Fremco MicroFlow TOUCH User manual

Valid from 01.07.2021 | Rev. 1.0
From Serial No. 9328.2294
FREMCO A/S
ELLEHAMMERVEJ 14 |DK9900 FREDERIKSHAVN, DENMARK |VAT NO.: DK30815416
TELEPHONE [phone] |[email protected] |WWW.FREMCO.DK
THIS MATERIAL IS COPYRIGHT PROTECTED
Operating manual
Responsible manufacturer: Fremco A/S
Machine: MicroFlow TOUCH & MicroFlow LOG
This is the original operating manual for MicroFlow TOUCH and MicroFlow LOG from
Fremco.
MicroFlow TOUCH MicroFlow LOG
For fiber dimension 0.8-6.5 mm For fiber dimension 0.8-6.5 mm

Page | 2 of 40
FREMCO A/S
ELLEHAMMERVEJ 14 |DK9900 FREDERIKSHAVN, DENMARK |VAT NO.: DK30815416
TELEPHONE [phone] |[email protected] |WWW.FREMCO.DK
TABLE OF CONTENT
1. INTRODUCTION ........................................................................................................................ 4
2. GENERAL .................................................................................................................................. 5
2.1. MANUFACTURER....................................................................................................... 5
2.2. THE MACHINE’S DESIGNATION............................................................................... 5
2.3. MACHINE PLATE........................................................................................................ 5
3. TECHNICAL SPECIFICATIONS................................................................................................ 6
4. SAFETY INSTRUCTIONS.......................................................................................................... 7
5. MAINTENANCE ......................................................................................................................... 9
6. APPLICATION ......................................................................................................................... 10
7. MOUNTING AND PREPARATIONS........................................................................................ 10
8. SUPPLY OF COMPRESSED AIR AND ELECTRICITY.......................................................... 11
9. FIBER PROTECTION TECHNOLOGY.................................................................................... 11
10. MICROFLOW TOUCH CONTROLLER ................................................................................... 12
10.1. DISPLAY SYMBOLS................................................................................................. 13
10.2. RUNNING THE FIBER BLOWING MACHINE .......................................................... 14
10.3. USE OF “TOUCH” CONTROL UNIT ......................................................................... 15
10.3.1. ADJUSTABLE PARAMETERS.............................................................................. 15
10.4. TOUCH DISPLAY SCREEN OVERVIEW................................................................. 16
11. MICROFLOW LOG CONTROLLER ........................................................................................ 19
11.1. DISPLAY SYMBOLS................................................................................................. 20
11.2. RUNNING THE FIBER BLOWING MACHINE .......................................................... 21
11.3. USE OF “LOG” CONTROL UNIT .............................................................................. 24
11.3.1. ADJUSTABLE PARAMETERS.............................................................................. 25
11.4. LOG DISPLAY SCREEN OVERVIEW ...................................................................... 25
11.5. CONFIGURATION AND UPDATE OF TABLET AND CONTROLLER..................... 30
11.6. RESET TABLET TO FACTORY DEFAULT .............................................................. 33
11.7. OPTICLOUD –ONLINE FIBER DATABASE ............................................................ 35
12. TORQUE OFF-SET.................................................................................................................. 38
13. ADAPTOR PLATES................................................................................................................. 38
14. EC DECLARATION OF CONFORMITY .................................................................................. 39
15. UKCA DECLARATION OF CONFORMITY............................................................................. 40

Page | 3 of 40
FREMCO A/S
ELLEHAMMERVEJ 14 |DK9900 FREDERIKSHAVN, DENMARK |VAT NO.: DK30815416
TELEPHONE [phone] |[email protected] |WWW.FREMCO.DK
BEST WARRANTY IN THE BUSINESS
We offer a unique 36 months warranty on all our fiber blowing machines resulting,
guaranteeing you the best value for your money.
Our 12 months warranty is automatically included when you purchase your Fremco fiber
blowing machine, you automatically get our 12 months warranty. You can then claim your
additional 24 months warranty at any point during the following three months in order to
obtain the best cost-beneficial warranty in the business.
To maintain your 36 months warranty, you must meet the given annual service and
maintenance requirements for each machine as described in the operating manual.
Learn more at www.fremco.dk/warranty and
get the best factory warranty in the business today!

Page | 4 of 40
FREMCO A/S
ELLEHAMMERVEJ 14 |DK9900 FREDERIKSHAVN, DENMARK |VAT NO.: DK30815416
TELEPHONE [phone] |[email protected] |WWW.FREMCO.DK
1. INTRODUCTION
Original instructions
These instructions are Fremco A/S’ original instructions for the MicroFlow TOUCH and/or
MicroFlow LOG (hereafter called the machine).
Purpose
The purpose of these instructions is to ensure correct installation, use, handling and
maintenance of the machine. Applicable from machine serial number 9328.2294.
Accessibility
The instructions are to be kept in a location known to the staff and must be easily accessible
for the operators and maintenance personnel.
Knowledge
It is the duty of the employer (the owner of the machine) to ensure that everybody
operating, servicing, maintaining, or repairing the machine reads and understands the
instructions. As a minimum, they should read the part(s) relevant to their work.
In addition to this, everybody operating, servicing, maintaining, or repairing the machine is
obliged to seek out information in the operating manual when needed.

Page | 5 of 40
FREMCO A/S
ELLEHAMMERVEJ 14 |DK9900 FREDERIKSHAVN, DENMARK |VAT NO.: DK30815416
TELEPHONE [phone] |[email protected] |WWW.FREMCO.DK
2. GENERAL
2.1. MANUFACTURER
The machine is manufactured by
Company name: Fremco A/S
Company address: Ellehammervej 14
DK-9900 Frederikshavn
2.2. THE MACHINE’S DESIGNATION
The machine’s complete designation is MicroFlow TOUCH or MicroFlow LOG.
2.3. MACHINE PLATE
The machine plate is situated on the back of the machine:
Figure 1: Location of machine plate
Model: MicroFlow LOG
Year: 2020 Serial No.: 1234.9876
Pmax air: 16 (230)
Bar (psi)
Figure 2: Location of the UKCA sticker is
placed next to the machine plate

Page | 6 of 40
FREMCO A/S
ELLEHAMMERVEJ 14 |DK9900 FREDERIKSHAVN, DENMARK |VAT NO.: DK30815416
TELEPHONE [phone] |[email protected] |WWW.FREMCO.DK
3. TECHNICAL SPECIFICATIONS
These specifications cover MicroFlow TOUCH and MicroFlow LOG as well as the control unit and the adaptor
plates belonging to it. The adaptor plates are replaceable and must fit the actual size of fiber cable and
microduct to be used.
Manufacturer Fremco A/S
Ellehammervej 14
9900 Frederikshavn
Denmark
Item No............................................................................................................... 101-10051(Touch) / 101-171001001 (LOG)
Fiber cable diameter ..................................................................................................................................................... 0.8-6.5 mm
Microduct diameter .......................................................................................................................................................... 4-16 mm
Blowing speed1............................................................................................................................Up to 90 m/min. (295 ft/min.)
Maximum air pressure...........................................................................................................................................16 bar (230Psi)
Maximum air temperature .........................................................................................................................................60°c (140°f)
Ambient temperature........................................................................................................................................0-40°c (32-104°f)
Recommended air pressure and flow¹:.......................................8-16 bar (120-230 psi), 200-500 l/min. (7.1-17.7 cfm)
Power Supply..................................................................................................24V DC. Can be connected to 100-240V AC,
50/60 Hz with the included transformer.
100-240V AC power supply must be stable and at least 2A.
Weight......................................................................................................................................................................9.7 kg (21.4 lbs)
Length ......................................................................................................................................................................... 250 mm (9.8”)
Width.......................................................................................................................................................................... 150 mm (5.9”)
Height ......................................................................................................................................................................... 220 mm (8.7”)
Control unit weight ................................................................................................................................................1.9 kg (4.2 lbs)
Control unit length ................................................................................................................................................. 200 mm (7.9”)
Control unit width .................................................................................................................................................. 150 mm (5.9”)
Control unit height ................................................................................................................................................... 80 mm (3.1”)
MicroFlow in carrying case, weight/dimension ...............................................................................................23 kg (50.7 lbs)
600x400x350 mm (23.6”x15.7”x13.8”)
¹Depending on type and quality of fiber and microduct
2Cooled and dried compressed air

Page | 7 of 40
FREMCO A/S
ELLEHAMMERVEJ 14 |DK9900 FREDERIKSHAVN, DENMARK |VAT NO.: DK30815416
TELEPHONE [phone] |[email protected] |WWW.FREMCO.DK
4. SAFETY
INSTRUCTIONS
•Read and understand this operating manual
before operating the MicroFlow. Follow all
safety instructions. Failure to follow the
instructions may lead to damage on the
machine and mild to severe personal injury.
•All operators must have relevant technical
training, or have undergone thorough training
by an experienced operator.
•Always use protective eye wear.
•Always wear safety shoes.
•Never wear loose clothing.
•Make sure to disconnect the machine from the
air compressor and the power supply, before
any kind of adjustment and maintenance takes
place.
•The air pressure should never exceed the
recommendations from the suppliers of
microducts and fiber. The pressure may never
exceed machine maximum pressure: 16 bar,
which is the maximum pressure for the
MicroFlow blowing machine.
WARNING: Exceeding max
pressure may lead to machine damage
and mild to severe personal injury.
•Open lid: Do not operate the machine with an
open lid due to risk of getting in contact with
moving parts.
WARNING: Operation with an
open lid may lead to personal injury.
•Protective covers: Do not remove the
protective covers of the machine for daily use.
Protectives covers must only be removed by
authorized personnel for service and
maintenance, and only if power and
compressed air supply is disconnected.
After all kind of service and maintenance,
protective covers must be put back in place
and secured properly with all screws before
operating.
WARNING: Operation without
protective covers may lead to
machine damage and personal injury.
•Pressurised components must be undamaged
and intended for use within the machine’s
pressure and temperature range. Daily visual
inspection is necessary to avoid failure.
WARNING: Use of damaged
pressurised components (e.g. hoses,
pipes, ducts, connectors) may lead to machine
damage and mild to severe personal injury.
Daily visual inspection is necessary to avoid
failure.
•Electronic components must be undamaged.
Daily visual inspection is necessary to avoid
damaged electronic components.
WARNING: Use of damaged
electronic components (wiring,
enclosures) may lead to personal injury.
•Exhaust of dust and particles:
The operator must ensure that neither
operator nor spectators are exposed to the
danger of exhaust of dust and particles, and
the operator must ensure that the duct is
fastened correctly.
WARNING: Exhaust air can
contain objects, dust and particles
that may be ejected from duct and machine
during the blowing process. This may lead to
eye or other personal injury. Always use
protective eye wear.
•Ejection of pressurised components: The
operator must ensure that duct and other
pressurised components and utilities are
fastened correctly.

Page | 8 of 40
FREMCO A/S
ELLEHAMMERVEJ 14 |DK9900 FREDERIKSHAVN, DENMARK |VAT NO.: DK30815416
TELEPHONE [phone] |[email protected] |WWW.FREMCO.DK
WARNING: Insufficient
fastening/connections of ducts or
other pressurised components may lead to
ejection of parts, which may lead to personal
injury.
•Always place the machine on a stable
foundation, to secure it from falling during
operation.
WARNING: Loss of stability:
If machine is not placed on stable
foundation, machine can loss its stability and
fall, causing damage to machine and mild to
severe personal injury.
Always use safety shoes.
•Make sure that the fiber and duct are placed
correctly in the machine.
•Make sure not touch the fiber too close to the
machine due to the risk of injuries to fingers,
and make sure the fiber does not make loops
that might be dangerous to persons around
the machine.
•Never wear loose clothing
WARNING: Loose clothing may
become entangled in the machine.
•Use hearing protection, if the air compressor
is placed nearby.
•The operator must make sure that no other
persons are close to the machine and cable
drums in a way that could be dangerous when
the machine is started.
•It is always a clear advantage to be well
prepared so that you can run the blowing
without interruptions. Pausing in the middle of
blowing creates a risk of being unable to start
again.
•Make sure the working environment is clean
and tidy to avoid injuries due to stumbling
over fiber and equipment.
Intended/Unintended Use
The machine is intended for installation of fiber
optic cables into ducts by blowing with
compressed air and nothing else. Do not use the
machine for other purposes.
Examples of unintended use may be:
•Exceeding max pressure may lead to machine
damage and mild to severe personal injury.
•Use of other media than compressed
atmospheric air for the blowing process can
lead to machine damage or personal injury.
•Use of machine outside its specifications (eg.
use for fibers or ducts larger/smaller than
specified) may lead to a poor job performance
or machine damage.
•Use of wrong size fiber/duct adaptor can lead
to ducts under pressure being blown out of
machine, which may cause personal injury and
machine damage.
WARNING: Unintended use of
machinery may lead to personal
injury, machine failure or damage to the
machine.
•Noise: necessary measures must be taken to
reduce noise at the workplace to an
acceptable level. The discharge of compressed
air from the machine may cause noise level to
increase. Using the wrong gasket size can
increase noise level. Wear on gaskets can also
result in increased noise level. In addition to
noise generated by the Microflow machine,
consideration must also be given to additional
process equipment (e.g. compressors). If
machine is used correctly, the noise level
should not exceed the allowed noise level, but
if the noise level is above permitted limit value
(EU Limit Value 80 db), hearing protection
should be used.
WARNING: Noise above limit
values may cause permanent damage
to hearing.

Page | 9 of 40
FREMCO A/S
ELLEHAMMERVEJ 14 |DK9900 FREDERIKSHAVN, DENMARK |VAT NO.: DK30815416
TELEPHONE [phone] |[email protected] |WWW.FREMCO.DK
•External cleaning: Cleaning of the machine
should be done on a daily basis. Do not clean
the machine while the machine is running.
•Internal cleaning, service and repair: Service
and repair must only be done by qualified
technicians, and only if power and compressed
air supply is disconnected. Do not remove the
protective covers of the machine for daily use.
Protectives covers must only be removed by
authorized personnel for service and
maintenance. After all kind of service and
maintenance protective covers must be put
back in place and secured properly with all
screws before operating.
WARNING: Operation without
protective covers may lead to
machine damage and personal injury.
•If an accident occurs, do as follows:
Stop the accident by turning off power and
compressed air supply.
Find the necessary help.
5. MAINTENANCE
Compressed air must be clean and dry. Use air filter and water separator.
Clean the wheels on a regular basis, at least once a day when the machine is in use.
Make sure the sensor arms are clean and can move freely.
Check gaskets and rubber belts on wheels for wear and tear on a daily basis and replace if necessary.
Machine service is required annually or every 350 km depending on what comes first.
NB: Humid and polluted air may influence
machine life and performance and may result in
increased wear.
NB: Failure to maintain and clean the machine
may affect machine reliability.
NB: To maintain your 36-months warranty, you
have to meet the given service requirements.

Page | 10 of 40
FREMCO A/S
ELLEHAMMERVEJ 14 |DK9900 FREDERIKSHAVN, DENMARK |VAT NO.: DK30815416
TELEPHONE [phone] |[email protected] |WWW.FREMCO.DK
6. APPLICATION
The fiber blowing machines MicroFlow TOUCH and MicroFlow LOG are constructed for blowing fiber optic
cables with a diameter of 0.8 to 6.5 mm into microducts with an outer diameter of 5-16 mm.
We do not recommend use for other applications.
Always use adaptor plates designed for the actual diameter of cable and duct.
It is very important to use the correct adaptor plates. If the adaptor plates do not fit the duct, dangerous
situations may occur. The machine comes in a carrying case. When the machine is not in use or during
transportation, always store it in the carrying case.
7. MOUNTING AND PREPARATIONS
Make sure to place the machine on a stable foundation and to fasten it with for example a bracket to withstand
the forces, which occur during use. The adaptor plates in the machine must fit the actual size of the fiber cable
and the microduct the cable is to be blown into.
The supply of fiber cable from a cable drum or similar must be set up in a way where the fiber cable is supplied
to the machine evenly and with the lowest force possible.
The microduct that the cable is blown into, should be without sharp corners or bends. Before blowing it is
recommended to blow a sponge through the duct. This ensures that the fiber cable can get all the way through
the duct without getting stuck.
Cleaning the duct
1. Apply one or multiple sponges in the duct.
2. Add air pressure and blow sponge.
3. Make sure the sponge arrives at the other end of
the duct.
4. Check that the sponge looks clean after it arrives
at the other end - or repeat with new sponges
until its clean.
Lubricating the duct
1. Remember to clean the duct prior to lubricating
it.
2. Apply one sponge at the desired depth (See
guideline on FlowLUB).
3. Add desired amount of FlowLUB
4. Apply one more sponge (creating three layers
with sponges and lubrication)
5. Add air pressure pushing sponges and FlowLUB all
the way through to the end.
NB: The machine is intended for indoor use and
not for use in wet environments, i.e. rainy weather.
If the machine is exposed to rain or humidity, it
can result in malfunction of the machine and lapse
of warranty.

Page | 11 of 40
FREMCO A/S
ELLEHAMMERVEJ 14 |DK9900 FREDERIKSHAVN, DENMARK |VAT NO.: DK30815416
TELEPHONE [phone] |[email protected] |WWW.FREMCO.DK
8. SUPPLY OF COMPRESSED AIR AND ELECTRICITY
It is very important that the quality and volume of compressed air for blowing is correct and meets
specifications. If there is water in the compressed air or too low pressure and volume of compressed air, it will
create insufficient results. The compressed air must be filtered, cooled and dried to avoid moisture and dirt in
the microduct.
MicroFlow TOUCH and MicroFlow LOG uses 24V DC and can be connected to 100-240V AC, 50/60 Hz with
the included transformer. The 100-240V AC power supply must be stable and at least 2A
9. FIBER PROTECTION TECHNOLOGY
MicroFlow TOUCH and MicroFlow LOG has a
unique protection technology securing that there is
no damage to the fiber cable. The protection
technology stops the machine if the fiber cable
meets an obstacle.
The stop occurs because the cable gets bent inside
the fiber blowing machine as the fiber cable meets
an obstacle. This is registered by a sensor, and the
motor stops immediately.
The machine will also stop automatically if the
motor exceeds the pre-set maximum torque level
(see section about Torque Off-Set for the
minimum effect needed depending on the speed).
In both cases of protection, the machine stops
immediately so the fiber cable does not get
damaged.
FAULT SEQUENCE
When the protection technology is activated, the machine starts the following fault sequence:
•The motor stops immediately.
•Short break.
•The machine pulls the fiber slightly backwards until the fiber is straight in the blowing junction block.
•The motor starts and accelerates to the preset maximum speed.
•If the protection technology is activated 3 times, the machine will come to a full stop, and an error
message is shown in the display.

Page | 12 of 40
FREMCO A/S
ELLEHAMMERVEJ 14 |DK9900 FREDERIKSHAVN, DENMARK |VAT NO.: DK30815416
TELEPHONE [phone] |[email protected] |WWW.FREMCO.DK
10. MicroFlow Touch Controller
If you have the MicroFlow Touch Controller as displayed below the following instructions apply.
If you have the MicroFlow Log Controller please proceed to paragraph 12. MicroFlow Log Controller.

Page | 13 of 40
FREMCO A/S
ELLEHAMMERVEJ 14 |DK9900 FREDERIKSHAVN, DENMARK |VAT NO.: DK30815416
TELEPHONE [phone] |[email protected] |WWW.FREMCO.DK
10.1.DISPLAY SYMBOLS
Start
Indicates machine is running
Book-service
Info: it is time to book an
authorized service check
Forward
Motor direction, press to
toggle between forward and
reverse
Set
Press to go to setup page
Reverse
Motor direction, press to
toggle between forward and
reverse
Setup
Press to set stop length.
Not active if value is “0”
Speedometer
Motor speed
Confirm
Press to confirm info and
return to main page
Torque
Motor torque
Torque
overload
Info when machine is
stopped by the torque
overload system
Meters
Actual values for length,
speed and torque
Fiber protection
Info when machine is
stopped by the fiber
protection system
Pre-set
Pre-set values for length,
speed and torque
Stop
Info when machine is
stopped, e.g. fiber or torque
stop
Ramps
Motor acceleration/
deceleration ramp functions
Reset
Resets meter counter
Home
Press to return to main
window
Login
Log in to a service info page
(login is required, and only
for service personnel)
Maintenance
Info: it is time for
maintenance
Close page
Press close service info and
return to main window

Page | 14 of 40
FREMCO A/S
ELLEHAMMERVEJ 14 |DK9900 FREDERIKSHAVN, DENMARK |VAT NO.: DK30815416
TELEPHONE [phone] |[email protected] |WWW.FREMCO.DK
10.2.RUNNING THE FIBER BLOWING MACHINE
•Prepare the fiber cable and place it inside the
fiber blowing machine. Adjust the drive wheels
until they are tight around the fiber cable
•Place the microduct, which the fiber cable is to
be blown into, in the blowing junction block
•Close the lid and tighten the screws on top
•On the TOUCH screen:
•Set the desired speed (m/min)
•Set the torque level to the desired
maximum
•OPTIONAL: The pre-set meter counter can
be used to stop the machine after a given
distance (set to “0” and the machine will
continue indefinitely)
•Press the ON/OFF button, and the machine will
accelerate to the pre-set maximum speed
After 10-20 meters, turn on air. Gradually increase
air supply as the blowing is proceeding.
•The blowing is now running automatically
•If the machine stops unintentionally, there are
two adjustable parameters:
•increase air supply
•or reduce speed if there is no more air
pressure
•Stop the machine, either manually or when
reaching the pre-set distance
•Turn off air
•The lid can be opened when the air pressure
gauge is at “0” bar/psi
WARNING: Do not open the
machine while under pressure, as this
may damage the machine and cause
personal injury.

Page | 15 of 40
FREMCO A/S
ELLEHAMMERVEJ 14 |DK9900 FREDERIKSHAVN, DENMARK |VAT NO.: DK30815416
TELEPHONE [phone] |[email protected] |WWW.FREMCO.DK
10.3.USE OF “TOUCH” CONTROL UNIT
The control unit is used for operating the fiber blowing machine as well as adjusting the different parameters, for
instance speed and torque level.
10.3.1. Adjustable Parameters
ADJUST
Torque Level
To avoid overload of the fiber cable, it is possible to adjust the maximum torque
level. If this maximum torque level is exceeded during blowing, the protection
technology stops the machine so that the fiber cable does not get damaged. The
torque level can be adjusted from 10 to 100% of the motor’s maximum effect.
ADJUST
Counter
Here you can choose a distance that the cable should be blown. When the pre-set
distance has been reached, the machine will stop automatically. If the counter is
set at “0”, the machine will continue indefinitely.
ADJUST
Speed
Here the speed of the machine can be adjusted in meter per minute.
ADJUST
Acceleration
Ramp
Adjusts the acceleration when the machine starts. It can be adjusted between 5
and 100, with 100 being the fastest acceleration. Recommend value: 5
ADJUST
Deceleration
Ramp
Adjusts the deceleration when the machine stops. It can be adjusted between 5
and 100, with 100 being the fastest deceleration. Recommend value: 100
TOUCH Display
Used to monitor and
adjust various parameters
ON/OFF Switch
Starts and stops the
machine

Page | 16 of 40
FREMCO A/S
ELLEHAMMERVEJ 14 |DK9900 FREDERIKSHAVN, DENMARK |VAT NO.: DK30815416
TELEPHONE [phone] |[email protected] |WWW.FREMCO.DK
10.4.TOUCH DISPLAY SCREEN OVERVIEW
Startup/Pause Window
Shown during startup, or when machine has been
inactive for some time.
Tab to activate main screen.
Main Window
This window is shown during machine operation. On
this screen it is possible to:
•Set and reset stop length, by pressing to set
length, and to reset (set to 0 disables the
length stop function)
•Increase/decrease both speed and torque, by
pressing .
•Access setup window,
•See machine status, running or
stopped
•Actual speed, torque and length
•Preset speed, torque and length
Setup Window
From this window it is possible to:
•Access motor ramp window
•Log in to a service info page (login is required,
and only for service personnel)
•Toggle motor direction
•Press to go back to main window

Page | 17 of 40
FREMCO A/S
ELLEHAMMERVEJ 14 |DK9900 FREDERIKSHAVN, DENMARK |VAT NO.: DK30815416
TELEPHONE [phone] |[email protected] |WWW.FREMCO.DK
Motor Ramp Setup
In this window the acceleration/deceleration
ramps during motor start/stop, can be
increased/decreased by pressing .
Press to go back to setup window
Press to go back to main window
Keypad
For entering length stop
Fiber Protection Warning
Popup window when fiber protection monitor is
activated.
Press to confirm and go to main window
Motor Torque Warning
Popup window when motor torque exceeds torque
setting.
Press to confirm and go to main window
100
5

Page | 18 of 40
FREMCO A/S
ELLEHAMMERVEJ 14 |DK9900 FREDERIKSHAVN, DENMARK |VAT NO.: DK30815416
TELEPHONE [phone] |[email protected] |WWW.FREMCO.DK
Fiber Protection and Motor Torque Warning
Popup window when a combination of fiber protection
and motor torque occur during automatic restart cycle.
Press to confirm and go to main window
Service Reminder
Info window shows during startup when it is time for a
service check of the machine.
Press to confirm and go to main window

Page | 19 of 40
FREMCO A/S
ELLEHAMMERVEJ 14 |DK9900 FREDERIKSHAVN, DENMARK |VAT NO.: DK30815416
TELEPHONE [phone] |[email protected] |WWW.FREMCO.DK
11. MICROFLOW LOG CONTROLLER
If you have the MicroFlow Log Controller as displayed below the following instructions apply.
If you have the MicroFlow Touch Controller please proceed to paragraph 11: MicroFlow Touch Controller.

Page | 20 of 40
FREMCO A/S
ELLEHAMMERVEJ 14 |DK9900 FREDERIKSHAVN, DENMARK |VAT NO.: DK30815416
TELEPHONE [phone] |[email protected] |WWW.FREMCO.DK
11.1.DISPLAY SYMBOLS
Get pdf
Press to get report as pdf
Submit
Submit content of page
Home
Press to return to the select
job type screen
Setup
Press to set stop length. Not
active if value is “0”
Logout
Log out of MicroFlow LOG
Complete
Press to confirm manual job
complete return select job type
screen
Select Wifi
Go to controller wifi selection
setup
Download
Report
Press to download report and
confirm job complete on a
report job
Delete user
Delete current user from
controller
Normal
Indicates that the machine runs
forward Press to reverse (only
available in manual mode)
Update
controller
Update software on
controller
Reverse
Indicates that the machine pulls
the fiber out of the duct. Press
to forward (only available in
manual mode)
Speedomet
er
Motor speed
Torque overload
Info when job has been
interrupted by a possible torque
issue
Torque
Motor torque
Fiber protection
Info when job has been
interrupted by a possible fiber
protection issue
Meters
Actual values for length, speed
and torque
Torque overload
Info when machine is stopped by
the torque overload system
Pre-set
Pre-set values for length,
speed and torque
Fiber protection
Info when machine is stopped by
the fiber protection system
Pressure
Air pressure
Stop
Info when machine is stopped,
e.g. fiber or torque stop
Ramps
Motor acceleration ramp
Shortcut to
reports folder
Press to gain access to pdf
reports already generated
Refresh
Refresh page
Shortcut to
MicroFlow LOG
Press to access MicroFlow LOG