FSP Technology 10K User manual

3/3 10K~30K Online UPS
Uninterruptible Power Supply System
Version: 1.1
User Manual

4
2. Installation and Operation
There are two different types of online UPS: standard and long-run models. Please refer to the following
model table.
Model
Type
Model
Type
10K
Standard
model
10KL
Long-run
model
15K
15KL
20K
20KL
30K
30KL
We also offer optional parallel function for these two types by request. The UPS with parallel function is
called as “Parallel model”. We have described detailed installation and operation of Parallel Model in the
following chapter.
2-1. Unpacking and Inspection
Unpack the package and check the package contents. The shipping package contains:
● One UPS
●One user manual
● One monitoring software CD
●One RS-232 cable (option)
●One USB cable
●One parallel cable (only available for parallel model)
●One share current cable (only available for parallel model)
NOTE: Before installation, please inspect the unit. Be sure that nothing inside the package is damaged
during transportation. Do not turn on the unit and notify the carrier and dealer immediately if there is any
damage or lacking of some parts. Please keep the original package in a safe place for future use.

5
2-2. Rear Panel View
Diagram 1: 10K(L)/15K(L)/20K(L) Diagram 2: 30KL Rear Panel Diagram 3: 30K Rear Panel
Rear Panel
Diagram 4: Rack Rear Panel Diagram 5: Rack
Input/Output Terminal

6
Diagram 6: 10K(L)15K(L)/20K(L) Diagram 7: 30K(L)
Input/Output Terminal Input/Output Terminal
1. RS-232 communication port
2. USB communication port
3. Emergency power off function connector (EPO connector)
4. Share current port (only available for parallel model)
5. Parallel port (only available for parallel model)
6. Intelligent slot
7. Power stage fan
8. External battery connector (Only available for long-run model)
9. Bypass Input Circuit Breaker(Only available for dual input unit)
10. Input/Output terminal (Refer to Diagram 5, 6 and 7)
11. Line Input circuit breaker
12. Maintenance bypass switch
13. Output Grounding terminal
14. Output terminal: connect to mission-critical loads
15. Line input terminal
16. Bypass input terminal(Only available for dual input)
17. Input Grounding terminal
18. External maintenance bypass switch port
2-3. Single UPS Installation
Installation and wiring must be performed in accordance with the local electric laws/regulations and execute
the following instructions by professional personnel.
1) Make sure the mains wire and breakers in the building are enough for the rated capacity of UPS to
avoid the hazards of electric shock or fire.
NOTE: Do not use the wall receptacle as the input power source for the UPS, as its rated current is less than
the UPS’s maximum input current. Otherwise the receptacle may be burned and destroyed.
2) Switch off the mains switch in the building before installation.
3) Turn off all the connected devices before connecting to the UPS.
4) Prepare wires based on the following table:

7
Model
Wiring spec (AWG)
Input(Ph)
Output(Ph)
Neutral
Battery
Ground
10K
10
10
8
8
10KL/10KR
10
10
8
8
8
15K
8
8
6
6
15KL/15KR
8
8
6
6
6
20K
8
8
6
6
20KL/20KR
8
8
6
6
6
30K
8
8
4
4
30KL
8
8
4
4
4
NOTE 1: The cable for 10K/10KL/10KR should be able to withstand over 40A current. It is
recommended to use AWG 10 or thicker wire for Phase and AWG 8 or thicker wire for Neutral for
safety and efficiency.
NOTE 2: The cable for 15K/15KL/15KR should be able to withstand over 63A current. It is
recommended to use AWG 8 or thicker wire for Phase and AWG 6 or thicker wire for Neutral for safety
and efficiency.
NOTE 3: The cable for 20K/20KL/20KR should be able to withstand over 63A current. It is
recommended to use AWG 8 or thicker wire for Phase and AWG 6 or thicker wire for Neutral for safety
and efficiency.
NOTE 4: The cable for 30K/30KL should be able to withstand over 63A current. It is recommended to
use AWG 8 or thicker wire for Phase and AWG 4 or thicker wire for Neutral for safety and efficiency.
NOTE 5: The selections for color of wires should be followed by the local electrical laws and
regulations.
5) Remove the terminal block cover on the rear panel of UPS. Then connect the wires according to the
following terminal block diagrams: (Connect the earth wire first when making wire connection. Disconnect
the earth wire last when making wire disconnection!)
Terminal Block wiring diagram of 10K(L)/15K(L)/20K(L)

8
Terminal Block wiring diagram of 30K(L)
Output Input
Terminal Block wiring diagram of Rack
For dual input unit, if there is two separate input, connect the Line input and bypass input respectively; if the
is only one common input, please connect the line input and bypass input together.
NOTE 1: Make sure that the wires are connected tightly with the terminals.
NOTE 2: Please install the output breaker between the output terminal and the load, and the breaker
should be qualified with leakage current protective function if necessary.
6) Put the terminal block cover back to the rear panel of the UPS.
Warning: (Only for standard model)
● Make sure the UPS is not turned on before installation. The UPS should not be turned on during wiring
connection.
● Do not try to modify the standard model to the long-run model. Particularly, do not try to connect the
standard internal battery to the external battery. The battery type and voltage may be different. If you
connect them together, it maybe causes the hazard of electric shock or fire!
Warning: (Only for long-run model)
● Make sure a DC breaker or other protection device between UPS and external battery pack is installed. If
not, please install it carefully. Switch off the battery breaker before installation.
NOTE: Set the battery pack breaker in “OFF” position and then install the battery pack.
● Pay highly attention to the rated battery voltage marked on the rear panel. If you want to change the
numbers of the battery pack, please make sure you modify the setting simultaneously. The connection
with wrong battery voltage may cause permanent damage of the UPS. Make sure the voltage of the

9
battery pack is correct.
● Pay highly attention to the polarity marking on external battery terminal block, and make sure the
correct battery polarity is connected. Wrong connection may cause permanent damage of the UPS.
● Make sure the protective earth ground wiring is correct. The wire current spec, color, position,
connection and conductance reliability should be checked carefully.
● Make sure the utility input & output wiring is correct. The wire current spec, color, position, connection
and conductance reliability should be checked carefully. Make sure the L/N site is correct, not reverse
and short-circuited.
2-4. UPS Installation for Parallel System
If the UPS is only available for single operation, you may skip this section to the next.
1) Install and wires the UPSs according to the section 2-3.
2) Connect the output wires of each UPS to an output breaker.
3) Connect all output breakers to a major output breaker. Then this major output breaker will directly
connect to the loads.
4) Each UPS is connected to an independent battery pack.
NOTE: The parallel system can not use one battery pack. Otherwise, it will cause system permanent failure.
5) Refer to the following wiring diagram:
Wiring diagram of parallel system for 10K(L)/15K(L)/20K(L)

10
Wiring diagram of parallel system for 30K(L)
Wiring diagram of parallel system for Rack
2-5. Software Installation
For optimal computer system protection, install UPS monitoring software to fully configure UPS shutdown.

34
6. Specifications
Tower UPS
MODEL
10K
10KL
15K
15KL
20K
20KL
30K
30KL
CAPACITY
10000VA / 9000W
15000VA / 13500W
20000VA / 18000W
30000VA / 27000W
INPUT
Voltage
Range
Low Line Loss
110 VAC(Ph-N) ± 3 % at 50% Load
176 VAC(Ph-N) ± 3 % at 100% Load
Low Line Comeback
Low Line Loss Voltage + 10V
High Line Loss
300 VAC(L-N) ± 3 % at 50% Load
276 VAC(L-N) ± 3 % at 100% Load
High Line Comeback
High Line Loss Voltage - 10V
Frequency Range
46Hz ~ 54 Hz @ 50Hz system
56Hz ~ 64 Hz @ 60Hz system
Phase
Three phase with Neutral
Power Factor
≧0.99 at 100% Load
OUTPUT
Phase
Three Phase with Neutral
Output voltage
3 x 400 VAC (3Ph+N)
AC Voltage Regulation
± 1%
Frequency Range
(Synchronized Range)
46Hz ~ 54 Hz @ 50Hz system
56Hz ~ 64 Hz @ 60Hz system
Frequency Range (Batt. Mode)
50 Hz ± 0.1 Hz or 60Hz ± 0.1 Hz
Overload
AC mode
100%~110%: 10min
110%~130%: 1min
>130% : 1sec
Battery mode
100%~110%: 30sec
110%~130%: 10sec
>130% : 1sec
Current Crest Ratio
3:1 max
Harmonic Distortion
≦2 % @ 100% Linear Load; ≦5 % @ 100% Non-linear Load
Transfer
Time
Line Battery
0 ms
Inverter Bypass
0 ms (When phase lock fails, <4ms interruption occurs from inverter to bypass)
Inverter ECO
<10 ms
EFFICIENCY
AC mode
> 89%
>89%
>89%
>90%
Battery Mode
> 86%
>88%
>87%
>89%
BATTERY
Standard
Model
Type
12 V / 9 Ah
12 V / 9 Ah
12 V / 9 Ah
12 V / 9 Ah
Numbers
20(18-20 adjustable)
2 x 20(18-20
adjustable)
2 x 20(18-20
adjustable)
3 x 20(18-20
adjustable)
Recharge Time
9 hours recover to 90% capacity
Charging Current
1.0 A ± 10% (max.)
2.0 A ± 10% (max.)
2.0 A ± 10% (max.)
4.0 A ± 10% (max.)
Charging Voltage
273 VDC ± 1%
Long-run
Model
Type
Depending on applications
Numbers
18 - 20
Charging Current
4.0 A ± 10% (max.)
4.0 A ± 10% (max.)
4.0 A ± 10% (max.)
12.0 A ± 10% (max.)
Charging Voltage
273 VDC ± 1%
PHYSICAL
Dimension, D X W X H (mm)
815X250
X826
592X250
X826
815X250
X826
592X250
X826
815X250
X826
592X250
X826
815 X 300
X 1000
815X250
X 826
Net Weight (kgs)
109
38
164
40
164
40
233.5
64
ENVIRONMENT
Operation Temperature
0 ~ 40°C (the battery life will down when > 25°C)
Operation Humidity
<95 % and non-condensing
Operation Altitude*
<1000m
Acoustic Noise Level
Less than 60dB @
1 Meter
Less than 65dB @ 1 Meter
MANAGEMENT
Smart RS-232 or USB
Supports Windows® 2000/2003/XP/Vista/2008, Windows® 7, Linux, Unix, and MAC
Optional SNMP
Power management from SNMP manager and web browser
*If the UPS is installed or used in a place where the altitude is above than 1000m, the output power must be derated one percent per 100m.
**Product specifications are subject to change without further notice.

35
Rack UPS
MODEL
10KR
15KR
20KR
CAPACITY
10000VA / 8000W
15000VA / 12000W
20000VA / 16000W
INPUT
Nominal Voltage
3 x 400 VAC (3Ph+N)
Voltage Range
190-520 VAC (3-phase) @ 50% load
305-478 VAC (3-phase) @ 100% load
Frequency Range
46Hz ~ 54 Hz @ 50Hz system
56Hz ~ 64 Hz @ 60Hz system
Phase
Three phase with Neutral
Power Factor
≧0.99 at 100% Load
OUTPUT
Phase
Three Phase with Neutral
Output voltage
3 x 400 VAC (3Ph+N)
AC Voltage Regulation
± 1%
Frequency Range
(Synchronized Range)
46Hz ~ 54 Hz @ 50Hz system
56Hz ~ 64 Hz @ 60Hz system
Frequency Range (Batt. Mode)
50 Hz ± 0.1 Hz or 60Hz ± 0.1 Hz
Current Crest Ratio
3:1 max
Harmonic Distortion
≦2 % @ 100% Linear Load; ≦5 % @ 100% Non-linear Load
Transfer
Time
Line Battery
0 ms
Inverter Bypass
0 ms (When phase lock fails, <4ms interruption occurs from inverter to bypass)
EFFICIENCY
AC Mode
90.5%
91%
91.3%
ECO Mode
96%
Battery Mode
86%
87%
88%
BATTERY
Standard
Model
Type
12 V / 9 Ah
12 V / 9 Ah
12 V / 9 Ah
Numbers
20(18-20 adjustable)
2 x 20(18-20 adjustable)
2 x 20(18-20 adjustable)
Recharge Time
9 hours recover to 90% capacity
Charging Current
1.0 A ± 10% (max.)
2.0 A ± 10% (max.)
2.0 A ± 10% (max.)
Charging Voltage
273 VDC ± 1%
Long-run
Model
Type
Depending on applications
Numbers
18 - 20
Charging Current
4.0 A ± 10% (max.)
4.0 A ± 10% (max.)
4.0 A ± 10% (max.)
Charging Voltage
273 VDC ± 1%
PHYSICAL
Standard
Model
Dimension, D X W X H
mm
UPS: 668 x 438 x 266[6U]
Battery pack : 580 x 438 x
133[3U]
UPS: 668 x 438 x 266[6U]
Battery pack : 580 x 438 x
133[3U] x 2 pcs
UPS: 668 x 438 x 266[6U]
Battery pack : 580 x 438 x
133[3U] x 2 pcs
Net Weight (kgs)
UPS：42
Battery pack：63
UPS：45
Battery pack：63 x 2 pcs
UPS：45
Battery pack：63 x 2 pcs
Long-run
Model
Dimension, D X W X H
mm
668 x 438 x 266
668 x 438 x 266
668 x 438 x 266
Net Weight (kgs)
42
45
45
ENVIRONMENT
Operation Temperature
0 ~ 40°C (the battery life will down when > 25°C)
Operation Humidity
<95 % and non-condensing
Operation Altitude*
<1000m
Acoustic Noise Level
Less than 60dB @
1 Meter
Less than 65dB @ 1 Meter
MANAGEMENT
Smart RS-232 or USB
Supports Windows® 2000/2003/XP/Vista/2008, Windows® 7/8, Linux, Unix, and MAC
Optional SNMP
Power management from SNMP manager and web browser
*If the UPS is installed or used in a place where the altitude is above than 1000m, the output power must be derated one percent per 100m.
**Product specifications are subject to change without further notice.