FrSky ARCHER R8 PRO User manual

Instruction Manual for FrSky ARCHER GR8 Receiver
Version
1.0
Registration & Automatic binding (Smart Match )
With the FrSky ACCESS protocol, the transmitter/transmitter module can bind receiver without using the "REG"
button.
Follow the step below to finish the Registration & binding procedure:
1. Put the transmitter/transmitter module into [Reg] status.
1.1 For Taranis X-Lite Pro as an example, turn on the transmitter, go to the MENU-MODEL SETUP-PAGE 2,
choose Internal or External RF, and select [Reg].
TM
Introduction
LED state
Green LED
On
Flash
On
On
On
Off
Red LED
On
Flash
On
Off
Off
On
Status
Register
Register successfully
Bind
Bind successfully
Working normally
Failsafe
Specifications
● Dimension: 47*26*15mm (L*W*H)
● Weight: 13g
● Number of Channels: 16/24 SBUS Channels
- 16 SBUS channels
- 24 SBUS channels (Stay tuned)
● Operating Voltage Range: 3.5-10V
● Operating Current: ＜55mA@5V
● Control Range: Full range* with telemetry
(*Full Range: ＞2km, range may vary based
on local conditions.)
● Voltage Measurement Range via AIN2
(External device): 0-36V
(Battery Voltage Division Ratio: 1:10）
● Compatibility: All FrSky ACCESS transmitters
Version
1.0
Instruction Manual for FrSky ARCHER R8 PRO Receiver
FrSky Electronic Co., Ltd. www.frsky-rc.com Contact us : [email protected]
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
01140165
The Archer R8 PRO has 8 high-precision PWM channel outputs and features excellent Anti-interference
performance when it comes to spark-ignition on internal combustion models. It supports full-range signal strength
with dual detachable antennas that assure optimal antenna reception and maximum range. In addition to all this, the
R8 Pro can also be used as a redundancy receiver along with any other FrSky ACCESS capable receiver equipped
with a SBUS port.
All of the Archer receivers are hyper-matched with the ACCESS protocol. They not only feature wireless firmware
upgrades, increased range, and telemetry performance, the R8 PRO now supports more functions like configurable
telemetry power, S.Port/F.Port switching and FLR output. Additional valuable features are under development to
unlock the true potential of the ACCESS protocol.
Features
● ACCESS Protocol with Over The Air (OTA)
● Receiver redundancy
● 8 high-precision PWM channels
● SBUS IN &OUT (using standard servo connectors)
● S.Port / F.Port and AIN2 (on 4 pin socket)
● VFR (Valid Frame Rate) telemetry
● Anti-interference in spark-ignition
Overview
2
8/24CH Telemetry
R8 PRO
BUTTON

FrSky is continuously adding features and improvements to our products. To get the most from your product, please check
the download section of the FrSky website www.frsky-rc.com for the latest update firmware and manuals
2. Connect the battery to the receiver while holding the button on the receiver. The RED LED and GREEN LED on
the receiver will be on, indicating into the [Reg] status. Select [ENTER] on the transmitter, The RED LED and
GREEN LED on the receiver will flash, and the transmitter displays [Registration ok].
3. Turn off the receiver.
4. Move the cursor to select the receiver 1 [Bind].
5. Connect the battery to the receiver, the GREEN LED will flash, indicating into the [Bind] status. Select the RX, the
GREEN will keep lit, and the transmitter displays [Bind successful].
6. The transmitter exit [Bind], GREEN LED will keep lit, RED LED will be off, indicating Working normally.
Version
1.0
Instruction Manual for FrSky ARCHER R8 PRO Receiver
FrSky Electronic Co., Ltd. www.frsky-rc.com Contact us : [email protected]
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
01140165
Note: The SBUS output is 7ms, no matter HS/FS mode.
Warning: HS mode is only applied for digital servos. Other servos should select FS mode, otherwise
servos will get hot and may burn out.
How to Switch FS (20ms) mode/HS (7ms) mode
a) The factory default setting is FS mode.
b) To go to the receiver [Options], select the 7ms PWM or not.
Warning: [Options ] setting in flight will cause the failsafe.
FCC STATEMENT
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
About OTA function
-- For Taranis X-Lite Pro as an example, go to the SD CARD 2/7, and select the FW, press the enter button, select
[Flash receiver OTA], power on the receiver, select the RX, go to the [ENTER], complete the flash process, the
transmitter will display [Flash successful]. Re-power the receiver and wait for 3 seconds, the Green LED starts
flashing indicates the receiver works properly at the momemnt.
Note: Please do not do the binding operation in the near range while the firmware upgrading in progress.
Note: Update the firmware after the receiver gets bound.