Frontgate Royal Spruce Pro Shape Tree User manual

61246 / 7.5 ft. Royal Spruce Pro Shape Tree Page 1
F R O N T G A T E®
F R O N T G A T E®F R O N T G A T E®
F R O N T G A T E®
OUTFITTING AMERICA’S FINEST HOMES®
INSTRUCTIONS FOR:
Item# 61246 CLR/ 7.5 t. Royal Spruce Pro Shape Tree with 1200 ct. Clear Lights
Item# 61246 MUL/ 7.5 t. Royal Spruce Pro Shape Tree with 1200 ct. Multi Lights
BILL OF MATERIAL (BO
M
)
PACKED IN ONE REUSABLE CARTON
•1 EA. TREE STAND (with 3 screws)
•1 EA. BOTTOM SECTION OF TREE “A”
•1 EA. LOWER MIDDLE SECTION OF TREE “B”
•1 EA. UPPER MIDDLE SECTION OF TREE “C”
•1 EA. TREE TOP SECTION OF TREE “D”
•1 EA. REMOTE ON AND OFF UNIT
•1 EA. WARRANTY AND INSTRUCTIONS
•1 EA PACKET OF EXTRA BULBS AND FUSES
•1 EA. TREE CARTON-WITH EXPANDABLE FEATURE
•1 PAIR ARTIFICIAL CHRISTMAS TREE SHAPING GLOVES
TREE ASSEMBLY INSRUCTIONS
1. Unpack:
Carefully remove the contents from the carton and keep the carton for future storage. Some
sections of the tree may be heavy and assistance may be required. Be sure to untangle any
wires that may be caught with other items. (Please D N T forcibly remove any contents.)
Remove any outer foam wrapping from the tree and its branches (See Fig. 1A).
Fig. 1A
2. Basic Assembly Steps:
CAUTION: Two people may be needed to balance and assemble tree’s upper
sections. Please use a ladder, i needed, and ollow all ladder sa ety instructions.
2.1 - pen the carton and take out all the contents. All contents that are listed in the Bill of
Material section on this page should be enclosed. Locate the tree stand and assemble it by
separating the legs of the stand to form an “X” shape (See Fig. 2A). Insert each of the three

61246 / 7.5 ft. Royal Spruce Pro Shape Tree Page 2
screws into the holes on the stand’s middle section, being sure that screws do not extend so far
as to interfere with installation of the tree pole. Place tree stand in desired location.
Fig. 2A
2.2 - Locate Tree Section “A” and remove the protective caps that are on the top and
bottom of the pole (they can be replaced when you re-pack your tree). Insert Tree Section
“A” into the tree stand (See Fig. 2B). Make sure the pole is firmly inserted into the stand, and
then turn all three screws until contact is made with the pole. If Section “A” is not sitting
straight, then simply loosen the screws, adjust tree pole, and retighten the screws.
Fig. 2B
All the branches are connected to the tree’s center pole by metal hinges
(See Figure 2). Remove the packing strap that is around the tree section
and allow the branches to fall into place. As this is a FRONTGATE
Pro Shape Tree, the leaves will spring into their correct position,
ONLY MINIMAL SHAPING IS NECESSARY!!!

61246 / 7.5 ft. Royal Spruce Pro Shape Tree Page 3
2.3 - Locate Tree Section “B” and insert into the top of Tree Section “A”. Make sure
section “B” is seated securely into the top of section “A” (See Fig. 2C). Remove the packing
strap that is wrapped around this tree section, same as you for Section “A”. Allow the
branches and leaves to fall into place.
Fig. 2C
2.4 - Locate Tree Section “C” and insert into the top of the Tree Section “B”. Make sure
section “C” is seated securely into the top of section “B” (See Fig. 2D). Remove the packing
strap that is wrapped around this tree section, same as did you for Section “B”. Allow the
branches and leaves to fall into place.
Fig. 2D

61246 / 7.5 ft. Royal Spruce Pro Shape Tree Page 4
2.5 - Locate Tree Section “D” and insert into the top of the Tree Section “C”. Make sure
section “D” is seated securely into the top of section “C” (See Fig. 2E). Remove the packing
strap that is wrapped around this tree section, same as did you for Section “B”. Allow the
branches and leaves to fall into place.
Fig. 2E

61246 / 7.5 ft. Royal Spruce Pro Shape Tree Page 5
3. Light Set and Power Connection:
3.1 – In the tree carton, there is a brown box that contains your n/ ff Remote Kit. Plug
your n/ ff Remote Control Unit (See Fig. 3A) into the closest electrical outlet near the tree
(See Fig. 3B). Plug the extension cords into the n/ ff Remote Control Unit. The Unit
comes with one Remote Control.
Fig. 3A Fig. 3B
3.2 – Your tree is lighted with miniature lights that are strung on the tree at the factory.
Those lights are plugged into the extension cords on the tree.
Your 7.5 t. tree will have One (1) extension cord plug. Total Light Set plugs equal
thirteen (13).
Sections “A”, “B”, “C”, and
“D” have the number of
plugs outlined in the below
diagram (Fig.3C). Follow the
diagram for complete lighting
instructions.
3.3 - Guide the extension
cord plug through the tree so
it comes out the bottom of
Section “A”. Take the
extension cord plug and plug
it into the n/ ff Remote
Control Unit that is now
plugged into your wall (See
Fig. 3B).
Fig. 3C

61246 / 7.5 ft. Royal Spruce Pro Shape Tree Page 6
Your completed tree should look like the picture below!
NOTE: Multicolor version pictured but also available with Clear Lights

61246 / 7.5 ft. Royal Spruce Pro Shape Tree Page 7
4. Storage:
Unplug the extension cord plug(s) from the Remote Unit attached to the electrical outlet on
the wall. Take off all of your ornaments and tree decorations before packing your tree back
into its storage box.
Starting from the top, gently lift off each section. Each section should be packed away in the
carton that it came in. Each tree section should be turned upside down and then carefully
press branches toward center pole for easier placement into the storage box. Carefully place
the tree in its box and tape it shut.
Your Frontgate Pro Shape Tree comes in a Expandable Storage Carton. The flaps on
the cartons are scored. This allows you to increase the size of the carton for easier storage of
your Pro Shape Tree.
DO NOT STORE TREE IN A DAMP AREA OR IN AN AREA WHERE THE
TEMPERATURE EXCEEDS 100ºF.
CARE & USE INSTRUCTIONS
•Before using, inspect products carefully. Discard any products that have cut, damaged or
frayed wire insulation or cords, cracks in the lamp holders or enclosures, loose
connections, or exposed copper wire.
•When storing the product, carefully remove the product from wherever it is placed.
•When not in use, store neatly in a cool, dry location protected from sunlight.

61246 / 7.5 ft. Royal Spruce Pro Shape Tree Page 8
IMPORTANT SAFETY INSTRUCTIONS
PLEASE READ THIS C NTENT CAREFULLY AND SAVE F R FUTURE USE
•Do not use seasonal products outdoors unless marked suitable for indoor and outdoor
use. When products are used in outdoor applications, connect the product to a Ground
Fault Circuit interrupters (GFCI) outlet. If one is not provided, contact a qualified
electrician for proper installation.
•This seasonal use product is not intended for permanent installation or use.
•Do not mount or place near gas or electric heaters, fireplaces, candles or other similar
sources of heat.
•Do not secure the wiring of the product with staples or nails, or place on sharp hooks or
nails.
•Do not let lamps rest on the supply cord or any wire.
•Unplug the product when leaving the house, when retiring for the night, or if left
unattended.
•This is an electrical product - not a toy! To avoid risk of fire, burns, personal injury and
electric shock, it should not be played with or placed where small children can reach it.
•Do not use this product for other than its intended use.
•Do not hang ornaments or other objects from cord, wire or light string.
•Do not close doors or windows on the product or extension cords as this may damage the
wire insulation.
•Never operate this product if the power cord or plug is damaged.
•This product should not be used with a voltage converter.
•Use only manufacturer specified replacement bulbs. Read and follow all instructions that
are on the product or provided with the product.
Dear Frontgate Customer:
Please contact one o our Product Specialists or assembly assistance or
questions at 1-800-537-8484 or e-mail us at ps@ rontgate.com. Specialists are
available weekdays rom 8:00 a.m. to 8:00 p.m. EST, or Saturdays rom 9:30
a.m. to 6:00 p.m. EST.

61247 / 9 ft. Royal Spruce Pro Shape Tree Page 1
F R O N T G A T E®
F R O N T G A T E®F R O N T G A T E®
F R O N T G A T E®
OUTFITTING AMERICA’S FINEST HOMES®
INSTRUCTIONS FOR:
Item# 61247 CLR / 9 ft Royal Spruce Pro Shape Tree with 1700 ct Clear Lights
Item# 61247 MUL/ 9 ft Royal Spruce Pro Shape Tree with 1700 ct Multi Lights
BILL OF MATERIAL (BOM
)
PACKED IN ONE REUSABLE CARTON
•1 EA TREE STAND (with 3 screws)
•1 EA BOTTOM SECTION OF TREE “A”
•1 EA LOWER MIDDLE SECTION OF TREE “B”
•1 EA UPPER MIDDLE SECTION OF TREE “C”
•1 EA TREE TOP SECTION OF TREE “D”
•1 EA REMOTE ON AND OFF UNIT
•1 EA WARRANTY AND INSTRUCTIONS
•1 EA PACKET OF EXTRA BULBS AND FUSES
•1 EA TREE CARTON-WITH EXPANDABLE FEATURE
•1 PAIR ARTIFICIAL CHRISTMAS TREE SHAPING GLOVES
TREE ASSEMBLY INSRUCTIONS
1 Unpack:
Carefully remove the contents from the carton and keep the carton for future storage. Some
sections of the tree may be heavy and assistance may be required. Be sure to untangle any wires
that may be caught with other items. (Please D N T forcibly remove any contents.) Remove
any outer foam wrapping from the tree and its branches (See Fig. 1A).
Fig 1A
2 Basic Assembly Steps:
CAUTION: Two people may be needed to balance and assemble tree’s upper sections
Please use a ladder, if needed, and follow all ladder safety instructions
2 1 - pen the carton and take out all the contents. All contents that are listed in the Bill of
Material section on this page should be enclosed. Locate the tree stand and assemble it by
separating the legs of the stand to form an “X” shape (See Fig. 2A). Insert each of the three

61247 / 9 ft. Royal Spruce Pro Shape Tree Page 2
screws into the holes on the stand’s middle section, being sure that screws do not extend so far
as to interfere with installation of the tree pole. Place tree stand in desired location.
Fig 2A
2 2 - Locate Tree Section “A” and remove the protective caps that are on the top and bottom
of the pole (they can be replaced when you re-pack your tree). Insert Tree Section “A” into the
tree stand (See Fig. 2B) Make sure the pole is firmly inserted into the stand, and then turn all
three screws until contact is made with the pole. If Section “A” is not sitting straight, then
simply loosen the screws, adjust tree pole, and retighten the screws.
Fig 2B
All the branches are connected to the tree’s center pole by metal hinges
(See Figure 2). Remove the packing strap that is around the tree section
and allow the branches to fall into place. As this is a FRONTGATE
Pro Shape Tree, the leaves will spring into their correct position,
ONLY MINIMAL SHAPING IS NECESSARY!!!

61247 / 9 ft. Royal Spruce Pro Shape Tree Page 3
2 3 - Locate Tree Section “B” and insert into the top of Tree Section “A”. Make sure section
“B” is seated securely into the top of section “A” (See Fig. 2C). Remove the packing strap that
is wrapped around this tree section, same as you for Section “A”. Allow the branches and
leaves to fall into place.
Fig 2C
2 4 - Locate Tree Section “C” and insert into the top of the Tree Section “B”. Make sure
section “C” is seated securely into the top of section “B” (See Fig. 2D). Remove the packing
strap that is wrapped around this tree section, same as did you for Section “B”. Allow the
branches and leaves to fall into place.
Fig 2D

61247 / 9 ft. Royal Spruce Pro Shape Tree Page 4
2 5 - Locate Tree Section “D” and insert into the top of the Tree Section “C”. Make sure
section “D” is seated securely into the top of section “C” (See Fig. 2E). Remove the packing
strap that is wrapped around this tree section, same as did you for Section “B”. Allow the
branches and leaves to fall into place.
Fig 2E

61247 / 9 ft. Royal Spruce Pro Shape Tree Page 5
3 Light Set and Power Connection:
3 1 – In the tree carton, there is a brown box that contains your n/ ff Remote Kit. Plug
your n/ ff Remote Control Unit (See Fig. 3A) into the closest electrical outlet near the tree
(See Fig. 3B). Plug the extension cords into the n/ ff Remote Control Unit. The Unit
comes with one Remote Control.
Fig 3A Fig 3B
3 2 - Your tree is lighted with miniature lights that are strung on the tree at the factory. Those
lights are plugged into the extension cords on the tree.
Your 9 ft tree will have One (1) extension cord plug Total Light Set plugs equal
Eighteen (18)
Sections “A”, “B”, “C”, and “D”
have the number of plugs outlined
in the below diagram (Fig.3C).
Follow the diagram for complete
lighting instructions.
3 3 - Guide the extension cord
plug through the tree so it comes
out the bottom of Section “A”.
Take the extension cord plug and
plug it into the n/ ff Remote
Control Unit that is now plugged
into your wall (See Fig. 3B).
Fig 3C

61247 / 9 ft. Royal Spruce Pro Shape Tree Page 6
Your tree should look like the picture below!
NOTE: Multicolor version pictured but also available with Clear Lights

61247 / 9 ft. Royal Spruce Pro Shape Tree Page 7
4 Storage:
Unplug the extension cord plug(s) from the Remote Unit attached to the electrical outlet on the
wall. Take off all of your ornaments and tree decorations before packing your tree back into its
storage box.
Starting from the top, gently lift off each section. Each section should be packed away in the
carton that it came in. Each tree section should be turned upside down and then carefully press
branches toward center pole for easier placement into the storage box. Carefully place the tree in
its box and tape it shut.
Your Frontgate Pro Shape Tree comes in a Expandable Storage Carton. The flaps on the
cartons are scored. This allows you to increase the size of the carton for easier storage of your
Pro Shape Tree.
DO NOT STORE TREE IN A DAMP AREA OR IN AN AREA WHERE THE
TEMPERATURE EXCEEDS 100ºF
CARE & USE INSTRUCTIONS
•Before using, inspect products carefully. Discard any products that have cut, damaged or
frayed wire insulation or cords, cracks in the lamp holders or enclosures, loose connections,
or exposed copper wire.
•When storing the product, carefully remove the product from wherever it is placed.
•When not in use, store neatly in a cool, dry location protected from sunlight.

61247 / 9 ft. Royal Spruce Pro Shape Tree Page 8
IMPORTANT SAFETY INSTRUCTI
ONS
PLEASE READ THIS C NTENT CAREFULLY AND SAVE F R FUTURE USE
•Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use.
When products are used in outdoor applications, connect the product to a Ground Fault
Circuit interrupters (GFCI) outlet. If one is not provided, contact a qualified electrician for
proper installation.
•This seasonal use product is not intended for permanent installation or use.
•Do not mount or place near gas or electric heaters, fireplaces, candles or other similar
sources of heat.
•Do not secure the wiring of the product with staples or nails, or place on sharp hooks or
nails.
•Do not let lamps rest on the supply cord or any wire.
•Unplug the product when leaving the house, when retiring for the night, or if left
unattended.
•This is an electrical product - not a toy! To avoid risk of fire, burns, personal injury and
electric shock, it should not be played with or placed where small children can reach it.
•Do not use this product for other than its intended use.
•Do not hang ornaments or other objects from cord, wire or light string.
•Do not close doors or windows on the product or extension cords as this may damage the
wire insulation.
•Never operate this product if the power cord or plug is damaged.
•This product should not be used with a voltage converter.
•Use only manufacturer specified replacement bulbs. Read and follow all instructions that are
on the product or provided with the product.
Dear Frontgate Customer:
Please contact one of our Product Specialists for assembly assistance or
questions at 1-800-537-8484 or e-mail us at ps@frontgate com Specialists are
available weekdays from 8:00 a m to 8:00 p m EST, or Saturdays from 9:30
a m to 6:00 p m EST

61248 / 10 ft. Royal Spruce Pro Shape Tree Page 1
F R O N T G A T E®
F R O N T G A T E®F R O N T G A T E®
F R O N T G A T E®
OUTFITTING AMERICA’S FINEST HOMES®
INSTRUCTIONS FOR:
Item# 61248 CLR / 10 ft Royal Spruce Pro Shape Tree with 1900 ct Clear Lights
Item# 61248 MUL / 10 ft Royal Spruce Pro Shape Tree with 1900 ct Multi Lights
BILL OF MATERIAL (BO
M
)
PACKED IN ONE REUSABLE CARTON
•1 EA TREE STAND (with 3 screws)
•1 EA BOTTOM SECTION OF TREE “A”
•1 EA LOWER MIDDLE SECTION OF TREE “B”
•1 EA UPPER MIDDLE SECTION OF TREE “C”
•1 EA TREE TOP SECTION OF TREE “D”
•1 EA REMOTE ON AND OFF UNIT
•1 EA WARRANTY AND INSTRUCTIONS
•1 EA PACKET OF EXTRA BULBS AND FUSES
•1 EA TREE CARTON-WITH EXPANDABLE FEATURE
•1 PAIR ARTIFICIAL CHRISTMAS TREE SHAPING GLOVES
TREE ASSEMBLY INSRUCTIONS
1 Unpack:
Carefully remove the contents from the carton and keep the carton for future storage. Some
sections of the tree may be heavy and assistance may be required. Be sure to untangle any wires
that may be caught with other items. (Please D N T forcibly remove any contents.) Remove
any outer foam wrapping from the tree and its branches (See Fig. 1A).
Fig 1A
2 Basic Assembly Steps:
CAUTION: Two people may be needed to balance and assemble tree’s upper sections
Please use a ladder, if needed, and follow all ladder safety instructions
2 1 - pen the carton and take out all the contents. All contents that are listed in the Bill of
Material section on this page should be enclosed. Locate the tree stand and assemble it by
separating the legs of the stand to form an “X” shape (See Fig. 2A). Insert each of the three

61248 / 10 ft. Royal Spruce Pro Shape Tree Page 2
screws into the holes on the stand’s middle section, being sure that screws do not extend so far
as to interfere with installation of the tree pole. Place tree stand in desired location.
Fig 2A
2 2 - Locate Tree Section “A” and remove the protective caps that are on the top and bottom
of the pole (they can be replaced when you re-pack your tree). Insert Tree Section “A” into the
tree stand (See Fig. 2B) Make sure the pole is firmly inserted into the stand, and then turn all
three screws until contact is made with the pole. If Section “A” is not sitting straight, then
simply loosen the screws, adjust tree pole, and retighten the screws.
Fig 2B
All the branches are connected to the tree’s center pole by metal hinges
(See Figure 2). Remove the packing strap that is around the tree section
and allow the branches to fall into place. As this is a FRONTGATE
Pro Shape Tree, the leaves will spring into their correct position,
ONLY MINIMAL SHAPING IS NECESSARY!!!

61248 / 10 ft. Royal Spruce Pro Shape Tree Page 3
2 3 - Locate Tree Section “B” and insert into the top of Tree Section “A”. Make sure section
“B” is seated securely into the top of section “A” (See Fig. 2C). Remove the packing strap that
is wrapped around this tree section, same as you for Section “A”. Allow the branches and
leaves to fall into place.
Fig 2C
2 4 - Locate Tree Section “C” and insert into the top of the Tree Section “B”. Make sure
section “C” is seated securely into the top of section “B” (See Fig. 2D). Remove the packing
strap that is wrapped around this tree section, same as did you for Section “B”. Allow the
branches and leaves to fall into place.
Fig 2D

61248 / 10 ft. Royal Spruce Pro Shape Tree Page 4
2 5 - Locate Tree Section “D” and insert into the top of the Tree Section “C”. Make sure
section “D” is seated securely into the top of section “C” (See Fig. 2E). Remove the packing
strap that is wrapped around this tree section, same as did you for Section “B”. Allow the
branches and leaves to fall into place.
Fig 2E