FRO­NIUS ActiveCharger 1000 Datasheet

/ Perfect Charging / Perfect Welding / Solar Energy
42,0426,0176,EN 021-05082016
AccuPocket 150/400
ActiveCharger 1000
Operating Instructions
Spare parts list
Rod electrode power source
EN

2

3
EN
Dear reader,
Introduction Thank you for the trust you have placed in our company and congratulations on buying this
high-quality Fronius product. These instructions will help you familiarise yourself with the
product. Reading the instructions carefully will enable you to learn about the many different
features it has to offer. This will allow you to make full use of its advantages.
Please also note the safety rules to ensure greater safety when using the product. Careful
handling of the product will repay you with years of safe and reliable operation. These are
essential prerequisites for excellent results.

4

5
EN
Contents
Safety rules 9
General ...................................................................................................................................................... 11
Explanation of safety symbols .............................................................................................................. 11
Operating environments........................................................................................................................ 11
Obligations of the operator.................................................................................................................... 11
Obligations of personnel ....................................................................................................................... 12
EMC Device Classifications.................................................................................................................. 12
Disposal ................................................................................................................................................ 12
Data protection...................................................................................................................................... 12
Copyright............................................................................................................................................... 12
Power source ............................................................................................................................................. 13
General ................................................................................................................................................. 13
Proper use ............................................................................................................................................ 13
Protecting yourself and others .............................................................................................................. 14
Noise emission values .......................................................................................................................... 14
Danger from toxic gases and vapours .................................................................................................. 15
Danger from flying sparks..................................................................................................................... 15
Dangers from welding current............................................................................................................... 15
Dangers from the battery ...................................................................................................................... 16
Meandering welding currents................................................................................................................ 17
EMC measures ..................................................................................................................................... 17
EMF measures...................................................................................................................................... 18
Factors affecting welding results........................................................................................................... 18
Danger from shielding gas cylinders..................................................................................................... 18
Safety precautions in the place of use and for storage and transport................................................... 19
Safety measures in normal operation ................................................................................................... 19
Safety inspection................................................................................................................................... 19
Commissioning, maintenance and repair.............................................................................................. 20
Safety symbols...................................................................................................................................... 20
Charger ...................................................................................................................................................... 21
General ................................................................................................................................................. 21
Proper use ............................................................................................................................................ 21
Mains connection.................................................................................................................................. 21
Dangers from mains current and charging current ............................................................................... 22
Protecting yourself and others .............................................................................................................. 22
Safety measures in normal operation ................................................................................................... 22
EMC measures ..................................................................................................................................... 23
Maintenance and repair ........................................................................................................................ 23
Warranty and liability............................................................................................................................. 23
Safety inspection................................................................................................................................... 23
Safety symbols...................................................................................................................................... 24
Power source 25
General ...................................................................................................................................................... 27
Device concept ..................................................................................................................................... 27
Warning notices on the device.............................................................................................................. 27
Application areas .................................................................................................................................. 28
Using rechargeable devices....................................................................................................................... 29
Safety.................................................................................................................................................... 29
Storage and transport ........................................................................................................................... 29
Service life of the battery ...................................................................................................................... 29
Battery protection functions ....................................................................................................................... 31
General ................................................................................................................................................. 31
Deep discharge protector...................................................................................................................... 31
Automatic switch-off.............................................................................................................................. 31
Temperature monitoring........................................................................................................................ 32
Overcharging protection........................................................................................................................ 32

6
Before commissioning................................................................................................................................ 33
Safety.................................................................................................................................................... 33
Proper use ............................................................................................................................................ 33
Setup regulations.................................................................................................................................. 33
Power connection ................................................................................................................................. 33
Before starting for the first time............................................................................................................. 34
Control elements and connections............................................................................................................. 35
Safety.................................................................................................................................................... 35
Connections and mechanical components ...........................................................................................35
Control panel......................................................................................................................................... 36
MMA welding ............................................................................................................................................. 38
Preparatory work................................................................................................................................... 38
MMA welding ........................................................................................................................................ 38
SoftStart / HotStart function .................................................................................................................. 38
Arc-force dynamic................................................................................................................................. 39
TIG welding................................................................................................................................................ 41
General ................................................................................................................................................. 41
Connecting the gas cylinder.................................................................................................................. 41
Preparatory work................................................................................................................................... 41
Setting the gas pressure....................................................................................................................... 42
TIG welding........................................................................................................................................... 42
TIG Comfort Stop.................................................................................................................................. 43
The Setup menu ........................................................................................................................................ 45
Accessing the Setup menu ................................................................................................................... 45
Changing welding parameters .............................................................................................................. 45
Exiting the Setup menu......................................................................................................................... 45
Parameters for MMA welding................................................................................................................ 45
Parameters for TIG welding.................................................................................................................. 46
VRD safety device (optional) ..................................................................................................................... 48
General ................................................................................................................................................. 48
Function ................................................................................................................................................ 48
Care, maintenance and disposal ............................................................................................................... 49
Safety.................................................................................................................................................... 49
General ................................................................................................................................................. 49
At every start-up.................................................................................................................................... 49
Every 2 months..................................................................................................................................... 50
Disposal ................................................................................................................................................ 50
Troubleshooting ......................................................................................................................................... 51
Safety.................................................................................................................................................... 51
Indicated errors..................................................................................................................................... 51
Service messages................................................................................................................................. 52
No function............................................................................................................................................ 53
Faulty operation .................................................................................................................................... 54
Technical data............................................................................................................................................ 56
Operating environments........................................................................................................................ 56
Explanation of the term "duty cycle" ..................................................................................................... 56
Technical data....................................................................................................................................... 57
Charger 59
General ...................................................................................................................................................... 61
Warning notices on the device.............................................................................................................. 61
Warning notices inside the device ........................................................................................................ 62
Proper use ............................................................................................................................................ 62
Before commissioning................................................................................................................................ 63
Mains connection.................................................................................................................................. 63
Generator-powered operation............................................................................................................... 63
Setup regulations.................................................................................................................................. 63
Space requirements.............................................................................................................................. 63
Control elements and connections............................................................................................................. 65
Safety.................................................................................................................................................... 65
Connections and components .............................................................................................................. 65
Control panel......................................................................................................................................... 65
Start-up ...................................................................................................................................................... 66

7
EN
Safety.................................................................................................................................................... 66
Commissioning ..................................................................................................................................... 66
Operating modes .................................................................................................................................. 67
Options....................................................................................................................................................... 68
Fitting the wall bracket .......................................................................................................................... 68
Troubleshooting ......................................................................................................................................... 69
Safety.................................................................................................................................................... 69
Indicated errors..................................................................................................................................... 69
No function............................................................................................................................................ 69
Technical data............................................................................................................................................ 70
Operating environments........................................................................................................................ 70
Technical data 230V ............................................................................................................................. 70
Standards 230V .................................................................................................................................... 71
Technical data 120V ............................................................................................................................. 71
Standards 120V .................................................................................................................................... 71
Technical data 100V ............................................................................................................................. 71
Standards 100V .................................................................................................................................... 72
Appendix 73
Spare parts list: AccuPocket ...................................................................................................................... 74
Spare parts list: ActiveCharger .................................................................................................................. 75

8

Safety rules

11
EN
General
Explanation of
safety symbols
If you see any of the symbols depicted in the "Safety rules" chapter, special care is re-
quired.
Operating envi-
ronments
Obligations of the
operator
DANGER! Indicates immediate and real danger. If it is not avoided, death or se-
rious injury will result.
WARNING! Indicates a potentially dangerous situation. Death or serious injury
may result if appropriate precautions are not taken.
CAUTION! Indicates a situation where damage or injury could occur. If it is not
avoided, minor injury and/or damage to property may result.
NOTE! Indicates a risk of flawed results and possible damage to the equipment.
IMPORTANT! Indicates tips for correct operation and other particularly useful information.
It does not indicate a potentially damaging or dangerous situation.
Transport, storage or operation of the charger outside the stipulated area will
be deemed improper. The manufacturer shall not be held liable for any dam-
age arising from such usage.
Ambient temperature range:
- during operation: -10 °C to +40 °C (14 °F to 104 °F)
- during transport and storage: -20 °C to +55 °C (-4 °F to 131 °F)
- recommended temperature range during charging: + 4 °C to + 40 °C (+
39,2 °F to + 104 °F)
Relative humidity:
- up to 50 % at 40 °C (104 °F)
- up to 90 % at 20 °C (68 °F)
The surrounding air must be free from dust, acids, corrosive gases or sub-
stances, etc.
Can be used at altitudes up to 2000 m (6561 ft.)
The operator must only allow persons to work with the device who:
- are familiar with the fundamental instructions regarding safety at work and
accident prevention and have been instructed in how to use the device
- have read and understood these operating instructions, especially the
section "safety rules", and have confirmed as much with their signatures
- are trained to produce the required results.
Checks must be carried out at regular intervals to ensure that operators are
working in a safety-conscious manner.

12
Obligations of
personnel
EMC Device Clas-
sifications
Disposal
Data protection
Copyright
Before using the device, all persons instructed to do so undertake:
- to observe the basic instructions regarding safety at work and accident
prevention
- to read these operating instructions, especially the "Safety rules" section
and sign to confirm that they have understood them and will follow them.
Before leaving the workplace, ensure that people or property cannot come to
any harm in your absence.
Devices in emission class A:
- Are only designed for use in industrial settings
- Can cause line-bound and radiated interference in other areas
Devices in emission class B:
- Satisfy the emissions criteria for residential and industrial areas.
This is also true for residential areas in which the energy is sup-
plied from the public low-voltage mains.
EMC device classification as per the rating plate or technical data.
Do not dispose of this device with normal domestic waste! To comply with the
European Directive on Waste Electrical and Electronic Equipment and its im-
plementation as national law, electrical equipment that has reached the end of
its life must be collected separately and returned to an approved recycling fa-
cility. Any device that you no longer require must either be returned to your
dealer or given to one of the approved collection and recycling facilities in your
area. Ignoring this European Directive may have potentially adverse affects on
the environment and your health!
The user is responsible for the safekeeping of any changes made to the fac-
tory settings. The manufacturer accepts no liability for any deleted personal
settings.
Copyright of these operating instructions remains with the manufacturer.
The text and illustrations are all technically correct at the time of printing. We
reserve the right to make changes. The contents of the operating instructions
shall not provide the basis for any claims whatsoever on the part of the pur-
chaser. If you have any suggestions for improvement, or can point out any
mistakes that you have found in the instructions, we will be most grateful for
your comments.

13
EN
Power source
General
Proper use
The device is manufactured using state-of-the-art technology and according
to recognised safety standards. If used incorrectly or misused, however, it can
cause:
- injury or death to the operator or a third party,
- damage to the device and other material assets belonging to the operat-
ing company,
- inefficient operation of the device.
All persons involved in commissioning, operating, maintaining and servicing
the device must:
- be suitably qualified,
- have sufficient knowledge of welding and
- read and follow these operating instructions carefully.
The operating instructions must always be at hand wherever the device is be-
ing used. In addition to the operating instructions, attention must also be paid
to any generally applicable and local regulations regarding accident preven-
tion and environmental protection.
All safety and danger notices on the device
- must be in a legible state,
- must not be damaged,
- must not be removed,
- must not be covered, pasted or painted over.
For the location of the safety and danger notices on the device, refer to the
section headed "General" in the operating instructions for the device.
Before switching on the device, rectify any faults that could compromise safe-
ty.
This is for your personal safety!
The device is to be used exclusively for its intended purpose.
The device is intended solely for the welding processes specified on the rating
plate.
Any use above and beyond this purpose is deemed improper. The manufac-
turer shall not be held liable for any damage arising from such usage.
Proper use includes:
- carefully reading and following all the instructions given in the operating
instructions
- studying and obeying all safety and danger notices carefully
- performing all stipulated inspection and maintenance work.
Never use the device for the following purposes:
- Thawing out pipes
- Charging batteries
- Starting engines
The device is designed for use in industry and the workshop. The manufactur-
er accepts no responsibility for any damage caused through use in a domestic
setting.
The manufacturer likewise accepts no liability for inadequate or incorrect re-
sults.

14
Protecting your-
self and others
Noise emission
values
Persons involved with welding expose themselves to numerous risks, e.g.:
- flying sparks and hot pieces of metal
- arc radiation, which can damage eyes and skin
- hazardous electromagnetic fields, which can endanger the lives of those
using cardiac pacemakers
- risk of electrocution from mains current and welding current
- greater noise pollution
- harmful welding fumes and gases
Anyone working on the workpiece while welding is in progress must wear suit-
able protective clothing with the following properties:
- flame-resistant
- insulating and dry
- covers the whole body, is undamaged and in good condition
- safety helmet
- trousers with no turn-ups
Protective clothing refers to a variety of different items. Operators should:
- protect eyes and face from UV rays, heat and sparks using a protective
visor and regulation filter.
- wear regulation protective goggles with side protection behind the protec-
tive visor.
- wear stout footwear that provides insulation even in wet conditions.
- protect the hands with suitable gloves (electrically insulated and providing
protection against heat).
- wear ear protection to reduce the harmful effects of noise and to prevent
injury.
Keep all persons, especially children, out of the working area while any devic-
es are in operation or welding is in progress. If, however, there are people in
the vicinity,
- make them aware of all the dangers (risk of dazzling by the arc, injury
from flying sparks, harmful welding fumes, noise, possible risks from
mains current and welding current, etc.),
- provide suitable protective equipment or
- erect suitable safety screens/curtains.
The device generates a maximum sound power level of <80 dB(A) (ref. 1pW)
when idling and in the cooling phase following operation at the maximum per-
missible operating point under maximum rated load conditions according to
EN 60974-1.
It is not possible to provide a workplace-related emission value during welding
(or cutting) as this is influenced by both the process and the environment. All
manner of different welding parameters come into play, including the welding
process (MIG/MAG, TIG welding), the type of power selected (DC or AC), the
power range, the type of weld metal, the resonance characteristics of the
workpiece, the workplace environment, etc.

15
EN
Danger from toxic
gases and va-
pours
Danger from fly-
ing sparks
Dangers from
welding current
The fumes produced during welding contain harmful gases and vapours.
Welding fumes contain substances that may, under certain circumstances,
cause birth defects or cancer.
Keep your face away from welding fumes and gases.
Fumes and hazardous gases
- must not be breathed in
- must be extracted from the working area using appropriate methods.
Ensure an adequate supply of fresh air.
Otherwise, a protective mask with an air supply must be worn.
Close the shielding gas cylinder valve or main gas supply if no welding is tak-
ing place.
If there is any doubt about whether the extraction system is powerful enough,
then the measured toxic emission values should be compared with the permis-
sible limit values.
The following components are responsible, amongst other things, for the de-
gree of toxicity of welding fumes:
- Metals used for the workpiece
- Electrodes
- Coatings
- Cleaners, degreasers, etc.
The relevant material safety data sheets and manufacturer's specifications for
the listed components should therefore be studied carefully.
Flammable vapours (e.g. solvent fumes) should be kept away from the arc's
radiation area.
Flying sparks may cause fires or explosions.
Never weld close to flammable materials.
Flammable materials must be at least 11 metres (36 ft. 1.07 in.) away from the
arc, or alternatively covered with an approved cover.
A suitable, tested fire extinguisher must be available and ready for use.
Sparks and pieces of hot metal may also get into adjacent areas through small
gaps or openings. Take appropriate precautions to prevent any danger of in-
jury or fire.
Welding must not be performed in areas that are subject to fire or explosion or
near sealed tanks, vessels or pipes unless these have been prepared in ac-
cordance with the relevant national and international standards.
Do not carry out welding on containers that are being or have been used to
store gases, propellants, mineral oils or similar products. Residues pose an
explosive hazard.
An electric shock is potentially life threatening and can be fatal.
Do not touch live parts either inside or outside the device.

16
Dangers from the
battery
Make sure that you and others are protected with an adequately insulated, dry
temporary backing or cover for the earth or ground potential. This temporary
backing or cover must extend over the entire area between the body and the
earth or ground potential.
All cables and leads must be secured, undamaged, insulated and adequately
dimensioned. Loose connections, scorched, damaged or inadequately dimen-
sioned cables and leads must be replaced immediately.
Do not sling cables or leads around the body or parts of the body.
The electrode (rod electrode, tungsten electrode, welding wire, etc.) must
- never be immersed in liquid for cooling
- never be touched when the power source is switched on.
Double the open circuit voltage of a power source can occur between the
welding electrodes of two power sources. Touching the potentials of both elec-
trodes at the same time may be fatal under certain circumstances.
If necessary, provide an adequate earthing connection for the workpiece.
Switch off unused devices.
The substances contained in the battery used in this device can be harmful to
the environment and to human and animal health.
If the device becomes damaged, please observe the following points:
- Make sure that leaking fluids cannot get into the soil or groundwater
- If pollution has already occurred, it must be removed in accordance with
relevant national regulations
The battery can catch fire if overheated. Do not expose the device to heat
(e.g. a permanent heat source or fire)
If the battery is damaged or subjected to improper use, dangerous vapours
may be given off which can irritate the airways.
If this happens:
- Ensure an adequate supply of fresh air
- Seek medical attention in case of discomfort
With a faulty battery, liquid may leak out of the device.
- Avoid contact with the liquid
- Hand the device over to a Fronius Service Partner for repair
- Clean and check any parts that have come into contact with the liquid
Do not operate or store the device in a potentially explosive atmosphere.
Special regulations apply in rooms at risk of fire or explosion.
Observe relevant national and international regulations.

17
EN
Meandering weld-
ing currents
EMC measures
To comply with European Directive 2006/66/EC on Batteries and Accumula-
tors and its implementation in national law, batteries and rechargeable batter-
ies that have reached the end of their life must be collected separately and
returned to an approved recycling facility. Be sure to return any device that you
no longer require to your dealer, or find out about the approved collection and
recycling facilities in your area. Ignoring this European Directive may be harm-
ful to the environment and your own health!
Devices with mechanically undamaged rechargeable batteries may be re-
turned to the relevant Fronius Service Partner for repair or battery replace-
ment.
As soon as it becomes evident that the rechargeable battery has been me-
chanically damaged (e.g. electrolyte is escaping), dispose of the device at
your nearest recycling centre in accordance with national laws and guidelines.
If anything is unclear or you have any questions about disposal, contact your
Fronius Service Partner.
If the following instructions are ignored, meandering welding currents can de-
velop with the following consequences:
- Fire hazard
- Overheating of parts connected to the workpiece
- Irreparable damage to ground conductors
- Damage to device and other electrical equipment
Ensure that the workpiece is held securely by the workpiece clamp.
Attach the workpiece clamp as close as possible to the area that is to be weld-
ed.
If the floor is electrically conductive, the device must be set up with sufficient
insulating material to insulate it from the floor.
If distribution boards, twin-head mounts, etc., are being used, note the follow-
ing: The electrode of the welding torch / electrode holder that is not used is
also live. Make sure that the welding torch / electrode holder that is not used
is kept sufficiently insulated.
In certain cases, even though a device complies with the standard limit values
for emissions, it may affect the application area for which it was designed (e.g.
when there is sensitive equipment at the same location, or if the site where the
device is installed is close to either radio or television receivers).
If this is the case, then the operator is obliged to take appropriate action to rec-
tify the situation.
Check and evaluate the immunity to interference of nearby devices according
to national and international regulations. Examples of equipment that may be
susceptible to interference from the device include:
- Safety devices
- Power, signal and data transfer lines
- IT and telecommunications devices
- Measuring and calibrating devices
Supporting measures for avoidance of EMC problems:
1. Mains supply
- If electromagnetic interference arises despite correct mains connec-
tion, additional measures are necessary (e.g. use a suitable line fil-
ter).

18
EMF measures
Factors affecting
welding results
Danger from
shielding gas cyl-
inders
2. Welding power leads
- must be kept as short as possible
- must run close together (to avoid EMF problems)
- must be kept well apart from other leads
3. Equipotential bonding
4. Earthing of the workpiece
- If necessary, establish an earth connection using suitable capacitors.
5. Shielding, if necessary
- Shield off other nearby devices
- Shield off entire welding installation
Electromagnetic fields may pose as yet unknown risks to health:
- effects on the health of others in the vicinity, e.g. wearers of pacemakers
and hearing aids
- wearers of pacemakers must seek advice from their doctor before ap-
proaching the device or any welding that is in progress
- for safety reasons, keep distances between the welding cables and the
welder's head/torso as large as possible
- do not carry welding cables and hosepacks over the shoulders or wind
them around any part of the body
The following requirements with regard to shielding gas quality must be met if
the welding system is to operate in a correct and safe manner:
- Size of solid matter particles < 40 μm
- Pressure dew point < -20 °C
- Max. oil content < 25 mg/m³
Filters must be used if necessary.
NOTE! There is an increased risk of soiling if ring mains are being
used
Shielding gas cylinders contain gas under pressure and can explode if dam-
aged. As the shielding gas cylinders are part of the welding equipment, they
must be handled with the greatest of care.
Protect shielding gas cylinders containing compressed gas from excessive
heat, mechanical impact, slag, naked flames, sparks and arcs.
Mount the shielding gas cylinders vertically and secure according to instruc-
tions to prevent them falling over.
Keep the shielding gas cylinders well away from any welding or other electrical
circuits.
Never hang a welding torch on a shielding gas cylinder.
Never touch a shielding gas cylinder with an electrode.
Risk of explosion - never attempt to weld a pressurised shielding gas cylinder.
Only use shielding gas cylinders suitable for the application in hand, along with
the correct and appropriate accessories (regulator, hoses and fittings). Only
use shielding gas cylinders and accessories that are in good condition.
Turn your face to one side when opening the valve of a shielding gas cylinder.
Close the shielding gas cylinder valve if no welding is taking place.

19
EN
Safety precau-
tions in the place
of use and for
storage and
transport
Safety measures
in normal opera-
tion
Safety inspection
If the shielding gas cylinder is not connected, leave the valve cap in place on
the cylinder.
The manufacturer's instructions must be observed as well as applicable na-
tional and international regulations for shielding gas cylinders and accesso-
ries.
A toppling device can cause life-threatening injuries. Place the device on a sol-
id, level surface so that it remains stable
- The maximum permissible tilt angle is 10°.
Do not operate or store the device in a potentially explosive atmosphere.
Special regulations apply in rooms at risk of fire or explosion.
Observe relevant national and international regulations.
Use internal directives and checks to ensure that the workplace environment
is always clean and clearly laid out.
Only set up and operate the device in accordance with the degree of protec-
tion shown on the rating plate.
When setting up the device, ensure there is an all-round clearance of 0.5 m (1
ft. 7.69 in.) to ensure that cooling air can flow in and out freely.
When transporting the device, observe the relevant national and local guide-
lines and accident prevention regulations. This applies especially to guidelines
regarding the risks arising during transport.
After transporting the device, it must be visually inspected for damage before
commissioning. Any damage must be repaired by trained service technicians
before commissioning the device.
Odourless and colourless shielding gas may escape unnoticed if an adapter
is used for the shielding gas connection. Prior to assembly, seal the device-
side thread of the adapter for the shielding gas connection using suitable Tef-
lon tape.
Only operate the device if all safety devices are fully functional. If the safety
devices are not fully functional, there is a risk of
- injury or death to the operator or a third party,
- damage to the device and other material assets belonging to the operator,
- inefficient operation of the device.
Any safety devices that are not functioning properly must be repaired before
switching on the device.
Never bypass or disable safety devices.
Before switching on the device, ensure that no one is likely to be endangered.
Check the device at least once a week for obvious damage and proper func-
tioning of safety devices.
The manufacturer recommends that a safety inspection of the device is per-
formed at least once every 12 months.
The manufacturer recommends that the power source be calibrated during the
same 12-month period.

20
Commissioning,
maintenance and
repair
Safety symbols
A safety inspection should be carried out by a qualified electrician
- after any changes are made
- after any additional parts are installed, or after any conversions
- after repair, care and maintenance has been carried out
- at least every twelve months.
For safety inspections, follow the appropriate national and international stand-
ards and directives.
Further details on safety inspection and calibration can be obtained from your
service centre. They will provide you on request with any documents you may
require.
It is impossible to guarantee that bought-in parts are designed and manufac-
tured to meet the demands made of them, or that they satisfy safety require-
ments.
- Use only original spare and wearing parts (also applies to standard parts).
- Do not carry out any modifications, alterations, etc. to the device without
the manufacturer's consent.
- Components that are not in perfect condition must be replaced immedi-
ately.
- When ordering, please give the exact designation and part number as
shown in the spare parts list, as well as the serial number of your device.
The housing screws provide the ground conductor connection for earthing the
housing parts.
Only use original housing screws in the correct number and tightened to the
specified torque.
Devices with the CE mark satisfy the essential requirements of the low-voltage
and electromagnetic compatibility directive (e.g. relevant product standards
from the EN 60 974 series).
Fronius International GmbH declares that the device complies with directive
2014/53/EU. The full text of the EU Declaration of Conformity is available from
the following website: http://www.fronius.com
Devices with the CSA test mark satisfy the requirements of the relevant stand-
ards in Canada and the USA.