FrSky ACCESS XM User manual

Registration & Automatic binding (Smart Match )
With the FrSky ACCESS protocol, the transmitter/transmitter module can bind receiver without using the "F/S"
button.
Follow the step below to finish the Registration & binding procedure:
1. Put the transmitter/transmitter module into [Reg] status.
1.1 For Taranis X-Lite Pro as an example, turn on the transmitter, go to the MENU-MODEL SETUP-PAGE 2,
choose Internal or External RF, and select [Reg].
2. Connect the battery to the receiver while holding the F/S button on the receiver. The RED LED and GREEN LED
on the receiver will be on, indicating into the [Reg] status. Select [ENTER] on the transmitter, The RED LED and
GREEN LED will flash, and the transmitter displays [Registration ok].
3. Turn off the receiver.
4. Move the cursor to select the receiver 1 [Bind].
5. Connect the battery to the receiver, the GREEN LED will flash, indicating into the [Bind] status. Select the RX,
the GREEN will keep lit, and the transmitter displays [Bind successful].
6. The transmitter exit [Bind], GREEN LED will keep lit, RED LED will be off, indicating Working normally.
TM
Failsafe
Failsafe is a useful feature which is for a preset channel output position whenever control signal is lost for a period.
Follow the steps to set Failsafe for channels necessary:
Failsafe for receiver supporting ACCESS can be set via radio interface, which support no pulse, hold and custom
three modes for each channel.
1. For Taranis X-Lite Pro as an example, turn on the transmitter, go to: MODEL SETUP/Internal RF/Failsafe.
2. Failsafe can be set on receiver via short pressing F/S button while moving a certain channel position to a preset
value after binding.
Much more operation and instruction please refer to radio manual.
For more details, please check the complete manual for XM from www.frsky-rc.com - Download - Manual.
Should you have other questions, please send e-mails to FrSky technical support [email protected].
Overview
F/S
Specifications
• Dimension: 15*10*3.5mm (L x W x H)
• Weight: 1g
• Number of Channels: Up to 16CH from SBUS
(Default 16 channel, press the button ＞5s, Ch16 will switch
between RSSI and channel output.)
• Operating Voltage Range: 3.5V~10V
• Operating Current: 20mA@5V
• Operating Range: ＞600m
• With RSSI output on board: Analog 0~3.3V
• Firmware Upgradeable
• Compatibility: TX With ACCESS V1.1.2
FrSky Electronic Co., Ltd. www.frsky-rc.com Contact us: [email protected]
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
01140049
Version
1.0
Instruction Manual for FrSky ACCESS XM
FrSky is continuously adding features and improvements to our products. To get the most from your product, please check
the download section of the FrSky website www.frsky-rc.com for the latest update firmware and manuals

Registration & Automatic binding (Smart Match )
With the FrSky ACCESS protocol, the transmitter/transmitter module can bind receiver without using the "F/S"
button.
Follow the step below to finish the Registration & binding procedure:
1. Put the transmitter/transmitter module into [Reg] status.
1.1 For Taranis X-Lite Pro as an example, turn on the transmitter, go to the MENU-MODEL SETUP-PAGE 2,
choose Internal or External RF, and select [Reg].
2. Connect the battery to the receiver while holding the F/S button on the receiver. The RED LED and GREEN LED
on the receiver will be on, indicating into the [Reg] status. Select [ENTER] on the transmitter, The RED LED and
GREEN LED will flash, and the transmitter displays [Registration ok].
3. Turn off the receiver.
4. Move the cursor to select the receiver 1 [Bind].
5. Connect the battery to the receiver, the GREEN LED will flash, indicating into the [Bind] status. Select the RX,
the GREEN will keep lit, and the transmitter displays [Bind successful].
6. The transmitter exit [Bind], GREEN LED will keep lit, RED LED will be off, indicating Working normally.
TM
Failsafe
Failsafe is a useful feature which is for a preset channel output position whenever control signal is lost for a period.
Follow the steps to set Failsafe for channels necessary:
Failsafe for receiver supporting ACCESS can be set via radio interface, which support no pulse, hold and custom
three modes for each channel.
1. For Taranis X-Lite Pro as an example, turn on the transmitter, go to: MODEL SETUP/Internal RF/Failsafe.
2. Failsafe can be set on receiver via short pressing F/S button while moving a certain channel position to a preset
value after binding.
Much more operation and instruction please refer to radio manual.
For more details, please check the complete manual for XM+ from www.frsky-rc.com - Download - Manual.
Should you have other questions, please send e-mails to FrSky technical support [email protected].
Overview
F/S
Specifications
• Dimension: 21.5*12*3.5mm (L x W x H)
• Weight: 1.6g
•
Number of Channels: Up to 16CH from SBUS (Default 16 channel, press the button ＞5s, Ch16 will switch
between RSSI and channel output.)
• Operating Voltage Range: 3.5V~10V
• Operating Current: 30mA@5V
• Operating Range: Full range
• With RSSI output on board: Analog 0~3.3V
• Firmware Upgradeable
• Compatibility: TX With ACCESS V1.1.2
FrSky Electronic Co., Ltd. www.frsky-rc.com Contact us: [email protected]
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
01140049
Version
1.0
Instruction Manual for FrSky ACCESS XM+
FrSky is continuously adding features and improvements to our products. To get the most from your product, please check
the download section of the FrSky website www.frsky-rc.com for the latest update firmware and manuals