Frontgate Holiday 66637 User manual

9 ft
–ITEM
7.5 ft. Designer Lit Spruce –Item #66637

9 ft
–ITEM
7.5 ft. Designer Lit Spruce –Item #66637
PARTS LIST
A. BOTTOM NUMBER OF PERSONS
RECOMMENDED FOR SKU 66637 –7.5’Designer Lit Spruce
TREE
2387TIPSSTANDARDSTAND
B. MIDDLE
C. TOP
D. TREE STAND
ASSEMBLY: 2 U
L 1150LIGHTS
MAXDIAMETER66”
HARDWARE
A. POWER STRIP QUANTITY 1 PC
B. REMOTE CONTROL W/ RECEIVER QUANTITY 1 SET
C. EXTRA BULBS AND FUSES QUANTITY 46PCS BULBS/2 FUSES
1. Unpack:
Carefully remove the contents from the carton and keep the carton for future storage. Some sections of the
tree may be heavy and assistance may be required. Remove any outer foam wrapping from the tree and its
branches (See Fig. 1A).
2. Basic Assembly Steps:
Fig. 1A
CAUTION: Two people may be needed to balance and assemble tree’s upper sections. Please use a
ladder, if needed, and follow all ladder safety instructions.
2.1 –Open the carton and take out all the contents. All contents that are listed in the Bill of Material section
on this page should be enclosed. Locate the metal tree stand and assemble it by separating the legs of the
stand to form an “X” shape (See Fig 2A). Insert each of the three screws into the holes on the stand’s middle
section, being sure that screws do not extend so far as to interfere with installation of the tree pole. Place tree
stand in desired location.
Fig. 2A

2.2 –Locate Tree Section “A” and remove the protective caps that are on the top and bottom of the pole
(they can be replaced when you re-pack your tree). Insert Tree Section “A” into the tree stand (See Fig. 2B).
Make sure the pole is firmly inserted into the stand, and then turn all three screws until contact is made with
the pole. If Section “A” is not sitting straight, then simply loosen the screws, adjust tree pole, and retighten
the screws.
All the branches are connected to the tree’s center pole by metal hinges (See Figure 2). Remove the packing
strap that is around the tree section and allow the branches to fall into place.
2.3 –Locate Tree Section “B” and insert into the top of Tree Section “A”. Make sure section “B” is seated
securely into the top of section “A”. Remove the packing strap that is wrapped around this tree section, same
as you for Section “A”. Allow the branches and leaves to fall into place.
2.6 –Locate Tree Section “C” and insert into the top of the Tree Section “B”. Make sure section “C” is
seated securely into the top of section “B”. Remove the packing strap that is wrapped around this tree section,
same as you for Section “B”. Allow the branches and leaves to fall into place.
Fig. 2E

3. Light Set and Power Connection:
3.1 –In the tree carton, there is a brown box that contains your On/Off Remote Kit. Plug your On/Off
Remote Control Unit (See Fig. 3A) into the closest electrical outlet near the tree (See Fig. 3B). Plug the
extension cords into the On/Off Remote Control Unit. The Unit comes with one Remote Control.
Fig. 3A Fig. 3B
3.2 –Your tree is lighted with miniature lights that are strung on the tree at the factory. Those lights are
plugged into the extension cords on the tree.

STORAGE TIPS
Unplug the extension cord plugs from the Remote Unit attached to the electrical outlet on the wall. Take off all of your
ornaments and tree decorations before packing your tree back into its storage boxes.
Starting from the top, gently lift off each section. Each section should be packed away in the carton that it came in. Each tree
section should be turned upside down and then carefully press branches toward center pole for easier placement into the
storage box. Carefully place the tree in its box and tape it shut.
DO NOT STORE TREE IN A DAMP AREA OR IN AN AREA WHERE THE TEMPERATURE EXCEEDS
100ºF.

CARE & MAINTENANCE INSTRUCTION
1. This is for decorative use only - do not immerse in water or expose to heat. Keep away from fire.
2. Please use water only for cleaning purpose.
3. When not in use, store neatly in a cool, dry location protected fromsun light.
4. When the remote control has
malfunctioned, please remove the power strip fromthe receiver and plug the power strip directlyinto
the wall.
THE FOLLOWING STEPS WILL HELPMAKEYOUR TREE LOOK MORE REALISTIC
1. Light tree one section at a time as described in assemblyinstructions,so you can easily identify any bulbs that may be dislodged.
Push any loose bulbs back into their sockets.
2. Separate the branch tips to forma “V” shape and fluff the needles. Make sure each tip is spread out and no two branchesare
touching each other. For best access to branches, shape each section prior to adding the next section as described in the initial
assembly instructions. You may want to wear cotton gloves when fluffing needles to avoid scratchesand skin irritation.
3. Starting with the bottomrow, position the branches parallel to the floor. Angle the tips slightly upward like they are growing
towards the sun. With each successive row, make the upward angle of the branches more pronounced. Position inner tips to hide
the center of the tree.
4. Arrange the uppermostsection of the tree so that the tips are evenly spaced and pointing upward.
5. Step back and review the tree. Adjust branches and tips as necessaryto give the tree a fuller appearance (The tree may be shape
differently (upswept /downswept /etc.) pending on one’s preference.)
TROUBLE SHOOTINGTIPS
1. If entire tree lighting does not light, make sure power strip cords are securely inserted in a working wall outlet.
2. If an entire sectionof the tree does not light, please review following actions:
a. Check that all plugs within the tree are securelyconnected.
b. Check fuse in power strip to determine if it may need replacement.Caution: Note that a blown fuse indicates an electrical
overload or electrical short circuit. If the fuse is blown, unplug power strip from outlet.Also unplug any additional strings
or products may be attached to the power strip. Replace the fuse following manufacturer instructions with proper fuse
rating. If the replacementfuse blows, a short circuit may be present and the product should be discarded.
c. Check fuse in plug connectionon end of each light string.(See section on replacing plug fuses in this document).

TROUBLE SHOOTINGTIPS (Cont.)
3. If some individual lights do not light up, it may be due to becoming dislodged from the socket during assembly. Note those not
lit up; check for looseness and push any loose bulbs gently back into their socket. If they still do not light up, try a replacement
light bulb (supplied by manufacturer) and follow directions in section describinghow to replace light bulbs.
IMPORTANT BASIC SAFETYINSTRUCTIONS
When using electrical products, to avoid risk of fire burns, personal injury and electrical shock, basic precautionsshould always be
followed as stated below:
READ AND
FOLLOW ALL SAFETY INSTRUCTIONS
1. Do not use seasonalproducts outdoors unless marked suitable for indoor and outdoor use. When productsare used in outdoor
applications,connect the product to a Ground Fault Circuit interrupting(GFCI) outlet. If one is not provided, contact a qualified
electrician for proper installation.
2. This seasonal use product is not intended for permanent installationor use.
3. Do not mount or place near gas or electrical heaters, fireplace, candles or other similar sources of heat.
4. Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
5. Do not let lamps rest on the supplycord or on any wire.
6. For your safety, unplugthe product when leavingthe house, when retiring for the night or if left unattended.
7. This is an electrical product –not a toy! To avoid risk of fire, burns, personal injury and electric shock it should not be played
with or placed where small childrencan reach it.
8. Do not use this product for other than its intended use.
9. Do not hang ornaments or other objects fromcord, wire or light string.
10. Do not close doors or windows on the product or extensionscords as this may damage the wire insulation.
11. Do not cover the product with cloth, paper or any material not part of the product when in use.
12. This product is equipped with push-in lamps. Do not twist the lamps.
13. This product employs overload protection(fuse). A blown fuse indicatesan overload or short-circuitsituation. If the fuse blows,
unplugthe product from the outlet. Also unplug any additionalstrings or productsthat may be attached to the product. Replace
the fuse as per the user servicing instructions(followproduct marking for proper fuse rating) and check the product. If the
replacementfuse blows, a short-circuit may be present and the product should be discarded.
14. Read and followall instructionsthat are on the product or provided with the product.
CAUTION: To reduce the risk of fire and electric shock:
a. Do not install on trees having needles, leaves or branch coverings of metal or materials which look like metal, and:
b. Do not mount or support strings in a manner that can cut or damage wire insulation.

USER INSTRUCTIONS
TO REPLACE LIGHT BULBS
CAUTION: FIRST UNPLUGYOUR PRODUCT FROM ANY POWERSOURCE.
1.
To reduce the risk of overheating, replace burned-outlight bulbs promptly .Use only
2.5 volt light bulbs only.
2. Grasp plugand remove from the receptacle or any other electricaloutlet device. Do
not
unplugbypullingon the cord.
3. Pull the light bulb anditsattached plastic base straight out of light bulb holder.
4. Replace light bulb with only 2.5 volt
super bright type light (provided with product).
PULL BULB UP
TOREMOVE
t
i PUS H BULB DOWN
.... TOREPLACE
5.
If the new lamp base does not fit the replacementlight bulb, followthe steps below
before step 4.
a. Remove the base of burned out lightby straightening light leads and gently pull bulb out.
b.Thread metal leads of new lamp through hose in old base with one lead in each hold.
c. After lamp is fully insertedinto base ,bend each lead up, like other lights in the light set so that the leads will touch the
contacts inside the light socket.
TOREPLACE A FUSE:
CAUTION:FIRST UNPLUG YOUR PRODUCTFROMANY POWER SOURCE.
1. Grasp plug and remove from the receptacleor other outlet device. Do not unplug
by
pulling on cord.
2. Open fuse cover. Slide open fuse access cover on top of attachment plug towards plug's
metal prongs or blades.
FUSECOVER
SLIDES FORWARD
3. Removefuse carefully.
4. Risk of
fire. Replace fuse ONLY with 3 Amp 120 Volt fuse.(Provided with product).
5. Close fuse
cover. Return the sliding fuse cover back to its former closed position on
attachmentplug.
6. Risk of
fire. Do not replace attachment plug because it contains a safety device (fuse)
that should not be removed. Discard product if the attachment plug is damaged
Please contact one of our
Product Specialists for assembly assistanceor questionsat 1-800-537-8484or email [e-mail].
Specialists are available weekdays 8:00 a.m.to 8:00p.m.EST or Saturday 9:30 a.m. to 6:00 p.m.

9 ft
–ITEM
9 ft. Designer Lit Spruce –Item #66639