Frontgate OUTFITTING AMERICA'S FINEST HOMES 46037 CLE User manual

46037 / 7.5 ft. Nordman Fir Pro Shape FlipTree Page 1
F R O N T G A T E®
F R O N T G A T E®F R O N T G A T E®
F R O N T G A T E®
OUTFITTING AMERICA’S FINEST HOMES®
INSTRUCTIONS FOR:
Item # 46037 CLE / 7.5 t. Nordman Fir Pro Shape FlipTree with 900 ct. Clear Lights
Item # 46037 MUL / 7.5 t. Nordman Fir Pro Shape FlipTree with 900 ct. Multi Lights
BILL OF M
ATERIAL (BOM
)
PACKED IN ONE REUSABLE CARTON
•1 EA. FLIPTREE STAND with Bottom “A” Section Attached
•1 EA. TREE TOP SECTION OF TREE “B”
•1 EA. PACKET OF EXTRA BULBS AND FUSES
•1 EA. DELUXE TREE STORGAE BAGS (1 ea. Body o tree, 1 ea. Tree Top)
•1 EA. RE-USABLE TREE CARTON
•1 EA. REMOTE ON/OFF UNIT
•1 EA. WARRANTY AND INSTRUCTIONS
•1 EA. PACKET OF EXTRA BULBS AND FUSES
•1 PAIR ARTIFICIAL CHRISTMAS TREE SHAPING GLOVES
TREE ASSEMBLY INSRUCTIONS
1. Unpack:
Carefully place Tree Carton upright with arrows pointing toward the ceiling. Open the carton
by cutting down taped sides and opening the carton’s flaps. The carton can be kept for future
storage, thrown away, or put into your recycle bins for pickup.
The Tree comes with its own torage Bags (One for the Body of the Tree and One for the One
Piece Tree Top). These torage Bags are put on each section of the Tree by the Factory. ee
Figure 1A.
Fig. 1A

46037 / 7.5 ft. Nordman Fir Pro Shape FlipTree Page 2
2. Getting Tree into the Ready Position:
The Pro hape FlipTree is resting on a tyrofoam or Cardboard pad. Remove the Pad from
under the tand.
IMPORTANT: THE TREE STAND IS ATTACHED TO THE TREE BY THE
FACTORY, AND IT SHOULD NOT BE REMOVED FROM THE TREE.
The Tree Top that is packed in its torage Bag should be taken out of the carton and put to the
side until needed. The Tree Top assembly instructions are listed below.
GETTING YOUR TREE READY TO FLIP!!! Unlock the wheels and slowly wheel out
your tree from its Carton to the desired tree setup location in your home or office. Give
yourself enough room to Unbuckle and Unzip the Bag and carefully take it off the “A” or Main
Body of the Tree. (Please store this in a sa e place as you will use this bag again to store
the tree a ter the Christmas Season!!)
Once you have your tree set in the location that you want to put up the tree, LOCK the two
front wheels!! ee Figure 2A below.
Fig. 2A
NOTE: WHEN FLIPPING THE TREE, MAKE SURE THAT YOU HAVE
ENOUGH ROOM FOR THE TREE TO FLIP UPWARD. MAKE SURE YOU ARE
NOT TOO CLOSE TO A WALL, FURNTURE LAMP, OR LOW HANGING LIGHT
FIXTURES.
3. Flip Action:
Now your Tree ection “A” is ready to Flip, Locate the Flip path indicator button at the top of
the Flip Pole. The Flip path runs the length of the Flip pole and is designated by the arrow on
the indicator button. The Tree is made so no Electrical Cords impede flipping the tree. ome
limbs may temporarily catch on each other during storage or shipping. As your start flipping
over your tree you can clear the Flip path of these branches and leaves by just pushing the
bottom branches either left of right.
After you remove the torage bag, the tree will be in an upside down position. ee Fig 3A. Flip
the tree by pulling the top Flip path indicator button towards you in the direction of the arrow.
As you Flip the Tree with one hand, continue to clear the Flip path of any caught limbs with
your other hand ( ee Fig 3B) until the tree is totally upright ( ee Fig 3C). The Indicator button
that was on the top of the Flip pole is now at the base and should be flush against the support
pole.

46037 / 7.5 ft. Nordman Fir Pro Shape FlipTree Page 3
As your Flip Tree is turning, the branches will fall into place as all the tree branches are on
hinges. Your FRONTGATE tree is also made with a PRO SHAPE
CONSTRUCTION which means all o the leaves will spring into place...
Only Minimal shaping is required with your newly purchased PRO
SHAPE FLIPTREE!
Your FlipTree comes with a Fliplock system. Once the tree is totally upright, you will want to
lock the tree into place using our factory installed attached lock in band ( ee Fig 3D). Wrap the
band around the bottom of the tree and also around the Flip Tree upport bar. Push in the two
prong lock clip into the female plastic housing ( ee Fig 3E). It will lock with a Click. To take
off the lock, push on both sides of the clip, and it will release (this step should be done only
when the tree is being readied for storage).
Fig 3A Fig 3B Fig 3C Fig 3D Fig 3E
4. Tree Top Assembly:
Now that you tree is upright and the locked into place, take your tree top, Tree ection “B”,
and place it into the top part of the pole ( ee Figure 3F).
Fig 3F

46037 / 7.5 ft. Nordman Fir Pro Shape FlipTree Page 4
5. Light Set and Power Connection
There are 3 Light set plugs that
will come out of the bottom of
the Tree Top ection “B”.
They are to be plugged into the
extension cord tap that will be
located near the top of Tree
ection “A”. Place your tree
top into the top of section “A”,
plug in your lights and you are
ready to decorate. It’s that
easy!!!
YOUR FlipTree has only one
extension cord to plug in. This
extension cord is attached to
the tree by the factory, and the
miniature light plugs for Tree
ection “A” are already
plugged into this extension
cord.
YOUR FLIP TREE IS NOW READY TO DECORATE!!

46037 / 7.5 ft. Nordman Fir Pro Shape FlipTree Page 5
6. To store your PRO SHAPE FlipTree:
a. Unplug the Tree’s extension cord from the wall outlet.
b. Unplug the Tree Top’s light set plugs from the Tree’s upper extension cord tap.
c. Take off the Tree Top and place it into the Tree Top storage bag.
d. Un-couple the Flip Lock trap from the bottom of the tree.
e. Put your foot on BA E OF THE TAND and push the Tree away from you, the
Tree will start to move back into its upside down position. Remember to tip the Tree
slowly and move any branches that may be getting in the way. Make sure that the
Tree is 100% in the upside down position before putting the Tree’s storage bag on
the Tree.
f. Place the storage bag around the Tree. Make sure the zipper is fully opened.
g. Pull the bag down and attach the Velcro straps around the legs of the stand.
h. Unlock your Tree’s stand wheels, and you are ready to roll your Tree off to storage. To go
up and down steps, you can lift the Tree using the Tree’s bag handles. When moving this
Tree into storage, it is recommended that another person assist for safety reasons.
DO NOT STORE YOUR TREE IN A DAMP AREA OR IN AN AREA WHERE THE
TEMPERATURE EXCEEDS 100ºF.

46037 / 7.5 ft. Nordman Fir Pro Shape FlipTree Page 6
CARE & USE INSTRUCTIONS
•Before using, inspect products carefully. Discard any products that have cut, damaged or
frayed wire insulation or cords, cracks in the lamp holders or enclosures, loose connections,
or exposed copper wire.
•When storing the product, carefully remove the product from wherever it is placed.
•When not in use, store neatly in a cool, dry location protected from sunlight.

46037 / 7.5 ft. Nordman Fir Pro Shape FlipTree Page 7
IMPORTANT SAFETY INSTRUCTIONS
PLEASE READ THIS CONTENT CAREFULLY AND SAVE FOR FUTURE USE
•Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use.
When products are used in outdoor applications, connect the product to a Ground Fault
Circuit interrupters (GFCI) outlet. If one is not provided, contact a qualified electrician for
proper installation.
•This seasonal use product is not intended for permanent installation or use.
•Do not mount or place near gas or electric heaters, fireplaces, candles or other similar
sources of heat.
•Do not secure the wiring of the product with staples or nails, or place on sharp hooks or
nails.
•Do not let lamps rest on the supply cord or any wire.
•Unplug the product when leaving the house, when retiring for the night, or if left
unattended.
•This is an electrical product - not a toy! To avoid risk of fire, burns, personal injury and
electric shock, it should not be played with or placed where small children can reach it.
•Do not use this product for other than its intended use.
•Do not hang ornaments or other objects from cord, wire or light string.
•Do not close doors or windows on the product or extension cords as this may damage the
wire insulation.
•Never operate this product if the power cord or plug is damaged.
•This product should not be used with a voltage converter.
•Use only manufacturer specified replacement bulbs. Read and follow all instructions that
are on the product or provided with the product.
Dear Frontgate Customer:
Please contact one o our Product Specialists or assembly assistance or
questions at 1-800-537-8484 or e-mail us at ps@ rontgate.com. Specialists
are available weekdays rom 8:00 a.m. to 8:00 p.m. EST, or Saturdays rom
9:30 a.m. to 6:00 p.m. EST.

46039 / 9 ft. Nordman Fir Pro Shape FlipTree Page 1
F R O N T G A T E®
F R O N T G A T E®F R O N T G A T E®
F R O N T G A T E®
OUTFITTING AMERICA’S FINEST HOMES®
INSTRUCTIONS FOR:
Item # 46039 CLE / 9 ft. N rdman Fir Pr Shape FlipTree with 1100 ct. Clear Lights
Item # 46039 MUL / 9 ft. N rdman Fir Pr Shape FlipTree with 1100 ct. Multi Lights
BILL OF MAT
ERIAL (BOM
)
PACKED IN ONE REUSABLE CARTON
•1 EA. FLIPTREE STAND with B tt m “A” Secti n Attached
•1 EA. TREE TOP SECTION OF TREE “B”
•1 EA. PACKET OF EXTRA BULBS AND FUSES
•1 EA. DELUXE TREE STORGAE BAGS (1 ea. B dy f tree, 1 ea. Tree T p)
•1 EA. RE-USABLE TREE CARTON
•1 EA. REMOTE ON/OFF UNIT
•1 EA. WARRANTY AND INSTRUCTIONS
•1 EA. PACKET OF EXTRA BULBS AND FUSES
•1 PAIR ARTIFICIAL CHRISTMAS TREE SHAPING GLOVES
TREE ASSEMBLY INSRUCTIONS
1. Unpack:
Carefully place Tree Carton upright with arrows pointing toward the ceiling. Open the carton
by cutting down taped sides and opening the carton’s flaps. The carton can be kept for future
storage, thrown away, or put into your recycle bins for pickup.
The Tree comes with its own torage Bags (One for the Body of the Tree and One for the One
Piece Tree Top). These torage Bags are put on each section of the Tree by the Factory. ee
Figure 1A.
Fig. 1A

46039 / 9 ft. Nordman Fir Pro Shape FlipTree Page 2
2. Getting Tree int the Ready P siti n:
The Pro hape FlipTree is resting on a tyrofoam or Cardboard pad. Remove the Pad from
under the tand.
IMPORTANT: THE TREE STAND IS ATTACHED TO THE TREE BY THE
FACTORY, AND IT SHOULD NOT BE REMOVED FROM THE TREE.
The Tree Top that is packed in its torage Bag should be taken out of the carton and put to the
side until needed. The Tree Top assembly instructions are listed below.
GETTING YOUR TREE READY TO FLIP!!! Unlock the wheels and slowly wheel out
your tree from its Carton to the desired tree setup location in your home or office. Give
yourself enough room to Unbuckle and Unzip the Bag and carefully take it off the “A” or Main
Body of the Tree. (Please st re this in a safe place as y u will use this bag again t st re
the tree after the Christmas Seas n!!)
Once you have your tree set in the location that you want to put up the tree, LOCK the two
front wheels!! ee Figure 2A below.
Fig. 2A
NOTE: WHEN FLIPPING THE TREE, MAKE SURE THAT YOU HAVE
ENOUGH ROOM FOR THE TREE TO FLIP UPWARD. MAKE SURE YOU ARE
NOT TOO CLOSE TO A WALL, FURNTURE LAMP, OR LOW HANGING LIGHT
FIXTURES.
3. Flip Acti n:
Now your Tree ection “A” is ready to Flip, Locate the Flip path indicator button at the top of
the Flip Pole. The Flip path runs the length of the Flip pole and is designated by the arrow on
the indicator button. The Tree is made so no Electrical Cords impede flipping the tree. ome
limbs may temporarily catch on each other during storage or shipping. As your start flipping
over your tree you can clear the Flip path of these branches and leaves by just pushing the
bottom branches either left of right.
After you remove the torage bag, the tree will be in an upside down position. ee Fig 3A. Flip
the tree by pulling the top Flip path indicator button towards you in the direction of the arrow.
As you Flip the Tree with one hand, continue to clear the Flip path of any caught limbs with
your other hand ( ee Fig 3B) until the tree is totally upright ( ee Fig 3C). The Indicator button
that was on the top of the Flip pole is now at the base and should be flush against the support
pole.

46039 / 9 ft. Nordman Fir Pro Shape FlipTree Page 3
As your Flip Tree is turning, the branches will fall into place as all the tree branches are on
hinges. Y ur FRONTGATE tree is als made with a PRO SHAPE
CONSTRUCTION which means all f the leaves will spring int place...
Only Minimal shaping is required with y ur newly purchased PRO
SHAPE FLIPTREE!
Your FlipTree comes with a Fliplock system. Once the tree is totally upright, you will want to
lock the tree into place using our factory installed attached lock in band ( ee Fig 3D). Wrap the
band around the bottom of the tree and also around the Flip Tree upport bar. Push in the two
prong lock clip into the female plastic housing ( ee Fig 3E). It will lock with a Click. To take
off the lock, push on both sides of the clip, and it will release (this step should be done only
when the tree is being readied for storage).
Fig 3A Fig 3B Fig 3C Fig 3D Fig 3E
4. Tree T p Assembly:
Now that you tree is upright and the locked into place, take your tree top, Tree ection “B”,
and place it into the top part of the pole ( ee Figure 3F).
Fig 3F

46039 / 9 ft. Nordman Fir Pro Shape FlipTree Page 4
5. Light Set and P wer C nnecti n
There are 3 Light set plugs that will
come out of the bottom of the Tree
Top ection “B”. They are to be
plugged into the extension cord tap
that will be located near the top of
Tree ection “A”. Place your tree
top into the top of section “A”, plug
in your lights and you are ready to
decorate. It’s that easy!!!
YOUR FlipTree has only one
extension cord to plug in. This
extension cord is attached to the
tree by the factory, and the
miniature light plugs for Tree
ection “A” are already plugged into
this extension cord.
YOUR FLIP TREE IS NOW READY TO DECORATE!!

46039 / 9 ft. Nordman Fir Pro Shape FlipTree Page 5
6. T st re y ur PRO SHAPE FlipTree:
a. Unplug the Tree’s extension cord from the wall outlet.
b. Unplug the Tree Top’s light set plugs from the Tree’s upper extension cord tap.
c. Take off the Tree Top and place it into the Tree Top storage bag.
d. Un-couple the Flip Lock trap from the bottom of the tree.
e. Put your foot on BA E OF THE TAND and push the Tree away from you, the
Tree will start to move back into its upside down position. Remember to tip the Tree
slowly and move any branches that may be getting in the way. Make sure that the
Tree is 100% in the upside down position before putting the Tree’s storage bag on
the Tree.
f. Place the storage bag around the Tree. Make sure the zipper is fully opened.
g. Pull the bag down and attach the Velcro straps around the legs of the stand.
h. Unlock your Tree’s stand wheels, and you are ready to roll your Tree off to storage. To go
up and down steps, you can lift the Tree using the Tree’s bag handles. When moving this
Tree into storage, it is recommended that another person assist for safety reasons.
DO NOT STORE YOUR TREE IN A DAMP AREA OR IN AN AREA WHERE THE
TEMPERATURE EXCEEDS 100ºF.

46039 / 9 ft. Nordman Fir Pro Shape FlipTree Page 6
CARE & USE INSTRUCTIONS
•Before using, inspect products carefully. Discard any products that have cut, damaged or
frayed wire insulation or cords, cracks in the lamp holders or enclosures, loose connections,
or exposed copper wire.
•When storing the product, carefully remove the product from wherever it is placed.
•When not in use, store neatly in a cool, dry location protected from sunlight.

46039 / 9 ft. Nordman Fir Pro Shape FlipTree Page 7
IMPORTANT SAFETY INSTRUCTIONS
PLEASE READ THIS CONTENT CAREFULLY AND SAVE FOR FUTURE USE
•Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use.
When products are used in outdoor applications, connect the product to a Ground Fault
Circuit interrupters (GFCI) outlet. If one is not provided, contact a qualified electrician for
proper installation.
•This seasonal use product is not intended for permanent installation or use.
•Do not mount or place near gas or electric heaters, fireplaces, candles or other similar
sources of heat.
•Do not secure the wiring of the product with staples or nails, or place on sharp hooks or
nails.
•Do not let lamps rest on the supply cord or any wire.
•Unplug the product when leaving the house, when retiring for the night, or if left
unattended.
•This is an electrical product - not a toy! To avoid risk of fire, burns, personal injury and
electric shock, it should not be played with or placed where small children can reach it.
•Do not use this product for other than its intended use.
•Do not hang ornaments or other objects from cord, wire or light string.
•Do not close doors or windows on the product or extension cords as this may damage the
wire insulation.
•Never operate this product if the power cord or plug is damaged.
•This product should not be used with a voltage converter.
•Use only manufacturer specified replacement bulbs. Read and follow all instructions that
are on the product or provided with the product.
Dear Fr ntgate Cust mer:
Please c ntact ne f ur Pr duct Specialists f r assembly assistance r
questi ns at 1-800-537-8484 r e-mail us at ps@fr ntgate.c m. Specialists
are available weekdays fr m 8:00 a.m. t 8:00 p.m. EST, r Saturdays fr m
9:30 a.m. t 6:00 p.m. EST.

46040 / 10 ft. Nordman Fir Pro Shape FlipTree Page 1
F R O N T G A T E®
F R O N T G A T E®F R O N T G A T E®
F R O N T G A T E®
OUTFITTING AMERICA’S FINEST HOMES®
INSTRUCTIONS FOR:
Item # 46040 CLE / 10 ft. No dman Fi P o Shape FlipT ee with 1250 ct. Clea Lights
Item # 46040 MUL / 10 ft. No dman Fi P o Shape FlipT ee with 1250 ct. Multi Lights
BILL OF M
ATERIAL (BOM
)
PACKED IN ONE REUSABLE CARTON
•1 EA. FLIP TREE STAND with Bottom “A” Section Attached
•1 EA. LOWER TREE TOP SECTION “B”
•1 EA UPPER TREE TOP SECTION “C”
•1 EA. PACKET OF EXTRA BULBS AND FUSES
•1 EA. DELUXE TREE STORGAE BAGS (1 ea. Body of t ee, 1 ea. Uppe T ee Top,
1 ea. Lowe T ee Top)
•1 EA. RE-USABLE TREE CARTON
•1 EA. REMOTE ON/OFF UNIT
•1 EA. WARRANTY AND INSTRUCTIONS
•1 EA. PACKET OF EXTRA BULBS AND FUSES
•1 PAIR ARTIFICIAL CHRISTMAS TREE SHAPING GLOVES
TREE ASSEMBLY INSRUCTIONS
1. Unpack:
Carefully place Tree Carton upright with arrows
pointing toward the ceiling. Open the carton by cutting
down taped sides and opening the carton’s flaps. The
carton can be kept for future storage, thrown away, or
put into your recycle bins for pickup.
The Tree comes with its own torage Bags (One for the
Body of the Tree, One for the Lower Tree Top ection
“B”, and One for the Upper Tree Top ection “C”).
These torage Bags are put on each section of the tree
by the Factory. ee Figure 1A.
Fig. 1A

46040 / 10 ft. Nordman Fir Pro Shape FlipTree Page 2
2. Getting T ee into the Ready Position:
The Pro hape FlipTree is resting on a tyrofoam or Cardboard pad. Remove the Pad from
under the tand.
IMPORTANT: THE TREE STAND IS ATTACHED TO THE TREE BY THE
FACTORY, AND IT SHOULD NOT BE REMOVED FROM THE TREE.
The Tree Top that is packed in its torage Bag should be taken out of the carton and put to the
side until needed. The Tree Top assembly instructions are listed below.
GETTING YOUR TREE READY TO FLIP!!! Unlock the wheels and slowly wheel out
your tree from its Carton to the desired tree setup location in your home or office. Give
yourself enough room to Unbuckle and Unzip the Bag and carefully take it off the “A” or Main
Body of the Tree. (Please sto e this in a safe place as you will use this bag again to sto e
the t ee afte the Ch istmas Season!!)
Once you have your tree set in the location that you want to put up the tree, LOCK the two
front wheels!! ee Figure 2A below.
Fig. 2A
NOTE: WHEN FLIPPING THE TREE, MAKE SURE THAT YOU HAVE
ENOUGH ROOM FOR THE TREE TO FLIP UPWARD. MAKE SURE YOU ARE
NOT TOO CLOSE TO A WALL, FURNTURE LAMP, OR LOW HANGING LIGHT
FIXTURES.
3. Flip Action:
Now your Tree ection “A” is ready to Flip, Locate the Flip path indicator button at the top of
the Flip Pole. The Flip path runs the length of the Flip pole and is designated by the arrow on
the indicator button. The Tree is made so no Electrical Cords impede flipping the tree. ome
limbs may temporarily catch on each other during storage or shipping. As your start flipping
over your tree you can clear the Flip path of these branches and leaves by just pushing the
bottom branches either left of right.
After you remove the torage bag, the tree will be in an upside down position. ee Fig 3A. Flip
the tree by pulling the top Flip path indicator button towards you in the direction of the arrow.
As you Flip the Tree with one hand, continue to clear the Flip path of any caught limbs with
your other hand ( ee Fig 3B) until the tree is totally upright ( ee Fig 3C). The Indicator button
that was on the top of the Flip pole is now at the base and should be flush against the support
pole.

46040 / 10 ft. Nordman Fir Pro Shape FlipTree Page 3
As your Flip Tree is turning, the branches will fall into place as all the tree branches are on
hinges. You FRONTGATE t ee is also made with a PRO SHAPE
CONSTRUCTION which means all of the leaves will sp ing into place...
Only Minimal shaping is equi ed with you newly pu chased PRO
SHAPE FLIPTREE!
Your FlipTree comes with a Fliplock system. Once the tree is totally upright, you will want to
lock the tree into place using our factory installed attached lock in band ( ee Fig 3D). Wrap the
band around the bottom of the tree and also around the Flip Tree upport bar. Push in the two
prong lock clip into the female plastic housing ( ee Fig 3E). It will lock with a Click. To take
off the lock, push on both sides of the clip, and it will release (this step should be done only
when the tree is being readied for storage).
Fig 3A Fig 3B Fig 3C Fig 3D Fig 3E
4. T ee Top Assembly:
Now that you tree is upright and locked into place, next step is place the tree tops on. The
Tree Top is in two pieces, ection “B” and ection “C”.
Place ection “B” into the top of Tree ection “A” ( ee Fig. 3F and 3G). Next, put ection
“C” into the top of ection “B” ( ee Fig. 3H).
Fig. 3F Fig. 3G Fig. 3H

46040 / 10 ft. Nordman Fir Pro Shape FlipTree Page 4
5. Light Set and Powe Connection
There are 2 Light et plugs that
will come out of the bottom of
the Lower Tree Top ( ection B),
they are to be plugged into the
extension cord tap that will be
located near the top of Tree
ection “A”.
Next, there are 2 plugs coming
out of the bottom of Upper Tree
Top ( ection C) – one plug is
already inserted into the back of
the other plug. These two plugs
are to be plugged into the end of
the End Connector Light et on
the top of Tree ection “B”.
YOUR FlipTree has one
extension cord to plug in. This extension cord is attached to the Tree by the factory and the
miniature light set plugs for Tree ection A are already plugged into this extension cord.
Plug in your lights and you are ready to decorate. It’s that easy!!!
YOUR FLIP TREE IS NOW READY TO DECORATE!!!

46040 / 10 ft. Nordman Fir Pro Shape FlipTree Page 5
6. To sto e you PRO SHAPE FlipT ee:
a. Unplug the Tree’s extension cord from the wall outlet.
b. Unplug the Tree Top’s light set plugs from the Tree’s upper extension cord tap.
c. Take off the Tree Top and place it into the Tree Top storage bag.
d. Un-couple the Flip Lock trap from the bottom of the tree.
e. Put your foot on BA E OF THE TAND and push the Tree away from you, the
Tree will start to move back into its upside down position. Remember to tip the Tree
slowly and move any branches that may be getting in the way. Make sure that the
Tree is 100% in the upside down position before putting the Tree’s storage bag on
the Tree.
f. Place the storage bag around the Tree. Make sure the zipper is fully opened.
g. Pull the bag down and attach the Velcro straps around the legs of the stand.
h. Unlock your Tree’s stand wheels, and you are ready to roll your Tree off to storage. To go
up and down steps, you can lift the Tree using the Tree’s bag handles. When moving this
Tree into storage, it is recommended that another person assist for safety reasons.
DO NOT STORE YOUR TREE IN A DAMP AREA OR IN AN AREA WHERE THE
TEMPERATURE EXCEEDS 100ºF.

46040 / 10 ft. Nordman Fir Pro Shape FlipTree Page 6
CARE & USE INSTRUCTIONS
•Before using, inspect products carefully. Discard any products that have cut, damaged or
frayed wire insulation or cords, cracks in the lamp holders or enclosures, loose connections,
or exposed copper wire.
•When storing the product, carefully remove the product from wherever it is placed.
•When not in use, store neatly in a cool, dry location protected from sunlight.