Frontgate Holiday 151883 CLE User manual

CRYSTAL TREE 3FT POTTED- CLEAR - ITEM# 151883 CLE

Bottom Section A
Step 2
Plug light set from section A into wall outlet.
Step 1
Insert the section A of the tree into the pot.
Step 3
To shape your tree, start with the bottom most layer of
branches, with each branch start with the tips closest to
the pole and lift each tip up and out in alternating
directions. Repeat for each branch.
Step 4
To shape the top of the tree it will be necessary to
gently bend the branches downward to the desired
angle before shaping the tips.
SKU 151883 CLE - CRYSTAL TREE 3ft POTTED - CLEAR
176 TIPS
UL 100 REMAIN-ON LIGHTS
MAX DIAMETER 23”
NUMBER OF PERSONS
RECOMMENDED FOR
ASSEMBLY: 1
PARTS LIST
A. BOTTOM
HARDWARE
A. POT
B. EXTRA BULBS AND FUSES
QUANTITY: 1 PC
QUANTITY: EACH 4 PCS
CRYSTAL TREE 3FT POTTED- CLEAR - ITEM# 151883 CLE
ASSEMBLY INSTRUCTIONS

!
Step 1
Unplug the light set from wall outlet
Step 2
Remove section A from Pot and hold upside down and
branches will fold toward the pole. It is recommended to
snugly bind branches to the pole with a length of rope or
twine. This will allow for easy handling and storage.
Step 3
Place tree section, and pot in original box and tape
shut. Store tree in cool dry area, storage area
temperature should not exceed 100ºF.
STORAGE TIPS
CARE & MAINTENANCE INSTRUCTION
1. This is for decorative use only - do not immerse in water or expose to heat. Keep away from fire.
2. Please use water only for cleaning purpose.
3. When not in use, store neatly in a cool, dry location protected from sun light
1. Light tree one section at a time as described in assembly instructions, so you can easily identify and
bulbs that may be dislodged. Push any loose bulbs back into their sockets.
2. Separate the branch tips to form a “V” shape and fluff the needles. Make sure each tip is spread out
and no two branches are touching each other. For best access to branches, shape each section prior to
adding the next section as described in the initial assembly instructions. You may want to wear
cotton gloves when fluffing needles to avoid scratches and skin irritation.
3. Starting with the bottom row, position the branches parallel to the floor. Angle the tips slightly
upward like they are growing towards the sun. With each successive row, make the upward angle of
the branches more pronounced. Position inner tips to hide the center of the tree.
4. Arrange the uppermost section of the tree so that the tips are evenly spaced and pointing upward.
5. Step back and review the tree. Adjust branches and tips as necessary to give the tree a fuller
appearance (The tree may be shaped differently (upswept/downswept/ etc.) pending on one’s
preference.)
THE FOLLOWING STEPS WILL HELP MAKE YOUR TREE LOOK MORE REALISTIC
1. If entire tree lighting does not light, make sure the light sets are securely inserted in a working wall
outlet.
2. If an entire section of the tree does not light, please review following actions:
TROUBLE SHOOTING TIPS
a) Check that all plugs within the tree are securely connected.
b) Check the fuse in light sets to determine if it may need replacement. Caution: Noted that a
blown fuse indicates an electrical overload or electrical short circuit. If the fuse is blown,
unplug light sets from outlet. Also, unplug any additional strings. Replace the fuse following
manufacturer instruction with proper fuse rating. If the replacement fuse blows, a short circuit
may be present and the product should be discarded.
c) Check fuse in plug connection on end of each light string (See section on replacing plug fuses
in this document).

3. If some individual lights do not light up, it may be due to becoming dislodged from the socket during
assembly. Note those not lit up; check for looseness and push any loose bulbs gently back into their
socket. If they still do not light up, try a replacement light bulb (supplied by manufacturer) and
follow directions in section describing how to replace light bulbs.
TROUBLE SHOOTING TIPS (Cont.)
When using electrical products, to avoid risk of fire burns, personal injury and electrical shock, basic
precautions should always be followed as stated below:
TROUBLE SHOOTING TIPS (Cont.)
RED AND FOLLOW ALL SAFETY INSTRUCTIONS
1. Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When
products are used in outdoor applications, connect the product to a Ground Fault Circuit
interrupting (CFCI) outlet. If one is not provided, contact a qualified electrician for proper
installation.
2. This seasonal use product is not intended for permanent installation or use.
3 Do not mount or place near gas or electrical heaters, fireplace, candles or other similar sources of
heat.
4. Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
5. Do not let lamps rest on the supply cord or on any wire.
6. For your safety, unplug the product when leaving the house, when retiring for the night or if left
unattended.
7. This is an electrical product - not a toy! To avoid risk of fire, burns, personal injury and electric
shock it should not be played with or placed where small children can reach it.
8. Do not use this product for other than its intended use.
9. Do not hang ornaments or other objects from cord, wire or light string.
10. Do not close doors or windows on the product or extensions cords as this may damage the wire
insulation.
11. Do not cover the product with cloth, paper or any material not part of the product when in use.
12. This product is equipped wit push-in lamps. Do not twist the lamps.
13. This product employs overload protection (fuse). A blown fuse indicates an overload or
short-circuit situation. If the fuse blows, unplug the product from the outlet. Also, unplug any
additional strings or products that may be attached to the product. Replace the fuse as per the user
servicing instructions (follow product marking for proper fuse rating) and check the product. If
the replacement fuse blows a short-circuit may be present and the product should be discarded.
14. Read and follow all instructions that are on the product or provided with the product.

OPEN
OPEN
TO REPLACE A FUSE
CAUTION: FIRST UNPLUG YOUR PRODUCT FROM ANY POWER SOURCE.
TO REPLACE LIGHT BULBS
CAUTION: FIRST UNPLUG YOUR PRODUCT FROM ANY POWER SOURCE.
1. To reduce the risk of overheating, replace burned-out light bulbs promptly. Use only
2.5 volt light bulbs only.
2. Grasp plug and remove from the receptacle or any other electrical outlet device. Do
not unplug by pulling on the cord.
3. Pull the light bulb and its attached plastic base straight out of light bulb holder
4. Replace light bulb with only 2.5 volt super bright type light (provided with product).
5. If the new lamp base does not fit the replacement light bulb, follow the steps below
before step 4
A. Remove the base of burned out light by straightening light leads and gently pull
bulb out.
B. Thread metal leads of new lamp through hose in old base with one lead in each
hold.
C. After lamp is fully inserted into base, bend each lead up, like other lights in the
light set so that the leads will touch the contacts inside the light socket.
1. Grasp plug and remove from the receptacle or other outlet device. Do not unplug
by pulling on cord.
2. Open fuse cover. Slide open fuse access cover on top of attachment plug towards
plug’s metal prongs or blades
3. Remove fuse carefully (do not apply pressure to the glass part of fuse when
removing or replacing.)
4. Risk of fire. Replace fuse ONLY with 3 Amp 120 Volt fuse. (Provided with product).
5. Close fuse cover. Return the sliding fuse cover back to its former closed position on
attachment plug.
6. Risk of fire. Do not replace attachment plug because it contains a safety device (fuse)
that should not be removed. Discard product if the attachment plug is damaged.
Please contact one of our Product Specialists for assembly assistance or questions at 1-800-537-8484 or email [email protected]
Specialists are available weekdays 8:00 a.m. to 8:00 p.m. EST or Saturday 9:30 a.m. to 6:00 p.m.
USER INSTRUCTIONS
FUSE OVER
SLIDES FORWARD
3 AMP
120 VOLT
FUSES
PUSH BULB DOWN
TO REPLACE
PULL BULB UP
TO REMOVE
E305737
MODEL NO.: YXOULA 100L/2F
MODEL NO.: YXOULA 50L/1F