Freedom Lift Systems Power EZ User manual

Revised 4/3/17
PART #: APQF-333PEZNA
400 LB. [181 kg] MAXIMUM WEIGHT CAPACITY
MANDATORY
LEAVE THIS MANUAL WITH LIFT OWNER
Read and follow all instructions.
Lift safety can only be ensured if the lift is installed and
operated according to these instructions.
• NEVER permit children to play on or around the lift
• Do not allow children to use the lift without adult
supervision
• NEVER apply direct water pressure to the electronics
• NEVER use the lift with a dry pool
Check entire box and all packing materials for parts. Before beginning assembly, read the
instructions and identify parts using the figures and parts listed in this document.
It is critical that all parts be carefully inspected prior to installation. If any damage occurred in
transit, Freedom Lift Systems must be notified within three days of receipt of unit.
Proper installation cannot be overstressed, as an improper installation voids the
warranty and may aect the safety of the user.
READ CAREFULLY
Power EZ
Pool Lift
1
FREE
OM
Lift Systems
FreedomLiftSystems.com
1-877-947-7769

Revised 4/3/17
Power EZ Components
Power EZ Lift
Table of Contents
PAGE DESCRIPTION PAGE DESCRIPTION
2 Power EZ Components 9 Basic Troubleshooting
3-4 Anchor Installation: Retro-Fit 10 Proper Care of Pool/Spa Lift
5 Anchor Installation: New Construction 11 Parts List
6-7 Assembly Instructions 12 Warranty
8 Operating Instructions 13 Accessories and Options
MAST ASSEMBLY
EZ TURN-BAR
24V BATTERY
24V CONTROL
BOX
BOOM ARM
ASSEMBLY
EZ HANGER
BAR
EZ CHAIN
SET
EZ SLING
LINEAR ACTUATOR
HANDSET
CONTROL
CONTROL BOX
& BATTERY
COVER
BATTERY
CHARGER
EZ ANCHOR
ITEM # QTY DESCRIPTION
1 1 24V LINAK CONTROL BOX
2 1 24V LINAK BATTERY CHARGER
3 1 HARDWARE BAG
4 1 VITO HANDSET REMOTE
5 1 24V LINAK BATTERY
6 1 EZ SLING [F-034EZS]
7 1 EZ CHAIN SET [F-031EZCH]
8 1 EZ HANGER [F-038EZHB]
9 4 EZ SLING BARS [F-032EZB]
10 1 LINEAR ACTUATOR [340461-00]
11 1 EZ TURN BAR [A-0808EZTB]
12 1 CB/BATTERY COVER [F-BCC-10-C]
13 2 3/8” X 1 3/4”HEX BOLT
14 2 3/8” NYLOCK NUT
15 4 3/8” FLAT WASHER
16 2 2 1/4” HOSE CLAMP
17 3 ZIP TIES
18 1 ANCHOR (IF ORDERED WITH LIFT)
19 1 OWNERS MANUAL
ITEM # QTY DESCRIPTION
1 1 POWER EZ BOOM ARM & MAST
BOX ‘A’ CONTENTS
BOX ‘B’ CONTENTS
The Power EZ lift will arrive partially assembled in multiple boxes. Begin by removing all parts from
the boxes and locating the parts for your lift in the parts lists below. Refer to the parts breakdown
drawings in the back of this manual for assistance.
2

Revised 4/3/17
Anchor Installation: Retro-Fit Concrete
NOTE: The concrete deck around the
anchor should be a minimum of 8 inches
thick and reinforced with #4 bars at 10
inches on center, each way. The total
concrete pad area should be at least 60
inches wide and 60 inches long.
TOOLS REQUIRED:
TAPE MEASURE 4” CORE DRILL BIT
CORE DRILL FELT TIP MARKING PEN
ELECTRICAL TAPE VACCUM OR COMPRESSED AIR
CARPENTERS LEVEL 2-PART EPOXY (or equivalent)
1. Determine the best location for the lift. Mount the lift at a location that provides 42 inches [107cm] to
48 inches [122cm] deck level to the bottom of the pool (usually the shallow end). Make sure the location
has enough clear deck space to easily transfer. The lift requires at least 6 feet [1.8 meters] of unobstructed
deck to each side of the lift to accomodate easy maneuvering of the lift over the water and back. Keep in
mind this lift will require assistance so locate an area that can accomodate another person.
2. Locate the concrete anchor socket that came with your lift. Be careful to not lose the protective cap
on the anchor as this will be used to keep dirt and debris out of the socket when the lift is not installed in
the anchor.
3. The setback to the center of the anchor must be no less than 12 inches [30.5cm] and no more than
20 inches [51cm] from the pool wall. The anchor location must also be at least 6 inches [15cm] from any
control joint or edge of concrete slab. Measure the location out using the tape measure and marking
pen. See FIGURE 1 on page 4 for details.
4. Core drill at least a 4 inch [10cm] diameter hole at the desired location for the lift anchor socket.
The hole will need to be 7 inches [18cm] deep to allow for the grounding lug which protrudes from the
bottom of the anchor.
NOTE: Use the electrical tape to make a mark on your drill bit at 7 inches [18cm] as a depth mark to
tell you when to stop drilling.
5. Clean out the hole using a vaccum or compressed air. Check that the hole is deep enough to allow
6. Ground the anchor according to your local code requirements. This may require additional drilling
and/or other tools.
3

Revised 4/3/17
Anchor Installation: Retro-Fit Concrete
7. Carefully insert the anchor into the hole. Pour a small amount of 2 part epoxy, or equivalent, around
NOTE: Fill the hole about 1/3 full of 2 part epoxy, or equivalent, prior to inserting the anchor. As
you insert the anchor, rotate it back and forth so that you can evenly distribute the cement
or epoxy around the anchor.
8.
the anchor making sure there are no void spaces. Let cement or epoxy cure for 24 hours (or minimum
manufacturer’s recommendations) before installing and using lift.
[20.3cm]
8" MIN.
[51 cm] 20" MAX
[30.5 cm] 12" MIN
[15 cm]
6" MIN
[107cm]
42"
TO
[122cm]
48"
C
L
ANCHOR SOCKET
TOP OF SLAB
GROUNDING LUG
CEMENT/EPOXY
FIGURE 1
4

Revised 4/3/17
Anchor Installation: New Construction
NOTE: The concrete deck around the anchor should be a
minimum of 8 inches thick and reinforced with #4 bars at
10 inches on center, each way. The total concrete pad area
should be at least 60 inches wide and 60 inches long.
TOOLS REQUIRED:
TAPE MEASURE STRING LINE
CARPENTERS LEVEL STRING LEVEL
MARKING PEN
1. Determine the best location for the lift. Mount the lift at a location that provides 42 inches [107cm] to
48 inches [122cm] deck level to the bottom of the pool (usually the shallow end). Make sure the location
has enough clear deck space to easily transfer. The lift requires at least 6 feet [1.8 meters] of unobstructed
deck to each side of the lift to accomodate easy maneuvering of the lift over the water and back. Keep in
mind this lift will require assistance so locate an area that can accomodate another person.
2. Locate the concrete anchor socket that came with your lift. Be careful to not lose the protective cap
on the anchor as this will be used to keep dirt and debris out of the socket when the lift is not installed in
the anchor.
3. The setback to the center of the anchor must be no less than 12 inches [30.5cm] and no more than
20 inches [51cm] from the pool wall. The anchor location must also be at least 6 inches [15cm] from any
control joint or edge of concrete slab. Measure the location out using the tape measure and marking
pen. See FIGURE 1 on page 4 for details.
4. Ground the anchor according to the local code requirements.
5. Place the anchor in the proper location using the string level and string line to make sure the top of
the location of the anchor to hold it in place.
6. Verify all the measurements for accuracy and pour the deck as you normally would, making sure not
to get any concrete inside the anchor system. Allow the concrete to cure before installing and using the
lift.
5

Revised 4/3/17
CONTROL BOX
AND BRACKET
CONNECT TOP
AND BOTTOM
TABS TO THE
HOSE CLAMPS
HOSE
CLAMP (2)
STEP 1
Assembly Instructions
TOOLS REQUIRED:
9/16”WRENCH 3/4”WRENCH
1/8” HEX KEY FLATHEAD SCREWDRIVER
The Power EZ Pool Lift arrives with the boom arm attached
to the mast. To complete the assembly, layout all parts on a
large, clean area.
STEP 1. Attach the control box to the lifts mast using the
STEP 2. Connect the lower end of the electric actuator to
the mast (vertical post) with one (1) 3/8” x 1 3/4” hex bolt,
STEP 3. Connect the upper end of the actuator to the
washers and one (1) 3/8” nylock nut.
STEP 4. Slide the lift into the previously installed anchor
socket. Make sure that the mast is seated at the bottom of
the anchor. Check to ensure easy rotation of the lift inside
the nylon-lined anchor sleeve.
NOTE: Three (3) zip ties shipped with the Power EZ Lift.
These are meant to secure excess actuator cable. Failure to
complete this may cause a tripping hazard. See the pictures
below on how to attach the cable to the lift.
MAST
3/8" X 1 3/4"
HEX BOLT
3/8" FLAT
WASHER (2)
3/8"
NYLOCK
NUT
STEP 2
ACTUATOR
3/8"
NYLOCK
NUT
3/8" X 1 3/4"
HEX BOLT
3/8" FLAT
WASHER (2)
BOOM
ARM
STEP 3
6

Revised 4/3/17
Assembly Instructions
STEP 5. Locate the chain assembly and insert each “S” hook
into the holes in the sling support bars (A).
Attach the hanger to the boom eye on the lift (B).
Adjust the chain links so that the sling is at the
appropriate height to allow the user easy access (C).
This may require several adjustments. Also, be
mindful of any obstacles such as coping or a gutter
that will need to be cleared.
STEP 6. Attach the handset controller plug at the base of
control box.
STEP 7. Slide the EZ turn bar into the attachment bracket.
Mount the FULLY CHARGED 24V battery on top of the control
box. When properly mounted the battery will lock in place,
control box.
ATTENTION! THE BATTERY MUST BE CHARGED FOR 24
HOURS BEFORE FIRST USE. STORE THE BATTERY ON THE
CHARGER AND NEVER LEAVE THE BATTERY ON THE LIFT
WHEN NOT IN USE.
Assembly is complete. Prior to lifting any persons, it is
recommended that the lift be operated once without a load
to check for proper functioning (and that the instructions for
operating the lift be read and incorporated into a training
program for the persons who will be operating the lift). For
any person operating the lift, please continue to operating
instructions. Read carefully for comprehension.
STEP 6
24V BATTERY
(CHARGED)
EZ TURN BAR
STEP 7
STEP 5
A
B
C
7

Revised 4/3/17
Operating Instructions
NOTE: For safety, check for worn parts and loose bolt connections prior to each use. All operators
should be familiar with all lift components and their intended uses. Operators should also be
comfortable with all lifting procedures before attempting to lift a person with the lift.
The Power EZ Pool Lift requires the use of an operator to assist the lift occupant with the transfer into the
pool. There are two methods of loading the lift occupant into the harness. The method of loading will
depend on the physical ability of the lift occupant. If the user is physically able, he/she can simply place
themself into the harness without need for assistance. If the user has very limited use of his/her upper
body, it will be necessary to follow the procedure below.
1. With the lift in the raised position and the boom arm located over the deck, roll the user under the lift
and engage the brakes on the wheelchair.
2. With the user facing the assistant, gently slide the mesh seat sling under the seated user while still in
the wheelchair.
3. Attach the chain to the mesh sling and the overhead hanger bar. Avoid excess slack in the chain.
4. Ensure all chain connections are secure and the mesh seat sling is even on each side of user.
5. Raise the user by pressing the ‘up’ arrow button on the handset until the desired height is achieved.
6. Rotate the lift so that the user is above the pool. Never push on the actuator! Use the turn bar or
place one hand on the boom arm and one hand on the mast.
7. Lower the user into the water by pressing the ‘down’ arrow button on the handset until the user is
8. This procedure is repeated to remove a user from the water.
9. When the lift is not in use, remove the sling, hanger bar and mast from the anchor socket and replace
the protective cap.
8

Revised 4/3/17
Basic Troubleshooting
Problem: The lift won’t move.
Solution:
1. Make sure the battery is properly seated:
You should hear a click when
the battery is properly seated
on the control box or charger.
Click!
NOT Properly Attached:
Note: the white bracket is
in front of the silver clip,
which will not allow for
an electrical connection
Properly Attached:
Note: the white bracket
is behind the silver clip,
holding it securely to
allow for an electrical
connection
Check the ends of the cords for corrosion or
damage. The cord plugs should be recessed
into the outlet. You should feel them pop into
place when they are correctly inserted.
2. Make sure the cords are properly plugged in:
NOT Properly Inserted:
The cord plug is flush with
or sticking out of the outlet
Properly Inserted:
The cord plug is recessed
into the outlet
POP!
The Charger is ON
when the green
light is glowing
The Battery is
CHARGING when the
orange light is glowing
When the Battery is
charged the orange
light will stop glowing
4. Make sure the battery is fully charged:3. Check the contact points:
Make sure the contact points of
the control box and the battery
are not damaged or corroded.
If there is corrosion clean with
Scotch-Brite TM pad. Put some
dielectric grease on the contact
points before reattaching the
battery.
Problem: The lift stopped moving over the water and is stuck.
Solution:
1. Press the emergency button
Use a pen or pencil tip and
stick it into the emergency
button on the front of the
control box to retract the lift.
Note: the lift will not retract
if the battery is not fully
charged or if the control box
is not working. The emergency
button only overrides the
remote handset.
9

Revised 4/3/17
Proper Care of Pool & Spa Lifts
PROCEDURE DAILY WEEKLY MONTHLY
Wash down lift with fresh water and dry with clean, soft,
non-abrasive cloth. ü
Recharge battery. ü
Run the lift through a complete test cycle to verify it is
functioning properly. ü
Visually inspect lift for damage, corrosion, and loose or
missing hardware. ü
Check all contact points for damage and/or corrosion. ü
Repair, clean, and apply dielectric grease to all contact
points. ü
Thoroughly clean lift frame and apply a liberal coat of car ü
Check all Warning and Cautionary labels to make sure they
are not faded or worn. Replace as needed. ü
PROPER CARE NOTES
• Use only fresh water to wash your lift. Do not wash with pool water.
• Use only clean, soft, non-abrasive cloths to wipe down your lift.
• Do not store lift in pump room or near chemicals.
• Do not allow children to play on or around this lift.
• When cleaning the lift, do not spray water directly on control box or battery.
• The lift may need to be bonded according to local code requirements.
wax to protect when dry.
STAIN REMOVAL TIPS:
10

Revised 4/3/17
ITEM # QTY PART # DESCRIPTION
1 1 PEZWM-0804PEZMA MAST WELDMENT, POWER EZ
2 1 PEZWM-0804PEZBA BOOM WELDMENT, POWER EZ
3 1 340643-00 ACTUATOR, LINAK, LA-34
4 1 F-038EZHB HANGER BAR, STANDARD
5 1 F-034EZS EZ STANDARD SLING
6 1 F-032EZB SLING BARS ONLY, SET OF 4
7 1 F-031EZCH CHAIN SET, EZ
8 1 A-0808EZTB EZ TURN BAR
9 2 CCF-1 3/4-14-20 PLUG, 1 3/4 ROUND, PLASTIC, BLACK, .065 WALL
10 1 RUBBER HAND GRIPS GRIP, RUBBER HAND GRIP
11 2 HOSE CLAMPS, 2 1/4 SS HOSE CLAMP, 2 1/4”, SS
12 2 BH 3/8 X 1 3/4 BOLT, 316 SS, 3/8-16 X 1 3/4 HCS
13 5 WF 3/8 WASHER, FLAT, 3/8, 316 SS
14 3 NN 3/8 NUT, 316 SS, NYLOCK, 3/8”-16
15 1 BS 1/2 X 2 1/4 18-8 BOLT, 18-8 SS, 1/2 X 2 1/4 SHOULDER, 3/8-16 THREAD
16 2 BRB SS-1620-3 BUSHING, BRONZE SLEEVE, SS-1620-3, 1/2 X 5/8 X 3/16
17 1 BRB SS-1216-4 BUSHING, BRONZE SLEEVE, SS-1216-4, 3/8 X 1/2 X 1/4
18 1 F-BCC-11 COVER, BATTERY/CONTROL BOX, BLUE
19 1 MBJ2-01 BRACKET, MOUNTING, T-SHAPED
20 1 CBJ2-U022-00 CONTROL BOX, SINGLE PORT, LINAK
21 1 WF 10 WASHER, FLAT, #10 SAE, 316 SS
22 1 BSH 10 X 3/8 BOLT, 316 SS, 10-24 X 3/8 SHCS
23 1 BAJ1-U022-00 BATTERY, LINAK, 24 VOLT
24 3 ZIP TIE, 6” 6” CABLE ZIP TIE
Parts List
1
13
12
8
10
19
20
22
21
23
11 15 16 913 14 2
12
13
13 14
9
3
14
13
17
4
7
6
5
18
11

Revised 4/3/17
Revised_1.2.2017
AQUA CREEK PRODUCTS, LLC LIMITED FIVE (5) YEAR WARRANTY :
EZ SERIES LIFTS
(ITEM #’s : F-03EZPLNA, F-333PEZNA, F-194PHBL-NA)
Aqua Creek Products, LLC (a.k.a. Aqua Creek) warrants to the original end user purchaser that products manufactured by Aqua
Creek, when properly installed in accordance with assembly and installaon instrucons, and properly used and maintained, s hall be
free from defects in material and workmanship for a period of ve (5) years from the date of original purchase, provided that Aqua
Creek receives prompt noce in wring of any defect or failure and sasfactory proof thereof, with the following excepon (s):
Exceptions:
All electrical components, including the linear actuator shall have the following warranty period:
oYear 1-2: 100% Coverage
oYear 3: 60% Coverage (Customer is responsible for 40% of replacement cost)
oYear 4: 50% Coverage (Customer is responsible for 50% of replacement cost)
oYear 5: 40% Coverage (Customer is responsible for 60% of replacement cost)
Hydraulic actuators and mesh slings shall have a warranty period of one (1) year from the date of original purchase .
Powder coat finish scratches, scrapes, corrosion, or dents from customers normal use, negligence, or abuse
This warranty specifically excludes reimbursement for labor to remove, repair, or install the product and any shipping charges.
These warranes do not cover any damages due to accident, misuse, abuse, negligence or failure to properly maintain any prod ucts,
or normal wear and tear from day to day operaons. In the event that any products are altered, repaired, or improperly installed or
improperly used by anyone without the prior wrien approval by Aqua Creek, all warranes are void. IMPORTANT: AMOUNT OF
WEIGHT PLACED ON LIFT SHALL NOT EXCEED THE RATED LIFTING CAPACITY FOR THE LIFT. NEVER OPERATE THE LIFT UNDER LOAD IN
A DRY POOL (WITH NO WATER IN THE POOL). It is the responsibility of the liowner to verify the weight of the patron for warranty
claim purposes and to ensure that the liis not overloaded. Non-payment for product to Aqua Creek may void warranty.
To iniate a warranty claim, the owner of an Aqua Creek product must provide the place of purchase, in wring, with a full
descripon of the product, its serial number, the dates of purchase and installaon, and the exact nature of the defect. Within thirty
(30) days aer receipt of a wrien warranty claim by Aqua Creek, and barring any unforeseen delays, the place of purchase w ill be
nofied of Aqua Creek’s decision regarding the claim.
If requested by Aqua Creek, any defecve product must be returned, freight prepaid by customer, to Aqua Creek’s designated
factory locaon or duly appointed distributor for inspecon and/or repair. Aqua Creek will, at its opon, repair or replace the failed
or defecve item, and deliver the repaired product or replacement to the customer. All freight charges are the responsibility of the
customer. Products returned to Aqua Creek for which Aqua Creek provides replacement under this limited warranty shall become
the property of Aqua Creek. A new warranty period shall NOT be established for the repaired or replaced products. Such products
shall remain under warranty only for the remainder of the original warranty period on the original products purchased.
This wrien limited warranty constutes the final, complete and exclusive statement of warranty terms. No person or organiz aon
is authorized to make any other specific or implied warranes or representaons on behalf of Aqua Creek.
THE WARRANTIES SET FORTH HEREIN ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, WHICH ARE HEREBY DISCLAIMED AND EX CLUDED,
INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR US E.
THE SOLE AND EXCLUSIVE REMEDIES FOR BREACH OF ANY AND ALL WARRANTIES WITH RESPECT TO THE PRODUCTS SHALL BE LIMITED TO REPAIR OR
REPLACEMENT AT AQUA CREEK’S DESIGNATED FACTORY LOCATION, OR DULY APPOINTED DISTRIBUTOR, OR IN PLACE AT AQUA CREEK’S OPTION. IN NO EVENT
SHALL AQUA CREEK’S LIABILITY EXCEED THE ENTIRE AMOUNT PAID TO AQUA CREEK BY THE ORIGINAL PURCHASER FOR THE FAILED OR DEFECTIVE PRODUCT.
IN NO EVENT SHALL AQUA CREEK PRODUCTS, LLC BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, INDIRECT,PUNITIVE OR EXEMPLARY DAMAGES OR
LOST PROFITS FROM ANY BREACH OF THIS LIMITED WARRANTY OR OTHERWISE.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH MAY VARY FROM STATE TO STATE. SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, SO SOME OF THE ABOVE LIMITATIONS OR EXCLUSIONS MAY
NOT APPLY TO YOU.
Aqua Creek Products, LLC
Toll Free: (888) 687 -3552
12

F-EZBL-C EZ/ Power EZ
F-4440HBC-B Super Power EZ
F-440EZHSC EZ/ Power EZ
(cover for hardseat option)
F-BCC-11 Control Box Cover
(Power EZ)
F-SPEZBC Control Box Cover
(Super Power EZ)
COVERS ANCHORS
SOLAR CHARGER
EZ SERIES ACCESSORIES
SLING ACCESSORIES & OPTIONS
UPGRADE PACKS
F-035EZSM Surface Mount
F-30600 Wood Deck Mount
F-046SCH Power EZ (only)
F-032EZSB Sling Assembly w/Bars, Standard Adult Size (38” L x 20” W)
F-036RSS Sling Assembly w/Bars, Rigid Insert & Seat Belt, Standard Adult Size (38” L x 20” W)
F-037EZLS Sling Assembly w/Bars, Extra Long Size (50” L x 20” W)
F360YSLSB Sling Assembly w/Bars & Seat Belt, Youth Size (34” L x 18” W)
F-037XXLS Sling Assembly w/Bars, 500 lb. Capacity, Extra Long (50” L x 39.5” W)
F-034EZS Sling Only, Standard Adult Size (38” L x 20” W)
F-032EZB Sling Bars Only, Set of 4 ( Compatible with all Slings)
F031EZCH Chain Set, Standard Replacement, EZ/PEZ/SPEZ
F-03EZHB4P 4-Point Hanger Bar
F-038EZHB Standard Hanger Bar, Replacement
F-0320HSO-4C Hard Seat Option w/Chain Assembly, EZ/PEZ/SPEZ
F-03PEZAP Power EZ (sling bars, rigid seat, sling w/seat belt, cover, extra battery)
F-190PHBLAP Super Power EZ (sling bars, rigid seat, sling w/seat belt, cover, extra battery)
EZ & Power EZ Only