is correctly inserted in the socket placed on the side
of the fan.
CLEANING THE COMFORT PANELS
• Pull the Comfort Panel to open it.
• Disconnect the panel from the hood canopy by sliding the fixing pin
lever.
• The comfort panel must never be washed in a dishwasher.
• Clean the outside using a damp cloth and neutral liquid detergent.
• Clean the inside as well using a damp cloth and neutral detergent;do
not use wet cloths or sponges, or jets of water; do not use abrasive
substances.
• When the above operation has been completed, hook the panel back
to the hood canopy and close it by turning the knob in the opposite
direction.

5

6
KEY- FUNCTION DISPLAY
A Switches the extractor motor on and off at
the latest selected speed
Indicates the selected speed.
B Decreases the suction speed. The number of lit LEDS decreases.
C Increases the suction speed. The number of lit LEDS increases.
D By pressing this key it is possible to start
the intensive
speed from any previously selected speed
except the Delay-function and 24H-function.
This speed has been timed at 10 minutes.
After that time the system activates
automatically the latest selected speed. This
function is suitable for cooking conditions
when vapours and smells are at the utmost
emission.
I flashes and the LEDS are all lit.
By pressing the key the function is
stopped.
E By pressing this key it is possible to set up
the motor to a suction speed at 100 m3/h .
24 appears and the LEDS extinguish one
by one. By pressing the key the function is
stopped

7
F By pressing this key it is possible to set the
delayed shutdown of the motor and the
lighting to 30 minutes.
This function is suitable for a complete
elimination of residual cooking odours.
Functioning only when the motor is on(not
during the 24H-function or intensive function).
By pressing the key the function is stopped
A flashing clock-symbol appears.
By pressing the key the function is
stopped
G By pressing this key for about 2 seconds it
is possible to reset the filter saturation alarm
After 100 working hours a drop-symbol
appears. Metal grease filters have to be
washed.
H By pressing this key the intensity of the
lighting system can be decreased.
Keyboard lock: it is possible to jam the keyboard when, for example, cleaning the glass.The motor and lights are switched
Off.By pressing the F-key (Delay) for about 5 seconds the keyboard block can be activated or deactivated.
This function is confirmed by a Beep and by moving motor LEDS on display.

8
Metal grease filters
Metal filters can be washed also in a dish machine. They need to be washed every
time a drop-symbol appears in the display or at least every two months. In case of
very frequent use these have to be washed even more often. Alarm reset • Press
the G-key for at least 2 seconds.
Cleaning
• Open the comfort panel.
• Remove the filters one by one by pushing them backwards and pulling them
down contemporaneously.
• Wash the filters. Pay attention not to bend them. Make sure that filters are
completely dry before putting them into their seat. (a possible modification of the
filter surface doesn’t influence its efficiency).
• Place the filters again into their seats and make sure that the handle of the filter
remains outside.
• Close the comfort panel.
Charcoal filter (recycling version)
This filter cannot be washed or regenerated. It must be replaced when the C
appears on the display or at least once every 4 months.
The filter saturation alarm has to be activated already before. Activation of the
alarm signal • In the recycling version hoods the filter saturation alarm must be
activated during the installation or later.
• Switch off the hood and the lights.
• Press the E-key for about 5 seconds until the last two segments of the motor
LEDS are lit on the display.
• By releasing the E-key the clock icon starts to flash.
• Within 3 seconds press the D-key to activate/deactivate charcoal filter
saturation alarm.
• C-symbol lit - charcoal filter saturation alarm ACTIVATED. • C-symbol unlit -
charcoal filter saturation alarm DEACTIVATED.

9
SUBSTITUTION OF THE CHARCOAL FILTER
Alarm reset
• Switch off the motor and the lighting system.
• Press the G-key for at least 2 seconds. Substitution of the filter
• Open the confort panel.
• Remove the metal grease filters.
• Remove the charcoal filter as indicated in the picture.
• Place the filter again into its seat.
• Place again the metal grease filters into their place.
CHANGING LAMP 16 W Neon Lamp
• Open the comfort panel.
• Remove the neon lamp guard by unfastening the screws and sliding it out of its
housing.
• Change the Neon lamp or the Starter, taking care to ensure that the new
components have the same characteristics as the old ones.
• Replace the neon lamp guard.
• Close the comfort panel.

Position Spare part code franke fun number description quantity PRODUCT
1 1961081 133.0036.292 CASING+BRACKET 1 9925031
2 1961446 133.0061.944 KIT BOARD TERMIN. BLOCK+COVER 1 9925031
4 1961084 133.0036.931 POWER PACK 230V 50 HZ 1 9925031
5 9925204 112.0016.756 CHARCOAL FILTER/ PANEL 1 9925031
8 1960309 133.0036.314 CLIP 2 9925031
9 1961085 133.0058.404 SELF-SUPPORTING FILTER 3 9925031
10 1961385 133.0017.004 PIVOT STOPPER NR 02 PIECES 1 9925031
11 1961086 133.0036.539 SUPPORT SPOT-LIGHT 1 9925031
12 1961447 133.0059.032 STARTER FS 11 220240V 1 9925031
13 1961088 133.0018.578 LAMP HOLDER 1 9925031
14 1961089 133.0036.550 LAMP 16W/25 L 720 MM 1 9925031
15 1961090 133.0036.551 LAMP HOLDER 1 9925031
17 1961092 133.0032.532 PANNEL 1 9925031
18 1961392 133.0057.285 SUPPORT HINGE FOR LIGHTSPOT 1 9925031
102 1961272 133.0056.065 CONTROLS ASSEMBLY 1 9925031
104 1960684 133.0059.766 10 WAY FLAT CABLE 150 1 9925031
302 1961418 133.0059.007 FAN MOTOR 1 9925031
305 1961319 133.0051.604 KIT MOTOR SHOCK ABSORBER 4 9925031
312 1960631 133.0016.892 CAPACITOR 1 9925031
330 1961274 133.0051.414 SET CONNECTION FOR MOTOR 1 9925031
399 1961416 133.0059.008 KIT MOTOR ASSEMBLY 1000MC 220-50/60 1 9925031
501 1961275 133.0046.952 SET 2 FIXING BRACKETS 1 9925031
506 1961276 133.0046.956 SET FLANGE- CONNECTION 1 9925031
508 1960200 133.0016.959 SPIGOT 120-150 1 9925031
509 1961093 133.0036.636 LOWER DUCT MM 545 1 9925031
511 1961094 133.0036.639 UPPER DUCT 470 MM 1 9925031
606 1961277 133.0052.537 SET FIXING BRACKETS 1 9925031
610 1961278 133.0051.413 SET CONNECTION FIXING 1 9925031
product co