FS AP Series User manual

ENTERPRISE WI-FI 6 ACCESS POINT
Quick Start Guide

Introduction
Accessories
Thank you for choosing the enterprise Wi-Fi 6 access point. This guide is designed to familiarize you
with the layout of the access point and describes how to deploy the access point in your network.
AP-W6D2400C AP-W6T3267C/AP-W6Q4134C
AP-W6T6817C/AP-W6T10000C
AP-W6D2400C
Mounting Bracket x1
Power Cord x1 Power Injector x1 Screw Anchor x2Screw x2
POWER
ACTIVE
UPUP

AP-W6T3267C/AP-W6Q4134C/AP-W6T6817C/AP-W6T10000C
Power Injector x1
Hidden Lock’s Key x1
Screw Anchor x4Screw x4Power Cord x1
Optional (Not Included)
POWER
ACTIVE
Mounting Bracket x1
UP UP
K K

Hardware Overview
Ports
AP-W6D2400C
Console
LAN/PoE
Power
AP-W6Q4134C
Security Lock
k
USB
Console
LAN1/2.5G/PoE
LAN2/IoT
Power
AP-W6T3267C/AP-W6T6817C
Security Lock
k
USB
Console
LAN3/IoT
LAN2
LAN1/PoE
Power

AP-W6T10000C
Ports Description
LAN2
LAN3/IoT
LAN2/HPoE
LAN1/2.5G/PoE
LAN2 port
LAN3/IoT port
LAN2/IoT LAN2/IoT port
LAN2/HPoE port
LAN1/2.5G/PoE port
LAN1/PoE
LAN/PoE
Security Lock
Console
USB
Power
LAN1/PoE port
LAN1/HPoE LAN1/HPoE port
LAN/PoE port
Anti-theft lock hole
An RJ45 console port for serial management
A USB management port for software and conguration backup
and oine software upgrade
48V DC power port
Power
LAN1/HPoE
LAN2/HPoE
LAN3/IoT
Console
USB
Security Lock

Reset
Button
AP-W6D2400C
AP-W6T10000C
AP-W6T3267C/AP-W6Q4134C/AP-W6T6817C
Reset
Reset

LEDs
Button Description
Reset Restore to Factory Default Settings: Press and hold the Reset button
for more than three seconds.
Restart: Press the Reset button for less than three seconds.
AP-W6D2400C
AP-W6T3267C/AP-W6Q4134C/AP-W6T6817C/AP-W6T10000C
LED
k
LED

FIT AP:
DescriptionStatus
O
Blinking Green
Frequency
N/A
3Hz
N/A
1.5Hz
2Hz
The AP is not receiving power, or the AP is
in Do Not Disturb mode, which can be
disabled by software.
3Hz (on and o for
2 cycles alternately)
N/A
UBoot program initialization in progress.
Main program initialization in progress.
Initialization is complete, but the Ethernet
link is down.
Locates the AP-W6D2400C.
Locates the AP-W6T3267C/AP-W6Q4134C
AP-W6T6817C/AP-W6T10000C.
Initialization is complete, and the AP is
establishing a CAPWAP connection with
a wireless LAN controller.
Firmware upgrade in progress. Do not
power o.
Normal operation, but no wireless clients
are associated with the AP.
Normal operation, at least one wireless
client is associated with the AP.
3Hz
N/A
1.5Hz
Solid Green
Blinking Red
Double Blinking Red
Solid Orange
Blinking Orange
Solid Blue
Blinking Blue

FAT AP:
DescriptionStatus
O
Blinking Green
Frequency
N/A
3Hz
N/A
1.5Hz
The AP is not receiving power, or the
AP is in Do Not Disturb mode, which
can be disabled by software.
UBoot program initialization in progress.
Main program initialization in progress.
Initialization is complete, but the Ethernet
link is down.
Solid Green
Blinking Red
Solid Blue
1.5Hz Normal operation, at least one wireless
client is associated with the AP.
Blinking Blue
N/A
Normal operation, but no wireless clients
are associated with the AP.
NOTE: Hz indicates the number of times a ashing light blinks per second.
Installation Requirements
Install the AP indoors.
Make sure the oor of the installation site is dry and at.
Place the AP in a dry area and avoid liquid intrusion.
Keep the AP and installation tools away from walkways.
Do not power the AP during installation.
Install the AP in a well-ventilated location.
Keep away from high voltage cables.
Keep the AP clean and dust-free.

AP-W6D2400C
Mounting the Access Point
Ceiling Mount
1. Position the mounting bracket at the desired location on the ceiling. Use a marker to mark the two
mounting holes.
2. Drill holes with a diameter of 6 mm (0.24 in) in the marked locations.
3. Insert a screw anchor into each hole, and tap the screw anchor with a rubber hammer.