Free2Move eSolutions ePublic User manual
USER MANUAL, USE AND
MAINTENANCE MANUAL
USER MANUAL, USE AND
MAINTENANCE MANUAL
I
USER MANUAL, USE AND
MAINTENANCE MANUAL GB
GB
GB
SAFETY INSTRUCTIONS
PURPOSE AND STRUCTURE OF THE DOCUMENT
LIST OF DOCUMENTS IN THE APPENDIX
WARRANTY AND DELIVERY CONDITIONS
Keep this document in a safe place for easy access at all times during installation
and maintenance.
Operators are required to read this manual and to comply strictly with the
instructions it contains. Free2Move eSolutions S.p.A. cannot be held liable for
damage caused to persons and/or property, or to the equipment, if the conditions
described below have not been complied with. The purpose of this document is
to support qualied technicians, who have received appropriate training and/or
have demonstrated adequate skills and knowledge in the construction, installation,
operation and maintenance of electrical equipment.
The warranty requirements are contained in the Terms and Conditions of Sale
section included with the purchase order for this product.
NOTE: Any modication not approved by Free2Move eSolutions S.p.A. will
immediately invalidate the product warranty.
The warranty conditions are considered valid if the customer complies with the
information contained in this manual; any deviation from the warranty conditions
with respect to what is described below must be expressly indicated in the
purchase order.
Free2Move eSolutions S.p.A.
declares that the equipment
complies with the legal provisions currently in force in the country of installation
and has issued the relative declaration of conformity.
Free2Move eSolutions S.p.A.
assumes no responsibility for failure to comply with
the instructions for proper installation and cannot be held responsible for the
systems upstream or downstream of the equipment supplied.
It is absolutely forbidden to modify the equipment.
Any modication, manipulation or alteration of the hardware or software not expressly
agreed with
Free2Move eSolutions S.p.A.
will immediately void the warranty.
Due to the large number of possible combinations of system congurations and
installation environments, it is essential to check the following before installing the
product: adequate space for housing the equipment, ambient noise produced by
the environment and possible ammable conditions
.
Free2Move eSolutions S.p.A.
cannot be held responsible for defects or malfunctions deriving from: improper
use of the equipment; deterioration due to transport or particular environmental
conditions; incorrect or insucient maintenance; tampering or unsafe repairs; use
or installation by unqualied persons. Free2Move eSolutions S.p.A. is not
responsible for any disposal of the equipment, or part thereof, that does not
comply with the regulations and laws in force in the country of installation.
If the equipment is used in a manner not specied in this manual, the protection
provided by the equipment may be impaired.
This document was originally written in Italian. Therefore, in case of inconsistencies
or doubts, ask Free2Move eSolutions S.p.A. for the original document.
In addition to this user manual, product documentation can be viewed and
downloaded by visiting
Free2Move eSolutions S.p.A.
website
(https://www.e solutions.free2move.com/ low-power-charging-solutions/).
This document only contains the information deemed necessary for the use and
routine maintenance of the equipment. Installation requires qualied personnel for
the design and creation of a dedicated, state of the art electricity supply system and to
certify the system in compliance with local regulations and the energy supply conctract.
Installation must be carried out in accordance with the regulations in force in the
country of installation and in compliance with all safety regulations for carrying
out electrical work. It is forbidden to entrust the installation or maintenance of the
product to unqualied persons or those in an altered physical or mental state.
The customer bears civil liability for the qualication and mental or physical state of
the personnel who handle the equipment.
Such personnel must always use the personal protective equipment (PPE) required
by the laws of the country of destination and by the instructions of their employer.
This manual contains important safety instructions that must be followed
during installation and maintenance of the equipment.
This user and maintenance manual is a guide to help you to work safely
and carry out the necessary operations to keep your equipment in good
working order.
The installer must read this document in its entirety before installing the
equipment.
1
2
GB
GB
SAFETY INSTRUCTIONS
PURPOSE AND STRUCTURE OF THE DOCUMENT
LIST OF DOCUMENTS IN THE APPENDIX
WARRANTY AND DELIVERY CONDITIONS
Keep this document in a safe place for easy access at all times during installation
and maintenance.
Operators are required to read this manual and to comply strictly with the
instructions it contains. Free2Move eSolutions S.p.A. cannot be held liable for
damage caused to persons and/or property, or to the equipment, if the conditions
described below have not been complied with. The purpose of this document is
to support qualied technicians, who have received appropriate training and/or
have demonstrated adequate skills and knowledge in the construction, installation,
operation and maintenance of electrical equipment.
The warranty requirements are contained in the Terms and Conditions of Sale
section included with the purchase order for this product.
NOTE: Any modication not approved by Free2Move eSolutions S.p.A. will
immediately invalidate the product warranty.
The warranty conditions are considered valid if the customer complies with the
information contained in this manual; any deviation from the warranty conditions
with respect to what is described below must be expressly indicated in the
purchase order.
Free2Move eSolutions S.p.A.
declares that the equipment
complies with the legal provisions currently in force in the country of installation
and has issued the relative declaration of conformity.
Free2Move eSolutions S.p.A.
assumes no responsibility for failure to comply with
the instructions for proper installation and cannot be held responsible for the
systems upstream or downstream of the equipment supplied.
It is absolutely forbidden to modify the equipment.
Any modication, manipulation or alteration of the hardware or software not expressly
agreed with
Free2Move eSolutions S.p.A.
will immediately void the warranty.
Due to the large number of possible combinations of system congurations and
installation environments, it is essential to check the following before installing the
product: adequate space for housing the equipment, ambient noise produced by
the environment and possible ammable conditions
.
Free2Move eSolutions S.p.A.
cannot be held responsible for defects or malfunctions deriving from: improper
use of the equipment; deterioration due to transport or particular environmental
conditions; incorrect or insucient maintenance; tampering or unsafe repairs; use
or installation by unqualied persons. Free2Move eSolutions S.p.A. is not
responsible for any disposal of the equipment, or part thereof, that does not
comply with the regulations and laws in force in the country of installation.
If the equipment is used in a manner not specied in this manual, the protection
provided by the equipment may be impaired.
This document was originally written in Italian. Therefore, in case of inconsistencies
or doubts, ask Free2Move eSolutions S.p.A. for the original document.
In addition to this user manual, product documentation can be viewed and
downloaded by visiting
Free2Move eSolutions S.p.A.
website
(https://www.e solutions.free2move.com/ low-power-charging-solutions/).
This document only contains the information deemed necessary for the use and
routine maintenance of the equipment. Installation requires qualied personnel for
the design and creation of a dedicated, state of the art electricity supply system and to
certify the system in compliance with local regulations and the energy supply conctract.
Installation must be carried out in accordance with the regulations in force in the
country of installation and in compliance with all safety regulations for carrying
out electrical work. It is forbidden to entrust the installation or maintenance of the
product to unqualied persons or those in an altered physical or mental state.
The customer bears civil liability for the qualication and mental or physical state of
the personnel who handle the equipment.
Such personnel must always use the personal protective equipment (PPE) required
by the laws of the country of destination and by the instructions of their employer.
This manual contains important safety instructions that must be followed
during installation and maintenance of the equipment.
This user and maintenance manual is a guide to help you to work safely
and carry out the necessary operations to keep your equipment in good
working order.
The installer must read this document in its entirety before installing the
equipment.
1
2
TABLE OF CONTENTS
SECTION
SECTION
PAGE
PAGE
1.
6.
7.
8.
3.
4.
2.
5.
1.1.
3.1.
2.1.
5.1.
1.2.
3.2.
3.6.
2.2.
2.3.
5.2.
1.3.
3.3.
3.7.
1.4.
3.4.
3.8.
1.5.
3.5.
3.9.
3.10.
3.11.
GENERAL INFORMATION
TROUBLE SHOOTING
MAINTENANCE
DECOMMISSIONING AND DISPOSAL
INSTALLATION
FIRST START-UP AND CONFIGURATION
SAFETY AND EQUIPMENT
INSTRUCTIONS FOR USE
Field of use
Preparing for Installation
Safety warnings
Preliminary charging operations
Support
Tools required
Installation in fresh concrete
Proper use
Product handling
Charging operations
Techical data
Package Contents
Positioning on the anchor plate
Symbols and denitions
Space and positioning
Charging station installation
Product dimensions and features
Unpacking
Connection of power and earth cables
Communication cables connection
Closing operations and power supply
5
32
33
34
13
27
11
28
5
14
19
11
28
6
15
21
11
12
29
7
15
22
8
16
23
26
27
10
17
GB
GB
3
4
TABLE OF CONTENTS
SECTION
SECTION
PAGE
PAGE
1.
6.
7.
8.
3.
4.
2.
5.
1.1.
3.1.
2.1.
5.1.
1.2.
3.2.
3.6.
2.2.
2.3.
5.2.
1.3.
3.3.
3.7.
1.4.
3.4.
3.8.
1.5.
3.5.
3.9.
3.10.
3.11.
GENERAL INFORMATION
TROUBLE SHOOTING
MAINTENANCE
DECOMMISSIONING AND DISPOSAL
INSTALLATION
FIRST START-UP AND CONFIGURATION
SAFETY AND EQUIPMENT
INSTRUCTIONS FOR USE
Field of use
Preparing for Installation
Safety warnings
Preliminary charging operations
Support
Tools required
Installation in fresh concrete
Proper use
Product handling
Charging operations
Techical data
Package Contents
Positioning on the anchor plate
Symbols and denitions
Space and positioning
Charging station installation
Product dimensions and features
Unpacking
Connection of power and earth cables
Communication cables connection
Closing operations and power supply
5
32
33
34
13
27
11
28
5
14
19
11
28
6
15
21
11
12
29
7
15
22
8
16
23
26
27
10
17
GB
GB
3
4
1.
1.1.
1.2.
GENERAL INFORMATION
Field of use
Support
ePublic is the ideal Alternate Current charging solution for electric vehicles for
public and semi-public applications: it is available in single-phase congurations up
to 7.4 kW or three-phase up to 22 kW and equipped with a Type 2 socket
(according to the IEC 62196-2 standard). Other types of connectors are not
supported. Characterised by signicant robustness and ease of use, this device
allows two electric vehicles to be charged simultaneously up to a maximum of
44kW (22kW each) with a Type T2 socket.
Free2Move eSolutions S.p.A. is not liable for damage of any kind resulting from
incorrect or careless operations.
For any further information or requests for further support, Free2Move eSolutions
S.p.A. is available through the dedicated section of the website:
www.esolutions.free2move.com/low-power-charging-solutions/ePublic
This equipment is a charging station for electric vehicles; the following classication
(according to IEC 61851-1) identies its characteristics:
Power supply: permanently connected to the AC power supply grid
Output: alternate current
Environmental conditions: outdoor use
A device for free access places
Fixed installation on the ground
Protection against electric shock: Class I
Charging type: Mode 3 according to the IEC 61851-1 standard
Optional function for ventilation not supported
The entire power supply system must be prepared and sized in
compliance with the local and international standards in force according
to the product conguration and the power rating chosen.
This document describes how to install, congure, and maintain the
product. A description of the characteristics of the equipment is provided
to identify its major components and specify the technical terminology
used in this manual.
The equipment may not be used for any purpose other than that its
intended use. The equipment must not be used by inexperienced
personnel, or even by expert personnel if operations are carried out on
the equipment that do not comply with this manual and the
accompanying documentation.
In case of installation in TN-type earthing systems, there may be
additional specic local regulations regarding system safety and
protection against faults that the installer must understand and implement.
The device may only be connected to the mains in countries for which it has
been certied / approved.
This chapter contains information on models, details on equipment,
characteristics and technical data, overall dimensions and identication
of the equipment. In some cases (e.g. data sim, etc.), it may be necessary
to look up software conguration features separately by consulting
additional documentation to this manual, which is intended for
specialised technicians trained Free2Move eSolutions S.p.A.
GB
GB
5
6
1.
1.1.
1.2.
GENERAL INFORMATION
Field of use
Support
ePublic is the ideal Alternate Current charging solution for electric vehicles for
public and semi-public applications: it is available in single-phase congurations up
to 7.4 kW or three-phase up to 22 kW and equipped with a Type 2 socket
(according to the IEC 62196-2 standard). Other types of connectors are not
supported. Characterised by signicant robustness and ease of use, this device
allows two electric vehicles to be charged simultaneously up to a maximum of
44kW (22kW each) with a Type T2 socket.
Free2Move eSolutions S.p.A. is not liable for damage of any kind resulting from
incorrect or careless operations.
For any further information or requests for further support, Free2Move eSolutions
S.p.A. is available through the dedicated section of the website:
www.esolutions.free2move.com/low-power-charging-solutions/ePublic
This equipment is a charging station for electric vehicles; the following classication
(according to IEC 61851-1) identies its characteristics:
Power supply: permanently connected to the AC power supply grid
Output: alternate current
Environmental conditions: outdoor use
A device for free access places
Fixed installation on the ground
Protection against electric shock: Class I
Charging type: Mode 3 according to the IEC 61851-1 standard
Optional function for ventilation not supported
The entire power supply system must be prepared and sized in
compliance with the local and international standards in force according
to the product conguration and the power rating chosen.
This document describes how to install, congure, and maintain the
product. A description of the characteristics of the equipment is provided
to identify its major components and specify the technical terminology
used in this manual.
The equipment may not be used for any purpose other than that its
intended use. The equipment must not be used by inexperienced
personnel, or even by expert personnel if operations are carried out on
the equipment that do not comply with this manual and the
accompanying documentation.
In case of installation in TN-type earthing systems, there may be
additional specic local regulations regarding system safety and
protection against faults that the installer must understand and implement.
The device may only be connected to the mains in countries for which it has
been certied / approved.
This chapter contains information on models, details on equipment,
characteristics and technical data, overall dimensions and identication
of the equipment. In some cases (e.g. data sim, etc.), it may be necessary
to look up software conguration features separately by consulting
additional documentation to this manual, which is intended for
specialised technicians trained Free2Move eSolutions S.p.A.
GB
GB
5
6
GB
GB
7
8
Model: ePublic
Type of socket Type
Standard IEC61851-1
Charging mode Mode 3
Maximum power per socket 22kW
Power system 3P + N + PE
Rated voltage 400V AC ± 10%
Frequency 50-60Hz
Rated current 64A
Rated impulse withstand voltage (Uimp) ≥4kV
Rated conditional short-circuit current of an assembly (Icc) 10kA
Rated Diversity Factor (RDF) 1
Level of pollution 2
EMC classification Class B emissions
Protection measures against electrical shocks Class I
Power supply connection Permanently connected to the electricity grid
Type of grounding system TT or TN (both with PE)
Indoor / outdoor installation Outdoor
Fixed or removable installation Fixed
Overvoltage category III
IP protection class IP 54
IK protection Class IK10
Casing material FE360 with cataphoresis, painting and polycarbonate
Dimensions 1405mm x 422mm x 393mm
Weight 48kg
Operating temperature -25….+50°C
Storage temperature -25…+70°C
Humidity 0 ... 95% (without condensation)
Altitude Up to 2000m
Product intended for use Ordinary person
Location in area with Unrestricted access
Thermal-magnetic circuit breaker Included (2 x MCB 4P D40 10kA)
Residual-current device Included (2 x RCD 4P Type A 40A 30mA & RCM 6mA DC)
Energy meter MID certified
Contactor 2xNo/4xNO 40A, AC-1 @40°C
OCPP OCPP 1.6-J
Internal Load Manager Y
Connectivity Modbus TCP / IP
G0 3G / 4G Y
RFiD reader Y
Status LED Y
4.3" TFT monitor Y
Certification CE
1.3. Technical data
It is strictly prohibited to:
Install the equipment in environments subject to particular ammability
conditions or in adverse or unacceptable environmental conditions
Use the equipment with defective or disabled safety devices
Use the equipment or parts of the equipment by connecting it to other
machines or equipment, unless expressly provided for
Modify operating parameters that are not accessible to the operator and/or
parts of the equipment to alter its performance or make changes to its insulation
Clean the product with corrosive products that could damage parts of the
equipment or generate electrostatic charges
Use or install the equipment or any associated parts thereof without having read
and properly understood the contents of the operation and maintenance manual
1.4. Symbols and denitions
DANGER
WARNING
CAUTION
ATTENTION
QUALIFIED
PERSONNEL
This symbol indicates imminent danger that may
cause death or serious injuries.
This symbol indicates a dangerous situation that may
cause death or serious injuries.
This symbol indicates a dangerous situation that may
cause slight injuries.
This symbol indicates a situation that may cause
material damage to ePublic.
Work that must be carried out by a technician, from
this point ‘Qualied Personnel’, qualied to design,
create a state-of-the-art domestic electrical system
and certify it in compliance with local regulations and
the energy supply contract.
GB
GB
7
8
Model: ePublic
Type of socket Type
Standard IEC61851-1
Charging mode Mode 3
Maximum power per socket 22kW
Power system 3P + N + PE
Rated voltage 400V AC ± 10%
Frequency 50-60Hz
Rated current 64A
Rated impulse withstand voltage (Uimp) ≥4kV
Rated conditional short-circuit current of an assembly (Icc) 10kA
Rated Diversity Factor (RDF) 1
Level of pollution 2
EMC classification Class B emissions
Protection measures against electrical shocks Class I
Power supply connection Permanently connected to the electricity grid
Type of grounding system TT or TN (both with PE)
Indoor / outdoor installation Outdoor
Fixed or removable installation Fixed
Overvoltage category III
IP protection class IP 54
IK protection Class IK10
Casing material FE360 with cataphoresis, painting and polycarbonate
Dimensions 1405mm x 422mm x 393mm
Weight 48kg
Operating temperature -25….+50°C
Storage temperature -25…+70°C
Humidity 0 ... 95% (without condensation)
Altitude Up to 2000m
Product intended for use Ordinary person
Location in area with Unrestricted access
Thermal-magnetic circuit breaker Included (2 x MCB 4P D40 10kA)
Residual-current device Included (2 x RCD 4P Type A 40A 30mA & RCM 6mA DC)
Energy meter MID certified
Contactor 2xNo/4xNO 40A, AC-1 @40°C
OCPP OCPP 1.6-J
Internal Load Manager Y
Connectivity Modbus TCP / IP
G0 3G / 4G Y
RFiD reader Y
Status LED Y
4.3" TFT monitor Y
Certification CE
1.3. Technical data
It is strictly prohibited to:
Install the equipment in environments subject to particular ammability
conditions or in adverse or unacceptable environmental conditions
Use the equipment with defective or disabled safety devices
Use the equipment or parts of the equipment by connecting it to other
machines or equipment, unless expressly provided for
Modify operating parameters that are not accessible to the operator and/or
parts of the equipment to alter its performance or make changes to its insulation
Clean the product with corrosive products that could damage parts of the
equipment or generate electrostatic charges
Use or install the equipment or any associated parts thereof without having read
and properly understood the contents of the operation and maintenance manual
1.4. Symbols and denitions
DANGER
WARNING
CAUTION
ATTENTION
QUALIFIED
PERSONNEL
This symbol indicates imminent danger that may
cause death or serious injuries.
This symbol indicates a dangerous situation that may
cause death or serious injuries.
This symbol indicates a dangerous situation that may
cause slight injuries.
This symbol indicates a situation that may cause
material damage to ePublic.
Work that must be carried out by a technician, from
this point ‘Qualied Personnel’, qualied to design,
create a state-of-the-art domestic electrical system
and certify it in compliance with local regulations and
the energy supply contract.
GB
GB
With respect to the symbols on the product’s nameplate, the wording not shown
above is identied as follows:
1.5. Product dimensions and features
Weight: 48 kg
Dimensions in mm: 1.405 x 422 x 393
Dimensions in inch: 53.3. 16.6 x 11.5.
1
3
4
Top cover Main body
Front panel Anchor plate
9
10
2
Descrizione prodotto
(modello e versione)
Caratteristiche elettriche
Grado di protezione IP e
data di frabbicazione
Part Number
Serial Number
1
2
3
4
1.405
(53,3)
393
(15,4)
422
(16,6
)
GB
GB
With respect to the symbols on the product’s nameplate, the wording not shown
above is identied as follows:
1.5. Product dimensions and features
Weight: 48 kg
Dimensions in mm: 1.405 x 422 x 393
Dimensions in inch: 53.3. 16.6 x 11.5.
1
3
4
Top cover Main body
Front panel Anchor plate
9
10
2
Descrizione prodotto
(modello e versione)
Caratteristiche elettriche
Grado di protezione IP e
data di frabbicazione
Part Number
Serial Number
1
2
3
4
1.405
(53,3)
393
(15,4)
422
(16,6
)
GB
GB
2.
2.2.
2.1.
SAFETY AND EQUIPMENT
Proper use
Avvertenze di sicurezza
Please read this document carefully before installing and starting up the
product.
The installation and start-up phases of the device should only be carried out
by qualied personnel who are able to identify hazards and act safely.
Even the maintenance, repair or subsequent repositioning actions must be
carried out only by qualied personnel: there are no components that can be
repaired by the user or maintained independently.
Children or persons not deemed capable of assessing the risks involved in the
installation must not handle the product.
Both domestic and non-domestic animals must be kept away from the equipment.
Failure to observe all or part of the instructions in this document may lead to
serious or fatal injury.
The qualied installer must always ensure that the installation is carried out in
accordance with the local regulations in eect at the time of installation.
The device requires an earth connection via a dedicated equipotential cable, to be
connected to the earth terminal inside the device.
The device is designed to be connected and to communicate information and
data via a network interface. It is the sole responsibility of the user to provide and
ensure at all times a secure connection between the product and the user’s data
network or any other network (as the case may be).
The user must establish and maintain all appropriate measures (such as, but not
limited to, the installation of rewalls, the application of authentication measures,
data encryption, the installation of anti-virus programs, etc.) to protect the product,
the network, its system and interface against any type of security breach,
unauthorised access, interference, intrusion, loss or theft of data or information.
Free2Move eSolutions S.p.A. and its aliates shall not be liable for any damage or
losses related to any such security breaches, any unauthorized access,
interference, intrusion, loss or theft of data or information.
The data, examples and diagrams in this manual are only included to describe the
product and should not be regarded as a declaration of guaranteed properties.
All persons responsible for installing the equipment specied in this manual must
ensure that each intended installation is suitable and acceptable, including
compliance with any applicable safety or other operational requirements.
In particular, any risk in applications where a system failure or product failure
would create a risk of damage to property or persons (including but not limited
to personal injury or death) shall be the sole responsibility of the person or entity
installing the equipment, and those responsible for it are advised to ensure that all
measures are taken to eliminate or mitigate such risks.
This document has been carefully checked by Free2Move eSolutions S.p.A., but
deviations cannot be completely ruled out. If errors are detected, the reader is
kindly asked to notify Free2Move eSolutions S.p.A.
Except for explicit contractual commitments, under no circumstances may
Free2Move eSolutions S.p.A.r be held liable for any loss or damage resulting from
the use of this manual or from the installation of the equipment.
The product should not be displayed freely on the internet.
In order to ensure maximum security of information and operation, it is necessary
for the device to remain protected from any attempt to connect to it from the
internet. Therefore, any communication should originate only from the device and
not the other way around.
If you require further information, support or wish to make a report regarding
In any case, it is necessary to verify, prior to installation, that the power
supply system is fully compliant with the state of the art and carried out by
qualied personnel in accordance with local and international regulations.
The device is only safe to use if it is used as intended. Dierent uses and
unauthorised modications to the appliance or to any of its components
are not permissible and are therefore considered to be non-compliant.
11
12
2.3. Product handling
When handling, be sure to use a suitable tool that is capable of supporting the
weight of the product.
Transport and store in a dry place away from heat sources (following the
technical guidelines) in the original packaging only
Never grasp the product by the charging cables or connectors.
GB
GB
2.
2.2.
2.1.
SAFETY AND EQUIPMENT
Proper use
Avvertenze di sicurezza
Please read this document carefully before installing and starting up the
product.
The installation and start-up phases of the device should only be carried out
by qualied personnel who are able to identify hazards and act safely.
Even the maintenance, repair or subsequent repositioning actions must be
carried out only by qualied personnel: there are no components that can be
repaired by the user or maintained independently.
Children or persons not deemed capable of assessing the risks involved in the
installation must not handle the product.
Both domestic and non-domestic animals must be kept away from the equipment.
Failure to observe all or part of the instructions in this document may lead to
serious or fatal injury.
The qualied installer must always ensure that the installation is carried out in
accordance with the local regulations in eect at the time of installation.
The device requires an earth connection via a dedicated equipotential cable, to be
connected to the earth terminal inside the device.
The device is designed to be connected and to communicate information and
data via a network interface. It is the sole responsibility of the user to provide and
ensure at all times a secure connection between the product and the user’s data
network or any other network (as the case may be).
The user must establish and maintain all appropriate measures (such as, but not
limited to, the installation of rewalls, the application of authentication measures,
data encryption, the installation of anti-virus programs, etc.) to protect the product,
the network, its system and interface against any type of security breach,
unauthorised access, interference, intrusion, loss or theft of data or information.
Free2Move eSolutions S.p.A. and its aliates shall not be liable for any damage or
losses related to any such security breaches, any unauthorized access,
interference, intrusion, loss or theft of data or information.
The data, examples and diagrams in this manual are only included to describe the
product and should not be regarded as a declaration of guaranteed properties.
All persons responsible for installing the equipment specied in this manual must
ensure that each intended installation is suitable and acceptable, including
compliance with any applicable safety or other operational requirements.
In particular, any risk in applications where a system failure or product failure
would create a risk of damage to property or persons (including but not limited
to personal injury or death) shall be the sole responsibility of the person or entity
installing the equipment, and those responsible for it are advised to ensure that all
measures are taken to eliminate or mitigate such risks.
This document has been carefully checked by Free2Move eSolutions S.p.A., but
deviations cannot be completely ruled out. If errors are detected, the reader is
kindly asked to notify Free2Move eSolutions S.p.A.
Except for explicit contractual commitments, under no circumstances may
Free2Move eSolutions S.p.A.r be held liable for any loss or damage resulting from
the use of this manual or from the installation of the equipment.
The product should not be displayed freely on the internet.
In order to ensure maximum security of information and operation, it is necessary
for the device to remain protected from any attempt to connect to it from the
internet. Therefore, any communication should originate only from the device and
not the other way around.
If you require further information, support or wish to make a report regarding
In any case, it is necessary to verify, prior to installation, that the power
supply system is fully compliant with the state of the art and carried out by
qualied personnel in accordance with local and international regulations.
The device is only safe to use if it is used as intended. Dierent uses and
unauthorised modications to the appliance or to any of its components
are not permissible and are therefore considered to be non-compliant.
11
12
2.3. Product handling
When handling, be sure to use a suitable tool that is capable of supporting the
weight of the product.
Transport and store in a dry place away from heat sources (following the
technical guidelines) in the original packaging only
Never grasp the product by the charging cables or connectors.
GB
GB
3. INSTALLATION
WARNING: Failure to observe the instructions given in this manual may
cause serious damage to both the product and the installer (in the most
serious cases, injuries may be fatal). Please read this manual carefully
before installing, starting up and using the product.
Free2Move eSolutions S.p.A. recommends using experienced professionals
who comply with current regulations in order install the product correctly.
The following table shows the main local restrictions prescribed in the IEC 61851-1
standard that the installer must consider before selecting and installing the device.
However, it remains the responsibility of the installer to verify that these regulations
and could restrict the use of these devices in the country of choice:
Country National restrictions
US Device not suitable for this country
CA Device not suitable for this country
JP Device not suitable for this country
DK
function of the residual current devices must be done by qualified personnel of Free2Move eSolutions S.p.A.
UK
function of the residual current devices must be done by qualified personnel of Free2Move eSolutions S.p.A.
function of the residual current devices must be done by qualified personnel of Free2Move eSolutions S.p.A.
CH
function of the residual current devices must be done by qualified personnel of Free2Move eSolutions S.p.A.
13
14
3.1. Preparing for Installation
Before proceeding with the installation, make sure that:
complete
involved in the work must be prevented
)
Installation should not be carried out with wet hands and no water jet should
be directed towards the product
Installation should not be carried out in rain, fog or high humidity
The product packaging is completely intact and without any obvious damage
(if the product is damaged, contact your seller ask for support on
www.esolutions.free2move.com/ low-power-charging-solutions/ ePublic)
The product and all components (including cables) are completely intact and
without any obvious defects or faults
The installation of the product must comply with all applicable local and
international standards in force for the construction and installation of
electrical/electronic equipment, including, but not limited to, the IEC 60364-1 and
IEC 60364-5-52 standards.
The power supply system must meet the following requirements:
A TN or TT system, in both cases with a PE cable
The entire electrical system to which the product is connected must rst
be correctly sized by a qualied professional. The device’s electrical data,
which should be referred to in order to correctly size the power supply
system, are displayed on the device’s nameplate.
To ensure correct operation of the product in line with the local
regulations in eect, calculate the distance between the power supply
panel and the installation site to determine the voltage drop, cable
thickness and existing load, which are useful for identifying the maximum
operating current.
GB
GB
3. INSTALLATION
WARNING: Failure to observe the instructions given in this manual may
cause serious damage to both the product and the installer (in the most
serious cases, injuries may be fatal). Please read this manual carefully
before installing, starting up and using the product.
Free2Move eSolutions S.p.A. recommends using experienced professionals
who comply with current regulations in order install the product correctly.
The following table shows the main local restrictions prescribed in the IEC 61851-1
standard that the installer must consider before selecting and installing the device.
However, it remains the responsibility of the installer to verify that these regulations
and could restrict the use of these devices in the country of choice:
Country National restrictions
US Device not suitable for this country
CA Device not suitable for this country
JP Device not suitable for this country
DK
function of the residual current devices must be done by qualified personnel of Free2Move eSolutions S.p.A.
UK
function of the residual current devices must be done by qualified personnel of Free2Move eSolutions S.p.A.
function of the residual current devices must be done by qualified personnel of Free2Move eSolutions S.p.A.
CH
function of the residual current devices must be done by qualified personnel of Free2Move eSolutions S.p.A.
13
14
3.1. Preparing for Installation
Before proceeding with the installation, make sure that:
complete
involved in the work must be prevented
)
Installation should not be carried out with wet hands and no water jet should
be directed towards the product
Installation should not be carried out in rain, fog or high humidity
The product packaging is completely intact and without any obvious damage
(if the product is damaged, contact your seller ask for support on
www.esolutions.free2move.com/ low-power-charging-solutions/ ePublic)
The product and all components (including cables) are completely intact and
without any obvious defects or faults
The installation of the product must comply with all applicable local and
international standards in force for the construction and installation of
electrical/electronic equipment, including, but not limited to, the IEC 60364-1 and
IEC 60364-5-52 standards.
The power supply system must meet the following requirements:
A TN or TT system, in both cases with a PE cable
The entire electrical system to which the product is connected must rst
be correctly sized by a qualied professional. The device’s electrical data,
which should be referred to in order to correctly size the power supply
system, are displayed on the device’s nameplate.
To ensure correct operation of the product in line with the local
regulations in eect, calculate the distance between the power supply
panel and the installation site to determine the voltage drop, cable
thickness and existing load, which are useful for identifying the maximum
operating current.
GB
GB
15
16
3.2.
3.3.
Tools required
Package Contents
Cutter
Slotted screwdriver
Ratchet wrenches for hex head screws
Torque wrench
Marker/pencil
Drill and 12mm diameter bit suitable for the material of the xing surface to
be drilled
Hex keys
Wire stripping pliers
N.1 ePublic
1 Anchor plate column base with N.4 M12x105 threaded brackets
2 Keys for opening the front hatch
Product documentation
Free2Move eSolutions S.p.A. accepts no liability for damage to property or
persons deriving from the use of these tools.
Installation must be performed by qualied personnel and in compliance
with the regulations in place for the installation of electrical equipment.
Before installation, ensure that the environmental conditions (such as temperature,
altitude and humidity) comply with the product specications.
To ensure the functionality of the device and to guarantee its proper usage by the
user, the space around the device must be clear to allow for air circulation, proper
and safe cable manoeuvrability, and to allow charging procedures by the user and
both routine and non-routine maintenance operations to be carried out in safe
conditions. In addition, the space needed to park the electric vehicle to be charged
must be taken into account.
In addition:
Make sure that the position and method of installation prevent accidental
impact from manoeuvring vehicles and, if necessary, install barriers or bollards.
Design the parking layout in such a way to ensure easy access to the charging cable.
Provide an environment that is safe and comfortable environment for users
and apt to prevent vandalism or theft.
Install the charging device in a place where it can be clearly seen or monitored;
Install sucient lighting around the device.
3.4. Space and positioning
Make sure that there are no heat sources, ammable substances or
electromagnetic sources in the installation area, either during installation
of the product or throughout the product’s lifetime.
In addition, the installation site must be suciently ventilated to ensure
proper heat dissipation.
For versions of the product with mobile cellular or Wi-Fi connection,
ensure that the selected area has cellular reception or Wi-Fi coverage.
GB
GB
15
16
3.2.
3.3.
Tools required
Package Contents
Cutter
Slotted screwdriver
Ratchet wrenches for hex head screws
Torque wrench
Marker/pencil
Drill and 12mm diameter bit suitable for the material of the xing surface to
be drilled
Hex keys
Wire stripping pliers
N.1 ePublic
1 Anchor plate column base with N.4 M12x105 threaded brackets
2 Keys for opening the front hatch
Product documentation
Free2Move eSolutions S.p.A. accepts no liability for damage to property or
persons deriving from the use of these tools.
Installation must be performed by qualied personnel and in compliance
with the regulations in place for the installation of electrical equipment.
Before installation, ensure that the environmental conditions (such as temperature,
altitude and humidity) comply with the product specications.
To ensure the functionality of the device and to guarantee its proper usage by the
user, the space around the device must be clear to allow for air circulation, proper
and safe cable manoeuvrability, and to allow charging procedures by the user and
both routine and non-routine maintenance operations to be carried out in safe
conditions. In addition, the space needed to park the electric vehicle to be charged
must be taken into account.
In addition:
Make sure that the position and method of installation prevent accidental
impact from manoeuvring vehicles and, if necessary, install barriers or bollards.
Design the parking layout in such a way to ensure easy access to the charging cable.
Provide an environment that is safe and comfortable environment for users
and apt to prevent vandalism or theft.
Install the charging device in a place where it can be clearly seen or monitored;
Install sucient lighting around the device.
3.4. Space and positioning
Make sure that there are no heat sources, ammable substances or
electromagnetic sources in the installation area, either during installation
of the product or throughout the product’s lifetime.
In addition, the installation site must be suciently ventilated to ensure
proper heat dissipation.
For versions of the product with mobile cellular or Wi-Fi connection,
ensure that the selected area has cellular reception or Wi-Fi coverage.
GB
GB
Before installing the device, it is necessary to check, when unpacking, that the
various parts of the device do not display any physical damage due to impacts,
tearing or abrasions.
If any damage is detected, the installation procedure must be aborted immediately
and technical support must be contacted.
The various components are protected by packaging and adhesive tape: before
installation, each component must be cleaned of any traces of dust, packaging or
adhesive tape. The images below are for illustrative purposes and may not show all
internal components of the product or may contain negligible dierences from the
actual conguration.
1. Open the main packaging.
2.
Using appropriate handling equipment, remove the station from the
casing and place it horizontally on the work surface.
3.5. Unpacking
17
18
4. Open the hatch slightly and, using a slotted screwdriver, unhook the
earth cable (yellow/green) from the terminal of the device to which it is
attached.
5. The hatch can be removed completely and the earth cable remains
attached to the hatch.
3. Using the key provided, open the front lock.
Table of contents
Languages:
Other Free2Move eSolutions Automobile Accessories manuals
Free2Move eSolutions
Free2Move eSolutions ProWallbox User manual
Free2Move eSolutions
Free2Move eSolutions eProWallbox User manual
Free2Move eSolutions
Free2Move eSolutions PowerMeter User manual
Free2Move eSolutions
Free2Move eSolutions ProWallbox User manual
Free2Move eSolutions
Free2Move eSolutions eProWallbox Series User manual
Free2Move eSolutions
Free2Move eSolutions eProWallbox User manual
Free2Move eSolutions
Free2Move eSolutions eProWallbox User manual
Free2Move eSolutions
Free2Move eSolutions Annex User manual
Popular Automobile Accessories manuals by other brands
Fortin
Fortin Evo All THAR-CHR4 SUGGESTED WIRING CONFIGURATION
Kia
Kia Rear Seat Entertainment System owner's manual
Ranch Hand
Ranch Hand HBC151BMSL Installation instructions manual
Whispbar
Whispbar K379W Fitting instructions
SSV Works
SSV Works CM-FKP65 user manual
German Autolabs
German Autolabs Chris quick start guide
