Frigicoll WIFI USB 01 User manual

OWNER’S MANUAL
WiFi Controller
IMPORTANT NOTE:
Read the manual carefully before intalling or connecting
your Smart kit (Wireless module). Make sure to save this
manual for future reference.
WIFI USB 01

CONTENTS
1. SPECIFICATION ........................................................................................1
2. PRECAUTIONS ......................................................................................... 1
3. DOWNLOAD AND INSTALL APP .............................................................. 2
4. INSTALL THE SMART KIT ......................................................................... 3
5. USER REGISTRATION ............................................................................. 4
6. NETWORK CONFIGURATION ................................................................. 5
7. HOW TO USE APP .................................................................................. 12
8. SPECIAL FUNCTIONS ............................................................................ 14
DECLARATION OF CONFORMITY
Hereby, we declare that this Smart kit is in compliace with the essential
requirements and other relevant provisions of Directive 2014/53/EU.
A copy of the full DoC is attached. (European Union products only)

1
1. SPECIFICATION
Model WIFI USB 01
Standard IEEE 802.11 b/g/n
Antenna Type Printed PCB Antenna
Frequency WLAN 2400 ~ 2483.5 MHz
Maximum Transmitted Power 19.8 dBm Max..
Operation Temperature 0ºC~45ºC/32ºF~113ºF
Operation Humidity 10%~85%
Power Input DC 5 V/300 mA
2. PRECAUTIONS
• Applicable system: IOS, Android. (Suggest: IOS 8.0 or later, Android 4.0
or later)
Please keep you APP up to date with the latest version.
Due to special situation may be occurred, we explicitly claims below: Not
all of the Android and iOS system are compatible with APP. We will not
be responsible for any issue as a result of the incompatibility.
• Wireless safety strategy
Smart kit only support WPA-PSK/WPA2-PSK encryption and none
encryption. WPA-PSK/WPA2-PSK encryption is recommended.
CAUTION
• Due to different network situation, control process may return time-out
sometimes. If this situation occurs, the display between board and App
may not be the same, please do not feel confused.
• Smart Phone camera needs to be 5 million pixels or above to make sure
scan QR code well.
• Due to different network situation, sometimes, request time-out could
happen, thus, it is necessary to do network conguration again.
• The APP system is subjected to update without prior notice for product
function improvement. The actual network conguration process may be
slightly different from the manual, the actual process shall prevail.
• Please Check The Service Website For More Information.

2
3. DOWNLOAD AND INSTALL APP
Caution: The following QR Code is only available for downloading APP. It is
totally different with the QR code packed with SMART KIT.
Android iOS
• Android Phone users: scan Android QR code or go to Google Play,
search ‘NetHome Plus’ app and download it.
• iOS users: scan iOS QR code or go to APP Store, search ‘Nethome
Plus’ app and download it.

3
4. INSTALL THE SMART KIT (wireless module)
1 Remove the protective cap of the smart kit (wireless module)
2 Open the front panel and insert the smart kit (wireless module) into the
reserved interface.
3 Attach the QR code packed with Smart kit (wireless module) to the side
of the machine, ensure it is convenience to be scanned by the mobile
phone. Alternatively, user can take picture of the QR Code and save in
into their own phone.
WARNING: This interface is only compatible with SMART KIT (wireless
module) provided by the manufacturer.
Insert

4
5. USER REGISTRATION
• Please ensure your mobile device is connected to Wi router. Also,
the Wi router has already connected to Internet before doing user
registration and network conguration.
• It is better to log in your email box and active your registration account
by clicking link in case you forget the password.
1. Click “Sign up” 2. Enter your email address
and password, and then click
“Registration”,

5
6. NETWORK CONFIGURATION
CAUTIONS:
• It is necessary to forget any other around network and make sure
the Android or iOS device just connect to the Wireless network you
want to congure,
• Make sure the Android or iOS device Wireless function works
well and can be connected back to your original Wireless network
automatically.
Kindly reminder:
User must nish all the steps in 8 minutes after powering on air conditioner,
otherwise you need to power on it again
Using Android device to do network conguration:
1. Make sure your mobile device has already been connect to
the Wireless network which you want to use, Also, you need to
forget other irrelevant Wireless network in case it inuences your
conguration process.
2. Disconnect the power supply of air conditioner.
3. Connect the power supply of AC, and continuously press the “LED
DISPLAY” or “DO NOT DISTURB” button seven times in 10 seconds.
4. When the unit displays “AP”, it means that the air conditioner wireless
has already entered into “AP” Mode.
• Some type of air conditioner do not need the 2. step to be in AP.

6
5. Press “+ Add Device” 6. Select the appliance you
are setting upassword
and click “OK”.
7. Follow the above steps to enter “AP” mode

7
8. Choose the network
conguration
method
9. Choose the “Scan the
QR code” method
9. Or choose the “Manual
Setup” method
10. Please enter the
password

8
11. Network
conguration is
successful
12. Conguration Success,
you can see the device
on the list

9
Using iOS device to do network conguration:
1. Make sure your mobile device has already been connect to
the Wireless network which you want to use, Also, you need to
forget other irrelevant Wireless network in case it inuences your
conguration process.
2. Disconnect the power supply of AC (some units).
3. Connect the power supply of AC, and continuously press the “LED
DISPLAY” or “DO NOT DISTURB” button seven times in 10 seconds.
4. When the unit displays “AP”, it means that the air conditioner wireless
has already entered into “AP” Mode.
5. Press “+ Add Device” 6. Select the appliance you
are setting upassword and
click “OK”.

10
7. Follow the above steps to enter “AP” mode
8. Connect to the Wireless
network
9. Please enter password

11
10. Network conguration
is successful
11. Conguration Success,
you can see the device
on the list.
NOTE:
• When nishing network conguration, APP will display success cue
words on the screen.
• Due to different internet environment, it is possible that the device
status still display “ofine”. If this situation occurs, it is necessary to
pull and refresh the device list on the APP and make sure the device
status become “online”. Alternatively, user can turn off the AC power
and turn on it again, the device status will become “online” after few
minutes.

12
7. HOW TO USE APP
Please ensure both your mobile device and air conditioner are connected to
the Internet before using app to control the air conditioner via Internet, please
follow the next steps:
1. Click “Sign up” 2. Choose the air conditioner.
3. Thus, user can control air
conditioners on/off status,
operation mode, temperature, fan
speed and so on.
NOTE: Not all the function of the
APP is available on air conditioner.
For example: ECO, Turbo, Swing
function, please check the user
manual to nd more information.

13
8. SPECIAL FUNCTIONS
Including: Timer On, Timer Off, 8ºC Heat, Sleep, Check.
NOTE: If the air conditioner do not support the above function, the function will
be hided from the function list.
• Timer On / Timer Off
Weekly, user can make an appointment to turn on or off AC on specic time.
User also can choose circulation to keep the AC under schedule control every
week.
• 8ºC Heat
User can let the AC run under 8ºC Heat by one-click. When people go outside,
this function can protect your furniture from frost damage.

14
• Sleep
User can customize their own comfortable sleep by setting target temperature.
• Check
User can simply check the AC running status with this function. When nishing
this procedure, it can display the normal items, abnormal items, and detail
information.

15
• Share Device
The air conditioner can be controlled by multi-users at the same time by Share
Device function.
1. Click “Share device” 2. QR code display.
3. The other users must log in
‘Nethome Plus’ app rst, then
click “Add Share Device” on their
own mobile, then ask them to scan
the QR code.
4. Now the others can add the
shared device.

16
APP DECLARATION
FCC ID: 2AS2HMZNA19
IC : 24951-MZNA19
This debice complies with Part 15 of the FCC Rules and Industry Canada’s
licence-exempt RSSs.
Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may
cause undesired operation of the device
Only operate the device in accordance with the instructions supplied.
Changes or modications to this unit not expressly approced by the party
responsible for compliance could vois the user’s authority to operate the
equipment.
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the
FCC radio frequency exposure limits, human proximity to the antenna shall
not be less than 20cm (8 inches) during normal operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measure:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Company will not be liable for any issues and problems caused by
Internet, Wireless Router and Smart Devices. Please contact the
original provider to get further help.
CS374U-APP(OEM)
16110800000349
20190516