FrSky SMART PORT Airspeed ASS70 ADV User manual

PORT
Version
1.0
FrSky Electronic Co., Ltd. www.frsky-rc.com Contact us : [email protected]
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
Instruction Manual for FrSky
Airspeed Sensor— ASS70/ASS100 ADV
Thank you for purchasing FrSky Smart Port AirSpeed Sensor ASS70/ASS100 ADV. It is designed for FrSky
SmartPort enabled system, and can provide AirSpeed data for your entire flight. In order to fully enjoy the benefit
of it, please read the instruction manual carefully and set up the device as described below.
Introduction
Following the steps to finish the setting procedures:
1. Assembled pitot tube with the circuit board into an AirSpeed Sensor, as shown in figure.
Notice: Avoid any loose tubing.
2. The static holes on the pitot tube (As Figure) should extend at least 13mm past the wing’s leading edge, or past
any other obstructions - the farther out, the better. This is to ensure the static holes and pitot pickup are in
undisturbed air.
3. For planes, it’s important that the tube should be placed properly so that it is not directly in the plane’s prop-wash,
which will result in erroneous readings. The best place to install the tube is on the leading edge of the wing several
inches out from the fuselage, as shown in Figure.
4. Connect the sensor to receiver Smart Port.
Set up
Note: All instructions, warranties and other collateral documents are subject to change at the sole
discretion of FrSky Electronic Co., Ltd. For further information, please visit www.frsky-rc.com
and click the support tab for this product.
ASS70 ADV:
●
Operational Voltage: DC 4 -10 V
● Current consumption: 20mA@5V
● Measure airspeed range: 0~270km/h (0~167.7mile/h )
● Circuit Board: Weight 6.3 g, dimensions 33*22*10.16mm (L*W*H)
● Pitot Tube: Weight 4.4 g, length 101mm, diameter 2.6 mm
● Pitot Tube Hose: Silicon, clear, 3 feet (1 meter), 2.2mm ID, 4mm OD
● Compatible with FBUS/S.Port protocol
ASS100 ADV:
●
Operational Voltage: DC 4 -10 V
● Current consumption: 10mA@5V
● Measure airspeed range: 0~360km/h (0~223.7mile/h )
● Circuit Board: Weight 4.9g, dimensions 30*20*10.45 mm (L*W*H)
● Pitot Tube: Weight 4.4g, length 101mm, diameter 2.6 mm
● Pitot Tube Hose: Clear silicon tubing, 3 feet (1 meter), 2mm ID, 4mm OD
● Compatible with FBUS/S.Port protocol
Specifications
Overview
20 mm
30 mm
22 mm
33 mm

FrSky is continuously adding features and improvements to our products. To get the most from your product, please check
the download section of the FrSky website www.frsky-rc.com for the latest update firmware and manuals.
*Install FrSky Smart Port AirSpeed Sensor ASS70/ASS100 ADV on any appropriate surface of the
airframe that stays away from water, vibration, or fuel.
Each type of FrSky Smart Port enabled sensor has its unique physical ID. The ID number could be changed by
FreeLink.
ID Set up
*All FrSky Smart Port enabled sensors could daisy chain with each other through their Smart Port.
PORT
Version
1.0
FrSky Electronic Co., Ltd. www.frsky-rc.com Contact us : [email protected]
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
Instruction Manual for FrSky
Airspeed Sensor— ASS70/ASS100 ADV
Leading Edge
of Wing
Static Holes
Static Port
Pressure Port
To the FrSKy receiversTo other FrSKy FBUS/S.Port
Enabled Sensor
ASS70/ASS100 ADV
13
mm
LED Status
FBUS
NO
YES
LED Status
Flash slowly
Flash quickly
S.Port
YES
NO