Front Runner LADD017 User manual

LADD017_REV_A00 © 2021 FRONT RUNNER VEHICLE OUTFITTERS
front runner
LADD017
ENG
1
Thank you for purchasing a Front Runner Rack Ladder.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the included components.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.
Rack Ladder

LADD017_REV_A00 © 2021 FRONT RUNNER VEHICLE OUTFITTERS 2
TOOLS NEEDED
FIGURE 1.1
CHECK ONLINE FOR THE LATEST FITMENT GUIDE WWW.FRONTRUNNEROUTFITTERS.COM
GET ORGANIZED
1
IN THE BOX
5
7
6
8
3
1
4
10mm
4mm
1 2 X Ladder Sides - Bottom Assembly
2 2 X Ladder Sides - Top
3 6 X Ladder Rung - 341.5mm Long
4 4 X Ladder Feet
5 4 X M6 x 20 Button Head Bolt
6 4 X M6 Nut Cap
7 4 X M6 Nyloc Nut
8 12 X M6 x 25 Flange Button Head Torx
Torx
T30
2

LADD017_REV_A00 © 2021 FRONT RUNNER VEHICLE OUTFITTERS
3
FIT AND SECURE2
2.1
2.2
2.3
Assemble the Ladder Feet (Item4) to the
ends of the Ladder Side Top and Bottom
(Items 1 & 2) using M6 x 20 Button Head
Bolts and M6 Nyloc Nuts (Items 5 & 7).
Place M6 Nut Caps (Item 6) on all the Nyloc
Nuts.
Assemble 3 Ladder Rungs (Item 3) to the
Ladder Top and Bottom Sides (Item 1 &
2) using M6 x 25 Flange Button Head Torx
thread forming screws. (Item 8).
Before use, slide the Ladder top assembly
into the bottom assembly as shown.
5
7
6
4
1 2
3
2
8
Use a little oil on screw threads before
inserting. Note these are Thread
Forming Screws.
Tightening Torque 8-10Nm /
5.9 ft lb - 7.38 ft lb. Take care when
using a cordless driver.
MAKE SURE LADDER IS ON A STABLE
AND NON SLIP SURFACE WHEN USING.

LADD017_REV _A00 © 2021 FRONT RUNNER VEHICLE OUTFITTERS 4
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
4
Now's the time to visit your favorite Front Runner Dealer in person or online.
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
FINISH
3
Congratulations! You did it. Take a step back and admire your work!