FS AP-W6D2400C User manual

AP-W6D2400C/AP-W6T6817C
ENTERPRISE WI-FI 6 ACCESS POINT
Quick Start Guide

Introduction
Thank you for choosing the enterprise Wi-Fi 6 access point. This guide is designed to familiarize you
with the layout of the access point and describes how to deploy the access point in your network.
AP-W6D2400C AP-W6T6817C
Accessories
AP-W6D2400C
Mounting Bracket x1
Power Cord x1 Power Injector x1 Screw Anchor x2Screw x2
POWER
ACTIVE
UPUP

AP-W6T6817C
Power Injector x1
Mounting Bracket x1 Hidden Lock’s Key x1
Screw Anchor x4Screw x4Power Cord x1
Optional (Not Included)
POWER
ACTIVE
UP UP
K K

Hardware Overview
Ports
AP-W6D2400C
Ports
Description
LAN/PoE
LAN/PoE port
Console
An RJ45 console port for serial management
Power
48V DC power port
AP-W6T6817C
Console Power
LAN/PoE
Security Lock
k
USB
Console
LAN3/IoT
Power
LAN1/PoE
LAN2

Button
Description
Reset
Restart: Press the Reset button for less than three seconds.
Restore to Factory Default Settings: Press and hold the Reset button
for more than three seconds.
Ports
Description
LAN1/PoE
LAN1/PoE port, PoE+ capable
LAN2
LAN2 port
LAN3/IoT
LAN3/IoT port
Security Lock
Anti-theft lock hole
Console
An RJ45 console port for serial management
USB
A USB management port for software and configuration backup
and ofline software upgrade
Power
48V DC power port
Button
AP-W6D2400C/AP-W6T6817C
Reset Reset

LED
AP-W6D2400C/AP-W6T6817C
FIT AP:
Status
Frequency
Description
Ou
N/A
The AP is not receiving power, or the AP is
in Do Not Disturb mode, which can be
disabled by software.
Blinking Green
3Hz
UBoot program initialization in progress.
Solid Green
N/A
Main program initialization in progress.
Blinking Red
3Hz
Initialization is complete, but the Ethernet
link is down.
2Hz
Locates the AP-W6D2400C.
Double Blinking Red
3Hz (on and ou for
2 cycles alternately)
Locates the AP-W6T6817C.
Solid Orange
N/A
Initialization is complete, and the AP is
establishing a CAPWAP connection with
a wireless LAN controller.
Blinking Orange
3Hz
Firmware upgrade in progress. Do not
power ou.
Solid Blue
N/A
Normal operation, but no wireless clients
are associated with the AP.
Blinking Blue
3Hz
Normal operation, at least one wireless
client is associated with the AP.
LED LED
k

Status
Frequency
Description
Ou
N/A
The AP is not receiving power, or the
AP is in Do Not Disturb mode, which
can be disabled by software.
Blinking Green
3Hz
UBoot program initialization in progress.
Solid Green
N/A
Main program initialization in progress.
Blinking Red
3Hz
Initialization is complete, but the Ethernet
link is down.
Solid Blue
N/A
Normal operation, but no wireless clients
are associated with the AP.
Blinking Blue
3Hz
Normal operation, at least one wireless
client is associated with the AP.
FAT AP:
NOTE: Hz indicates the number of times a flashing light blinks per second.
Installation Requirements
Install the AP indoors.
Make sure the floor of the installation site is dry and flat.
Place the AP in a dry area and avoid liquid intrusion.
Keep the AP and installation tools away from walkways.
Do not power the AP during installation.
Install the AP in a well-ventilated location.
Keep away from high voltage cables.
Keep the AP clean and dust-free.

Mounting the Access Point
Ceiling Mount
AP-W6D2400C
1.Position the mounting bracket at the desired location on the ceiling. Use a marker to mark the two
mounting holes.
2. Drill holes with a diameter of 6 mm (0.24 in) in the marked locations.
3. Insert a screw anchor into each hole, and tap the screw anchor with a rubber hammer.

4. Secure the mounting bracket to the ceiling by inserting the screws into the anchors.
5. Align the tabs on the AP bracket into the notches on the ceiling bracket, and then slide the AP until
it snaps into place.

NOTE:
1. Before mounting the AP on the bracket, you must first install the Ethernet cables.
2.The tabs should fit easily into the mounting slots. Do not forcibly push the AP into the
slots.
3. After installation, verify that the AP is securely fastened.
4. The wall mount installation is the same as the ceiling mount.
(Optional) Securing the AP
AP-W6T6817C
1. Remove the screw on the mounting bracket and engage the hidden lock.
2. Align the tabs on the AP bracket into the notches on the bracket, and then slide the AP until it
snaps into place.