Frontgate Holiday 61547 User manual

7.5 ft – ITEM

7.5 ft – ITEM
PARTS LIST
A. BOTTOMC
OLO RC O D E O NPLUG
RED NUMBER OF PERSONS
RECOMMENDED FORSKU 61547 – 7.5’ Eastern Fir TREE
3243TIPSFLIP STAND
B. MIDDLE
BLUE
C.
TOP GREEN ASSEMBLY: 2 U
L 1200LIGHTS
MAX DIAMETER 60”
HARDWARE
A. TREE BAG QUANTITY 1 SET
B. POWER STRIP QUANTITY 1 PC
C. REMOTE CONTROL W/ RECEIVER QUANTITY 1 SET
D. EXTRA BULBS AND FUSES QUANTITY EACH 18 PCS
ASSEMBLY INS T RUC T I O NS
Step 1.
Lay the carton flat, remove the tree top, instruction
sheet and all remaining parts from the shipping
container and put to the side until needed. PLEASE
READ THE ASSEMBLY INSTRUCTIONS
CAREFULLY WHEN SETTING UP THE FLIP
TREE.
Step 2.
To make it easier to remove your FLIPTREE®, it is
recommended to close the carton flaps and reposition the
tree carton flat on floor with arrows pointing upright.
Please note, the tree is packed with storage bag, the flip
stand is attached to the tree and should never be removed.
SECTION A
TREE BODY
SECTION B
MIDDLE SECTION
SECTION C
TREE TOP

Step 3
Before moving your FLIPTREE® make sure you have created a safe display location for your tree by removing
any items or furniture that may hit your tree during the flipping process. Using the green handle located near the
top of the main tree storage bag, tilt the tree back and slowly wheel it to its final display location. DO NOT
ATTACH TREE TOP TO MAIN BAG UNTIL THE TREE IS IN ITS FINAL STORAGE LOCATION.
Green Handle
Step 4
Press down the locking tabs on both front wheels once
the tree is in its desired location.
Locking Tabs
Step 5.
Remove the main tree storage bag. Unbuckle both cinch
straps located on the sides of the main bag. Then, unbuckle
the two stability straps at the bottom of the bag before
unzipping and removing the main bag. Unzip the tree top
and remove the bag.
Step 6.
Your FLIPTREE® requires one or two people to flip into
the display or storage position, anyone not assisting in
flipping your tree should stand at a safe distance. Young
children should not assist in flipping a FLIPTREE®.

Step 7.
With your foot on the footrest begin pulling the tree in the direction shown by the FLIPTREE® Indicator
(towards you and down to the center of the foot pedal). If you find it difficult to attach the tree top with
the tree in the full upright position you may choose to tilt the tree slightly for easier access.
Indicator

Step 8
Once you have finished flipping your tree, attach the
middle section B into body section A, insert tree top
section C into section B. Then plug light set of
section C into section B. Plug light set of section B
into power strip.
T OP SECTION C
(GREEN
PLUG)
MIDDLE SECTION B
(BLUE
PLUG)
R EMOTE CONTROL
and
P LUG-IN REMO TE
CONTROL RECEIVER
Wall Outlet
FLIP
B OTTOM SECTION A
(RED PLUG)
Step 9
Buckle the safety strap at the bottom of the tree.
Drawing not to Scale
Step 10
Plug the light set of tree body A into power strip. Plug power strip into the remote control receiver. Plug the
remote control received into wall outlet.

STORAGE TIPS
Step 1.
Unplug the cord connecting the tree lights to the
remote and wall socket.
Step 2.
Unplug the lights connecting the tree sections.
Step 3.
Remove the tree top and middle section and
place
both
in the tree top storage bag. If you find it diffi-
cult to remove the tree top sections in this
position
you may wish to unbuckle the safety latch and tilt the
tree slightly for easier access.
Step 4.
Check that front wheels are locked.
Step 5.
Unbuckle safety strap.
Step 6.
With your foot on the footrest begin pulling the tree
up and away from the foot pedal.
Step 7.
Place the main tree storage bag over the top of the
tree making sure the zipper is aligned with the center
of the footrest.
Step 8.
Gently pull the bag down over the tree until the bag
nearly touches the floor. Then zip up the bag.
Step 9.
Loop each of the stability straps at the bottom of the
main tree bag around the back base leg before
connecting buckle to the main bag.
Step 10.
Fasten the two cinch straps on both sides of the main
tree bag. Connect the green handle strap located near
the zipper of the main tree bag.
Step 11.
Unlock the front wheels, grab the green handle, tilt
the tree back, and proceed to wheel the tree to its final
storage location. DO NOT ATTACH TREE TOP TO
MAIN BAG UNTIL THE TREE IS IN ITS FINAL
STORAGE LOCATION.
Step 12.
To attach the tree top to the main bag, place the tree
top pole in the footrest hole and connect using the
straps found on the main bag.

CARE & MAINTENANCE INSTRUCTION
1. This is for decorative use only - do not immerse in water or expose to heat. Keep away from fire.
2. Please use water only for cleaning purpose.
3. When not in use, store neatly in a cool, dry location protected from sun light.
4. When the remote control has malfunctioned, please remove the power strip from the receiver and plug the power strip directly into
the wall.
THE FOLLOWINGSTEPS WILL HELPMAKE YOUR TREE LOOK MORE REALISTIC
1. Light tree one section at a time as described in assembly instructions, so you can easily identify any bulbs that may be dislodged.
Push any loose bulbs back into their sockets.
2. Separate the branch tips to form a “V” shape and fluff the needles. Make sure each tip is spread out and no two branches are
touching each other. For best access to branches, shape each section prior to adding the next section as described in the initial
assembly instructions. You may want to wear cotton gloves when fluffing needles to avoid scratches and skin irritation.
3. Starting with the bottom row, position the branches parallel to the floor. Angle the tips slightly upward like they are growing
towards the sun. With each successive row, make the upward angle of the branches more pronounced. Position inner tips to hide
the center of the tree.
4. Arrange the uppermost section of the tree so that the tips are evenly spaced and pointing upward.
5. Step back and review the tree. Adjust branches and tips as neccessary to give the tree a fuller appearance (The tree may be shape
differently (upswept /downswept /etc.) pending on one’s preference.)
TROUBLE SHOOTINGTIPS
1. If entire tree lighting does not light, make sure power strip cords are securely inserted in a working wall outlet.
2. If an entire section of the tree does not light, please review following actions:
a. Check that all plugs within the tree are securely connected.
b. Check fuse in power strip to determine if it may need replacement. Caution: Note that a blown fuse indicates an electrical
overload or electrical short circuit. If the fuse is blown, unplug power strip from outlet. Also unplug any additional strings
or products may be attached to the power strip. Replace the fuse following manufacturer instructions with proper fuse
rating. If the replacement fuse blows, a short circuit may be present and the product should be discarded.
c. Check fuse in plug connection on end of each light string.(See section on replacing plug fuses in this document).

TROUBLE SHOOTINGTIPS (Cont.)
3. If some individual lights do not light up, it may be due to becoming dislodged from the socket during assembly. Note those not
lit up; check for looseness and push any loose bulbs gently back into their socket. If they still do not light up, try a replacement
light bulb (supplied by manufacturer) and follow directions in section describing how to replace light bulbs.
IMPORTANT BASIC SAFETY INSTRUCTIONS
When using electrical products, to avoid risk of fire burns, personal injury and electrical shock, basic precautions should always be
followed as stated below:
READ AND
FOLLOW ALL SAFETY INSTRUCTIONS
1. Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor
applications, connect the product to a Ground Fault Circuit interrupting (GFCI) outlet. If one is not provided, contact a qualified
electrician for proper installation.
2. This seasonal use product is not intended for permanent installation or use.
3. Do not mount or place near gas or electrical heaters, fireplace, candles or other similar sources of heat.
4. Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
5. Do not let lamps rest on the supply cord or on any wire.
6. For your safety, unplug the product when leaving the house, when retiring for the night or if left unattended.
7. This is an electrical product – not a toy! To avoid risk of fire, burns, personal injury and electric shock it should not be played
with or placed where small children can reach
it.
8. Do not use this product for other than its intended use.
9. Do not hang ornaments or other objects from cord, wire or light string.
10.Do not close doors or windows on the product or extensions cords as this may damage the wire insulation.
11. Do not cover the product with cloth, paper or any material not part of the product when in use.
12. This product is equipped with push-in lamps. Do not twist the lamps.
13. This product employs overload protection (fuse). Ablown fuse indicates an overload or short-circuit situation. If the fuse blows,
unplug the product from the outlet. Also unplug any additional strings or products that may be attached to the product. Replace
the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the
replacement fuse blows, a short-circuit may be present and the product should be discarded.
14. Read and follow all instructions that are on the product or provided with the product.
CAUTION: To reduce the risk of fire and electric shock:
a. Do not install on trees having needles, leaves or branch coverings of metal or materials which look like metal, and:
b. Do not mount or support strings in a manner that can cut or damage wire insulation.

USER INSTRUCTIONS
TO REPLACE LIGHT BULBS
CAUTION: FIRST UNPLUG YOUR PRODUCT FROM ANY POWER SOURCE.
1.
T o reduce th e risk of overheating,replace burned-out light bulbs promptly .Use only
2.5 volt light bulbs only.
2. Grasp plug and remove from the receptacle or any other electrical outlet device. Do
not
unplug by pulling on the cord.
3. Pull the light bulb
and its attached plastic base straight out of light bulb holder.
4. Replace light bulb with only 2.5 volt
super bright type light (provided with product).
PULL BULB UP
TOREMOVE
t
i PUS H BULB DOWN
.... TOREPLACE
5.
If the new lamp base does not fit th e replacement light bulb, follow the steps below
before step
4.
a. Remove the base of burned out light by
straightenin g light leads and gently pull bulb out.
b.Thread metal leads of new lamp through hose in old base with one lead in each hold.
c. After lamp is fully inserted into base , bend each lead up, like other lights in the light set so that the leads will touch the
contacts inside
th e light socket.
TOREPLACE A FUSE:
CAUTION: FIRST UNPLUGYOUR PRODUCT FRO M ANY POWER SOURCE.
1. Grasp plug and remove from the receptacle or other outlet device.Do not unplug
by
pulling on cord.
2. Open fuse cover. Slide openfuse access cover on top of attachment plugtowards
plug's
metal prongs or blades.
3. Remove fuse carefully.
4. Risk of fire.Replace fuse
ONL Ywith 3 Amp 120 Volt fuse. (Provided with product).
5. Close fuse cover.Return the sliding fuse cover
back to its former closed position on
attachment plug.
6. Risk of fire.Do not replace attachment plug becauseit contains
a safety device ( fuse )
that should not be removed.
Discardproduct if the attachment plug is damaged
FUSECOVER
SLIDES FORWARD
Please contact one of our
Product Specialists for assembly assistance or questions at 1-800-537-8484 or email [e-mail].
Specialists are available weekdays 8:00 a.m.to
8:00p.m.EST or Saturday 9:30 a.m. to 6:00 p.m.

9ft – ITEM

9ft – ITEM
PARTS LIST
A. BOTTOMC
OLO RC O D E O NPLUG
RED NUMBER OF PERSONS
RECOMMENDED FORSKU 61549 - 9’ Eastern Fir TREE
4701TIPSFLIP STAND
B. MIDDLE
BLUE
C.
TOP GREEN ASSEMBLY: 2 U
L 1700LIGHTS
MAX DIAMETER 66”
HARDWARE
A. TREE BAG QUANTITY 1 SET
B. POWER STRIP QUANTITY 1 PC
C. REMOTE CONTROL W/ RECEIVER QUANTITY 1 SET
D. EXTRA BULBS AND FUSES QUANTITY EACH 18 PCS
ASSEMBLY INS T RUC T I O NS
Step 1.
Lay the carton flat, remove the tree top, instruction
sheet and all remaining parts from the shipping
container and put to the side until needed. PLEASE
READ THE ASSEMBLY INSTRUCTIONS
CAREFULLY WHEN SETTING UP THE FLIP
TREE.
Step 2.
To make it easier to remove your FLIPTREE®, it is
recommended to close the carton flaps and reposition the
tree carton flat on floor with arrows pointing upright.
Please note, the tree is packed with storage bag, the flip
stand is attached to the tree and should never be removed.
SECTION A
TREE BODY
SECTION B
MIDDLE SECTION
SECTION C
TREE TOP

Step 3
Before moving your FLIPTREE® make sure you have created a safe display location for your tree by removing
any items or furniture that may hit your tree during the flipping process. Using the green handle located near the
top of the main tree storage bag, tilt the tree back and slowly wheel it to its final display location. DO NOT
ATTACH TREE TOP TO MAIN BAG UNTIL THE TREE IS IN ITS FINAL STORAGE LOCATION.
Green Handle
Step 4
Press down the locking tabs on both front wheels once
the tree is in its desired location.
Locking Tabs
Step 5.
Remove the main tree storage bag. Unbuckle both cinch
straps located on the sides of the main bag. Then, unbuckle
the two stability straps at the bottom of the bag before
unzipping and removing the main bag. Unzip the tree top
and remove the bag.
Step 6.
Your FLIPTREE® requires one or two people to flip into
the display or storage position, anyone not assisting in
flipping your tree should stand at a safe distance. Young
children should not assist in flipping a FLIPTREE®.

Step 7.
With your foot on the footrest begin pulling the tree in the direction shown by the FLIPTREE® Indicator
(towards you and down to the center of the foot pedal). If you find it difficult to attach the tree top with
the tree in the full upright position you may choose to tilt the tree slightly for easier access.
Indicator

Step 8
Once you have finished flipping your tree, attach the
middle section B into body section A, insert tree top
section C into section B. Then plug light set of
section C into section B. Plug light set of section B
into power strip.
T OP SECTION C
(GREEN
PLUG)
MIDDLE SECTION B
(BLUE
PLUG)
R EMOTE CONTROL
and
P LUG-IN REMO TE
CONTROL RECEIVER
Wall Outlet
FLIP
B OTTOM SECTION A
(RED PLUG)
Step 9
Buckle the safety strap at the bottom of the tree.
Drawing not to Scale
Step 10
Plug the light set of tree body A into power strip. Plug power strip into the remote control receiver. Plug the
remote control received into wall outlet.

STORAGE TIPS
Step 1.
Unplug the cord connecting the tree lights to the
remote and wall socket.
Step 2.
Unplug the lights connecting the tree sections.
Step 3.
Remove the tree top and middle section and
place
both
in the tree top storage bag. If you find it diffi-
cult to remove the tree top sections in this
position
you may wish to unbuckle the safety latch and tilt the
tree slightly for easier access.
Step 4.
Check that front wheels are locked.
Step 5.
Unbuckle safety strap.
Step 6.
With your foot on the footrest begin pulling the tree
up and away from the foot pedal.
Step 7.
Place the main tree storage bag over the top of the
tree making sure the zipper is aligned with the center
of the footrest.
Step 8.
Gently pull the bag down over the tree until the bag
nearly touches the floor. Then zip up the bag.
Step 9.
Loop each of the stability straps at the bottom of the
main tree bag around the back base leg before
connecting buckle to the main bag.
Step 10.
Fasten the two cinch straps on both sides of the main
tree bag. Connect the green handle strap located near
the zipper of the main tree bag.
Step 11.
Unlock the front wheels, grab the green handle, tilt
the tree back, and proceed to wheel the tree to its final
storage location. DO NOT ATTACH TREE TOP TO
MAIN BAG UNTIL THE TREE IS IN ITS FINAL
STORAGE LOCATION.
Step 12.
To attach the tree top to the main bag, place the tree
top pole in the footrest hole and connect using the
straps found on the main bag.

CARE & MAINTENANCE INSTRUCTION
1. This is for decorative use only - do not immerse in water or expose to heat. Keep away from fire.
2. Please use water only for cleaning purpose.
3. When not in use, store neatly in a cool, dry location protected from sun light.
4. When the remote control has malfunctioned, please remove the power strip from the receiver and plug the power strip directly into
the wall.
THE FOLLOWINGSTEPS WILL HELPMAKE YOUR TREE LOOK MORE REALISTIC
1. Light tree one section at a time as described in assembly instructions, so you can easily identify any bulbs that may be dislodged.
Push any loose bulbs back into their sockets.
2. Separate the branch tips to form a “V” shape and fluff the needles. Make sure each tip is spread out and no two branches are
touching each other. For best access to branches, shape each section prior to adding the next section as described in the initial
assembly instructions. You may want to wear cotton gloves when fluffing needles to avoid scratches and skin irritation.
3. Starting with the bottom row, position the branches parallel to the floor. Angle the tips slightly upward like they are growing
towards the sun. With each successive row, make the upward angle of the branches more pronounced. Position inner tips to hide
the center of the tree.
4. Arrange the uppermost section of the tree so that the tips are evenly spaced and pointing upward.
5. Step back and review the tree. Adjust branches and tips as neccessary to give the tree a fuller appearance (The tree may be shape
differently (upswept /downswept /etc.) pending on one’s preference.)
TROUBLE SHOOTINGTIPS
1. If entire tree lighting does not light, make sure power strip cords are securely inserted in a working wall outlet.
2. If an entire section of the tree does not light, please review following actions:
a. Check that all plugs within the tree are securely connected.
b. Check fuse in power strip to determine if it may need replacement. Caution: Note that a blown fuse indicates an electrical
overload or electrical short circuit. If the fuse is blown, unplug power strip from outlet. Also unplug any additional strings
or products may be attached to the power strip. Replace the fuse following manufacturer instructions with proper fuse
rating. If the replacement fuse blows, a short circuit may be present and the product should be discarded.
c. Check fuse in plug connection on end of each light string.(See section on replacing plug fuses in this document).

TROUBLE SHOOTINGTIPS (Cont.)
3. If some individual lights do not light up, it may be due to becoming dislodged from the socket during assembly. Note those not
lit up; check for looseness and push any loose bulbs gently back into their socket. If they still do not light up, try a replacement
light bulb (supplied by manufacturer) and follow directions in section describing how to replace light bulbs.
IMPORTANT BASIC SAFETY INSTRUCTIONS
When using electrical products, to avoid risk of fire burns, personal injury and electrical shock, basic precautions should always be
followed as stated below:
READ AND
FOLLOW ALL SAFETY INSTRUCTIONS
1. Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor
applications, connect the product to a Ground Fault Circuit interrupting (GFCI) outlet. If one is not provided, contact a qualified
electrician for proper installation.
2. This seasonal use product is not intended for permanent installation or use.
3. Do not mount or place near gas or electrical heaters, fireplace, candles or other similar sources of heat.
4. Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
5. Do not let lamps rest on the supply cord or on any wire.
6. For your safety, unplug the product when leaving the house, when retiring for the night or if left unattended.
7. This is an electrical product – not a toy! To avoid risk of fire, burns, personal injury and electric shock it should not be played
with or placed where small children can reach
it.
8. Do not use this product for other than its intended use.
9. Do not hang ornaments or other objects from cord, wire or light string.
10.Do not close doors or windows on the product or extensions cords as this may damage the wire insulation.
11. Do not cover the product with cloth, paper or any material not part of the product when in use.
12. This product is equipped with push-in lamps. Do not twist the lamps.
13. This product employs overload protection (fuse). Ablown fuse indicates an overload or short-circuit situation. If the fuse blows,
unplug the product from the outlet. Also unplug any additional strings or products that may be attached to the product. Replace
the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the
replacement fuse blows, a short-circuit may be present and the product should be discarded.
14. Read and follow all instructions that are on the product or provided with the product.
CAUTION: To reduce the risk of fire and electric shock:
a. Do not install on trees having needles, leaves or branch coverings of metal or materials which look like metal, and:
b. Do not mount or support strings in a manner that can cut or damage wire insulation.

USER INSTRUCTIONS
TO REPLACE LIGHT BULBS
CAUTION: FIRST UNPLUG YOUR PRODUCT FROM ANY POWER SOURCE.
1.
T o reduce th e risk of overheating,replace burned-out light bulbs promptly .Use only
2.5 volt light bulbs only.
2. Grasp plug and remove from the receptacle or any other electrical outlet device. Do
not
unplug by pulling on the cord.
3. Pull the light bulb
and its attached plastic base straight out of light bulb holder.
4. Replace light bulb with only 2.5 volt
super bright type light (provided with product).
PULL BULB UP
TOREMOVE
t
i PUS H BULB DOWN
.... TOREPLACE
5.
If the new lamp base does not fit th e replacement light bulb, follow the steps below
before step
4.
a. Remove the base of burned out light by
straightenin g light leads and gently pull bulb out.
b.Thread metal leads of new lamp through hose in old base with one lead in each hold.
c. After lamp is fully inserted into base , bend each lead up, like other lights in the light set so that the leads will touch the
contacts inside
th e light socket.
TOREPLACE A FUSE:
CAUTION: FIRST UNPLUGYOUR PRODUCT FRO M ANY POWER SOURCE.
1. Grasp plug and remove from the receptacle or other outlet device.Do not unplug
by
pulling on cord.
2. Open fuse cover. Slide openfuse access cover on top of attachment plugtowards
plug's
metal prongs or blades.
3. Remove fuse carefully.
4. Risk of fire.Replace fuse
ONL Ywith 3 Amp 120 Volt fuse. (Provided with product).
5. Close fuse cover.Return the sliding fuse cover
back to its former closed position on
attachment plug.
6. Risk of fire.Do not replace attachment plug becauseit contains
a safety device ( fuse )
that should not be removed.
Discardproduct if the attachment plug is damaged
FUSECOVER
SLIDES FORWARD
Please contact one of our
Product Specialists for assembly assistance or questions at 1-800-537-8484 or email [e-mail].
Specialists are available weekdays 8:00 a.m.to
8:00p.m.EST or Saturday 9:30 a.m. to 6:00 p.m.