Fujitsu MB95200H Series User manual

FUJITSU MICROELECTRONICS
SUPPORT SYSTEM
MCU-UM-500002-E-11
F²MC-8FX FAMILY
8-BIT MICROCONTROLLER
MB95200H/210H SERIES
STARTER KIT MB2146-410-01-E
SETUP GUIDE

Starter Kit MB2146-410-01-E Setup Guide V1.1
PREFACE
i
PREFACE
Thank you for purchasing the F2MC*
1
-8FX Family Starter Kit: MB2146-410-
01-E*
2
.
This product is a starter kit for F2MC-8FX MB95200H/210H series, which
comes with MB2146-08-E (F2MC-8FX Family BGM Adapter)*
3
, MB2146-
410-E (F2MC-8FX Family Evaluation Board)*
4
, and F2MC-8L/8FX Family
SOFTUNE Professional Pack Evaluation Version*
5
.
This manual explains how to use the Starter Kit. Be sure to read this manual
before using the product.
For mass production/evaluation MCUs for this product, consult with sales
representatives or support representatives.
*1: F2MC is the abbreviation of FUJITSU Flexible Microcontroller.
*2: Referred below as the “Starter Kit”.
*3: Referred below as the “BGMA”.
*4: Referred below as the “EV-Board”.
*5: Referred below as the “SOFTUNE”.
■Handling and use
Handling and use of this product and notes regarding its safe use are
described in the manuals for products bundled with the Starter Kit.
Follow the instructions in the manuals to use this product.
Keep this manual at hand so that you can refer to it anytime during use of
this product.
■Notice on this document
All information included in this document is current as of the date it is issued.
Such information is subject to change without any prior notice.
Please confirm the latest relevant information with the sales representatives.

Starter Kit MB2146-410-01-E Setup Guide V1.1
PREFACE
ii
■Caution of the products described in this document
The following precautions apply to the product described in this manual.
Indicates a potentially hazardous situation which, if not avoided appropriately,
could result in death or serious injury and/or a fault in the user’s system.
Electric shock,
Damage
Before performing any operation described in this manual, turn off all the power
supplies to the system. Performing such an operation with the power on ma
y
cause an electric shock or device fault.
Electric shock,
Damage
Once the product has been turned on, do not touch any metal part of it. Doing so
may cause an electric shock or device fault.
Indicates the presence of a hazard that may cause a minor or moderate injury,
damages to this product or devices connected to it, or may cause to loose software
resources and other properties such as data, if the device is not used
appropriately.
Cuts, Damage
Before moving the product, be sure to turn off all the
power supplies and unplug
the
cables. Watch your step when carrying the product. Do not use the product in
an
unstable location such as a place exposed to strong vibration or a sloping
surface. Doing so may cause the product to fall, resulting in an injury or fault.
Cuts
The product contains sharp edges that are left unavoidably exposed, such as
jumper
plugs. Handle the product with due care not to get injured with such
pointed parts.
Damage
Do not place anything on the product or expose the product to p
hysical shocks.
Do
not carry the product after the power has been turned on. Doing so may cause
a malfunction due to overloading or shock.
Damage
Since the product contains many electronic components, keep it away from direct
sunlight, high temperature, and high humidity to prevent condensation. Do not use
or store the product where it is exposed to much dust or a strong magnetic or
electric
field for an extended period of time. Inappropriate operating or storage
environments may cause a fault.
Damage
Use the product within the ranges given in the specifications.
Operation over the specified ranges may cause a fault.
Damage
To prevent electrostatic breakdown, do not let your finger or other object come
into contact with the metal parts of any of the conne
ctors. Before handling the
product, touch a metal object (such as a door knob) to discharge and any static
electricity from your body.
Damage
Before turning the power on, in particular, be sure to finish making all the required
connections. Furthermore, b
e sure to configure and use the product by following
the instructions given in this document. Using the product incorrectly or
inappropriately may cause a fault.
Damage
Always turn the power off before connecting or disconnecting any cables from the
produ
ct. When unplugging a cable, unplug the cable by holding the connector part
without pulling on the cable itself. Pulling the cable itself or bending it may expose
or disconnect the cable core, resulting in a fault.
Damage
Because the structure of the MCU
socket does not allow an evaluation MCU to be
mounted in the incorrect orientation, be very careful of the orientation of the
evaluation MCU when mounting it. Inserting the evaluation MCU in the wrong
orientation may damage the MCU, causing the MCU to become faulty.
Damage
Because the product has no casing, it is recommended that it be stored in the
original
packaging. Transporting the product may cause a damage or fault.
Therefore, keep the packaging materials and use them in case of for the re-
shipment of the product.
WARNING
CAUTION

Starter Kit MB2146-410-01-E Setup Guide V1.1
PREFACE
iii
© 2008 FUJITSU MICROELECTRONICS LIMITED
The contents of this document are subject to change without notice.
Customers are advised to consult with sales representatives before ordering.
The information, such as descriptions of function and application circuit examples, in this document are
presented solely for the purpose of reference to show examples of operations and uses of FUJITSU
MICROELECTRONICS semiconductor device; FUJITSU MICROELECTRONICS does not warrant proper
operation of the device with respect to use based on such information. When you develop equipment
incorporating the device based on such information, you must assume any responsibility arising out of
such use of the information. FUJITSU MICROELECTRONICS assumes no liability for any damages
whatsoever arising out of the use of the information.
Any information in this document, including descriptions of function and schematic diagrams, shall not be
construed as license of the use or exercise of any intellectual property right, such as patent right or
copyright, or any other right of FUJITSU MICROELECTRONICS or any third party or does FUJITSU
MICROELECTRONICS warrant non-infringement of any third-party's intellectual property right or other
right by using such information. FUJITSU MICROELECTRONICS assumes no liability for any
infringement of the intellectual property rights or other rights of third parties which would result from the
use of information contained herein.
The products described in this document are designed, developed and manufactured as contemplated for
general use, including without limitation, ordinary industrial use, general office use, personal use, and
household use, but are not designed, developed and manufactured as contemplated (1) for use
accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious
effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss
(i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport
control, medical life support system, missile launch control in weapon system), or (2) for use requiring
extremely high reliability (i.e., submersible repeater and artificial satellite). Please note that FUJITSU
MICROELECTRONICS will not be liable against you and/or any third party for any claims or damages
arising in connection with above-mentioned uses of the products.
Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage
or loss from such failures by incorporating safety design measures into your facility and equipment such
as redundancy, fire protection, and prevention of over-current levels and other abnormal operating
conditions.
Exportation/release of any products described in this document may require necessary procedures in
accordance with the regulations of the Foreign Exchange and Foreign Trade Control Law of Japan and/or
US export control laws.
The company names and brand names herein are the trademarks or registered trademarks of their
respective owners.

Starter Kit MB2146-410-01-E Setup Guide V1.1
Contents
iv
Contents
PREFACE ................................................................................................................... i
■ Handling and use.......................................................................................................... i
■ Notice on this document................................................................................................ i
■ Caution of the products described in this document ......................................................ii
Contents................................................................................................................... iv
1 PRODUCT OVERVIEW ................................................................................................. 1
1.1 Objective and Deliverable........................................................................................ 1
1.2 System Block .......................................................................................................... 1
1.3 Handling Precautions .............................................................................................. 1
1.4 Feature.................................................................................................................... 2
1.5 Hardware Setup ...................................................................................................... 2
2 BGMA MANUAL............................................................................................................ 3
2.1 BGMA Overview...................................................................................................... 3
2.2 Function List............................................................................................................ 3
2.3 IDC10 Interface Description .................................................................................... 4
2.4 BGMA USB Configuration ....................................................................................... 4
2.5 LED Description ...................................................................................................... 7
3 EV-BOARD MANUAL.................................................................................................... 8
3.1 EV-board Overview ................................................................................................. 8
3.2 Function List............................................................................................................ 9
3.3 EV-board Schematic ............................................................................................. 10
3.4 HW Module Description and Jumper settings ........................................................ 11
3.4.1 Power Module.......................................................................................... 11
3.4.2 BGMA Interface ....................................................................................... 12
3.4.3 Clock Settings.......................................................................................... 12
3.4.4 Buzzer Module......................................................................................... 12
3.4.5 A/D Module.............................................................................................. 13
3.4.6 LED Module............................................................................................. 13
3.4.7 Key Module.............................................................................................. 14
3.4.8 Lin-UART Module .................................................................................... 14
4 SAMPLE CODE MANUAL........................................................................................... 15
4.1 Topic List............................................................................................................... 15
4.2 Project Structure.................................................................................................... 17
4.3 Source Code File Description................................................................................ 18
4.3.1 Header Files ............................................................................................ 18

Starter Kit MB2146-410-01-E Setup Guide V1.1
Contents
v
4.3.2 Startup.asm File....................................................................................... 19
4.3.3 Vectors.c File........................................................................................... 19
4.3.4 Main.c File ............................................................................................... 20
5 DEVELOPMENT PLATFORM QUICK START ............................................................ 21
5.1 Tools Setup Sequence .......................................................................................... 21
5.2 Open Project and Start Debug............................................................................... 21
5.3 Operation Precautions........................................................................................... 21

Starter Kit MB2146-410-01-E Setup Guide V1.1
Chapter 1 Product Overview
MCU-UM-500002-E-11 – Page 1
1 Product Overview
This product is a set of Starter Kit (MB2146-410-01-E) of MB95200H/210H series. It is
composed of a BGMA (MB2146-08-E) and an EV-board (MB2146-410-E). Combining the
SOFTUNE Workbench on PC, the Starter kit enables the quick start of development before
the user system is ready.
1.1 Objective and Deliverable
The Starter kit (MB2146-410-01-E) provides users a complete development platform. Before
start using the Starter Kit, make sure that the following devices are placed in the package:
BGMA (MB2146-08-E) 1PCS;
EV-board (MB2146-410-E) 1PCS;
USB cable 1PCS
CD-ROM (SOFTUNE, user manuals, sample code) 1PCS
Hardcopy (China RoHS report, quick start guide) 1PCS
AA battery 4PCS
1.2 System Block
To setup a debugging system, connect a PC, a BGMA and an EV-board together as shown
below:
Figure 1.2-1 System Block
1.3 Handling Precautions
The Starter Kit can be used in connection with its bundled products. To ensure correct use of
this product in a proper environment, observe the following guideline:
Follow the instructions described in each manual for the bundled product to use this
product.
BGMA
USB
Target Board
Host PC
SOFTUNE
IDE
Sample code
Easy design and study
MB95200H/210H MCU
with BGMA and SOFTUNE
MB95200H/210H
MCU

Starter Kit MB2146-410-01-E Setup Guide V1.1
Chapter 1 Product Overview
MCU-UM-500002-E-11 – Page 2
1.4 Feature
The F2MC-8FX starter kit is the best for a performance and functional evaluation, and a
check of operation before including F2MC-8FX in a user's system.
Below, the feature of the BGM debugger for F2MC-8FX is shown.
Microcomputer operation voltage It corresponds to +2.7V to +5.5V.
(The maximum and minimum of microcomputer operation voltage and frequency of
operation differs with each MCU. refer to the documents (a data sheet, hardware
manual, etc.) of each device relation for the operation voltage and frequency of MCU of
operation.)
Compact development environment, a light and small BGM Adapter.
Since a monitor program is performed in exclusive memory space, it does not consume
user memory space.
Continuation execution, step execution and break correspondence.
It connects with a host computer by the USB interface.
1.5 Hardware Setup
In the hardware setup procedure, you configure and connect the hardware products. This
chapter includes the configuring and connecting procedure for each product in order. Check
the contents and complete the hardware setup.
Configuration of each product
- Configuring EV-Board
Connection of each product
- Connecting BGMA and EV-board
- Connecting EV-Board power supply

Starter Kit MB2146-410-01-E Setup Guide V1.1
Chapter 2 BGMA Manual
MCU-UM-500002-E-11 – Page 3
2 BGMA Manual
This chapter gives introduction how to setup BGMA.
2.1 BGMA Overview
Below is the close look of the BGMA. The Part Number of the MB95200H/210H BGMA is
MB2146-08-E. It provides a debug platform for the MB95200H/210H MCU in a small size
(128mmX55mmX29mm).
Figure 2.1-1 BGMA overview
2.2 Function List
ID Function description Remarks
1 Support 8FX-MB95200H/210H Series
MCU
MCU MAX machine clock: 16.25 MHz
MCU power voltage: 2.4 V ~ 5.5 V
2 Break pointer 256 software breakpoints
3 USB interface to PC/SOFTUNE Compatible to USB protocol version 1.1
4 1-Line UART interface to
the
MB95200H/210H MCU The Baud rate is 62,500 bps
5 Support the
MCU flash programming
for engineering development
Provide high voltage for flash operation.
The program and read speed is about 800 B/S.

Starter Kit MB2146-410-01-E Setup Guide V1.1
Chapter 2 BGMA Manual
MCU-UM-500002-E-11 – Page 4
2.3 IDC10 Interface Description
Pin Number Pin Name Description
1 UVCC Target MCU Vcc
2 GND Target MCU Vss
3 RSTIN Target MCU reset input
4 RSTOUT Target MCU reset output
5 RSV Reserved
6 RSV Reserved
7 RSV Reserved
8 DBG Target MCU debug pin
9 RSV Reserved
10 RSV Reserved
2.4 BGMA USB Configuration
The BGMA is provided with a USB cable. Connect the BGMA to a PC with a USB cable. If
the connection is right, the following window will pop up. Follow the instructions displayed,
and then click “Next”,
Figure 2.4-1 Install BGMA in Windows (1)

Starter Kit MB2146-410-01-E Setup Guide V1.1
Chapter 2 BGMA Manual
MCU-UM-500002-E-11 – Page 5
Select “Install from a list or specific location (Advanced)”, then click “Next”,
Figure 2.4-2 Install BGMA in Windows (2)
Select “…\Drivers” from the folder where SOFTUNE is installed, click “Next”,
Figure 2.4-3 Install BGMA in Windows (3)

Starter Kit MB2146-410-01-E Setup Guide V1.1
Chapter 2 BGMA Manual
MCU-UM-500002-E-11 – Page 6
Select BGMA (MB2146-08) as displayed below, and then click “Next”,
Figure 2.4-4 Install BGMA in Windows (4)
Windows will install the driver automatically. Click “Finish” after the driver has completed the
installation normally. Then users can find the BGMA is recognized as MB2146-08 in
Windows system.
Figure 2.4-5 BGMA is installed in Windows

Starter Kit MB2146-410-01-E Setup Guide V1.1
Chapter 2 BGMA Manual
MCU-UM-500002-E-11 – Page 7
2.5 LED Description
First, only plug USB cable to PC, check the Power LED on BGMA turns Green. Refer to
Figure 2.5-1.
Figure 2.5-1 BGMA Power LED (1)
Second, plug IDC10 cable to the EV-board (target MCU board), then turn on EV-board. After
that check Power LED on the BGMA turns Orange. Refer to Figure 2.5-2.
Figure 2.5-2 BGMA Power LED (2)
Green
USB Plug
ged to
PC
Orange
5V Power
through
IDC
Cable

Starter Kit MB2146-410-01-E Setup Guide V1.1
Chapter 3 EV-board Manual
MCU-UM-500002-E-11 – Page 8
3 EV-board Manual
This chapter gives introduction how to setup EV-board.
3.1 EV-board Overview
MB95200H/210H MCU EV-board is provided as a user-friendly introductory and evaluation
platform for the MB95200H/210H MCU Family microcontroller. Figure 3.1-1 below is a close
look of EV-board.
Figure 3.1-1 EV-board Overview
MB95200H/210H
MCU
Debug Interface
to BGMA
Power supply either from
batteries (below the PCB) or
from 2-pin header
Circuit for
LIN-UART
peripheral
communication
Switch circuit to MCU
External Interrupt pins
Buzzer circuit
Potentiometer to
MCU AD pin
LEDs to MCU
I/O port pins
Jumpers to set MCU
pins connected to
external circuits or not
Jumpers left open
when debug

Starter Kit MB2146-410-01-E Setup Guide V1.1
Chapter 3 EV-board Manual
MCU-UM-500002-E-11 – Page 9
3.2 Function List
The EV-board consists of a board and a sample firmware. The board provides a useful
platform for using the MCU and its peripherals. It is a useful development platform together
with a BGMA (PN: MB2146-08-E) and a SOFTUNE. It features the following functions,
Clock and sub-clock
USB 5V power IF, external 5V power IF and the battery
Reset circuit and reset key
Provide IDC10 debug interface
LEDs for general use, LED1 indicates DBG pin work status
Provide one buzzer to demonstrate timer output
2 keys for general use
Potentiometer and temperature sensor
RS-232 level converter and DB9 interface (MAX232)
LIN circuit reserved
SIO 4 pins reserved
All MCU ports are easy accessible through test pins
Optional Starter kit to support each available MCU packages

Starter Kit MB2146-410-01-E Setup Guide V1.1
Chapter 3 EV-board Manual
MCU-UM-500002-E-11 – Page 10
3.3 EV-board Schematic
Figure 3.3-1 EV-board Schematic

Starter Kit MB2146-410-01-E Setup Guide V1.1
Chapter 3 EV-board Manual
MCU-UM-500002-E-11 – Page 11
3.4 HW Module Description and Jumper settings
3.4.1 Power Module
Users can select two types of DC power supply to the EV-board. If any of the power supplies
is connected to the EV-board correctly, power LED (LED5) on the EV-board will be on. Refer
to Figure 3.4.1-1.
Figure 3.4.1-1 Power Module
To select different power supplies, follow the table below,
Power supply Header name Settings
4 AA batteries from
BT1 on the back of
the EV-board.
J1: BAT.
9V DC from CN6 J1: 9V.
Table 3.4.1-1 Power Supply Selection

Starter Kit MB2146-410-01-E Setup Guide V1.1
Chapter 3 EV-board Manual
MCU-UM-500002-E-11 – Page 12
3.4.2 BGMA Interface
To start the debug using a BGMA, users shall connect IDC10 socket from the BGMA to CN1
on an EV-board, and J2 shall be open in a debug mode. In a normal (free-run) mode, J2
shall be closed to enable reset key S3. Refer to Figure 3.4.2-1.
Figure 3.4.2-1 Debug Interface
MCU Mode Header name Settings
Debug mode J2
User mode J2
3.4.3 Clock Settings
The MB95200H/210H series MCU uses an internal main RC as a clock source by default.
Users can select on-board crystal as a main clock and a sub-clock. Follow the settings below:
Clock Header name Settings
Main clock SW3: X1, X0
Sub-clock SW3: X1A, X0A
Table 3.4.3-1
3.4.4 Buzzer Module
A buzzer module is provided to demonstrate an 8/16 composite timer output (a continuous
mode). To enable buzzer module, follow the table below:
Modules Header name Settings
Buzzer:
BUZ1 SW1: BUZ.
Table 3.4.4-1