Fujitsu MB86R11 User manual

MB86R11 Evaluation Board
MB86R11EVB
Hardware Manual
January, 2011
The 1.1 edition
FUJITSU SEMICONDUCTOR LIMITED

ii
MB86R11 Evaluation Board
MB86R11EVB Hardware Manual
Preface
Objectives and Intended Reader
MB86R11EVB is an evaluation board of LSI MB86R11 for graphics applications.
This manual describes hardware specifications of MB86R11EVB for engineers who evaluate MB86R11
basic function.
Trademarks
ARM is a registered trademark of ARM Limited in the EU and other countries.
Cortex is a trademark of ARM Limited in the EU and other countries.
The company names and brand names herein are the trademarks or registered trademarks of their
respective owners.
Notation
Term Description
MB86R11EVB Generic term of MB86R11 evaluation board which is a set of MB86R11EVB-CPU01 (CPU
board), MB86R11EVB-BASE01 (Base board), and MB86R11EVB-OPT01 (Option board).

iii
MB86R11 Evaluation Board
MB86R11EVB Hardware Manual
• The contents of this document are subject to change without notice.
Customers are advised to consult with sales representatives before ordering.
• The information, such as descriptions of function and application circuit examples, in this document are
presented solely for the purpose of reference to show examples of operations and uses of FUJITSU
SEMICONDUCTOR device; FUJITSU SEMICONDUCTOR does not warrant proper operation of the device
with respect to use based on such information. When you develop equipment incorporating the device based
on such information, you must assume any responsibility arising out of such use of the information. FUJITSU
SEMICONDUCTOR assumes no liability for any damages whatsoever arising out of the use of the
information.
• Any information in this document, including descriptions of function and schematic diagrams, shall not be
construed as license of the use or exercise of any intellectual property right, such as patent right or copyright,
or any other right of FUJITSU SEMICONDUCTOR or any third party or does FUJITSU
SEMICONDUCTOR warrant non-infringement of any third-party's intellectual property right or other right
by using such information. FUJITSU SEMICONDUCTOR assumes no liability for any infringement of the
intellectual property rights or other rights of third parties which would result from the use of information
contained herein.
• The products described in this document are designed, developed and manufactured as contemplated for
general use, including without limitation, ordinary industrial use, general office use, personal use, and
household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying
fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public,
and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction
control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life
support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability
(i.e., submersible repeater and artificial satellite).
Please note that FUJITSU SEMICONDUCTOR will not be liable against you and/or any third party for any
claims or damages arising in connection with above-mentioned uses of the products.
• Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or
loss from such failures by incorporating safety design measures into your facility and equipment such as
redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions.
• Exportation/release of any products described in this document may require necessary procedures in
accordance with the regulations of the Foreign Exchange and Foreign Trade Control Law of Japan and/or US
export control laws.
• The company names and brand names herein are the trademarks or registered trademarks of their respective
owners.
All rights reserved, Copyright FUJITSU SEMICONDUCTOR LIMITED 2011

iv
MB86R11 Evaluation Board
MB86R11EVB Hardware Manual
Revision History
Date Ver. Contents
2011/1/13 1.0 Newly issued
2011/1/25 1.1
Table 9-1 Revised description
Added FPGA specifications

v
MB86R11 Evaluation Board
MB86R11EVB Hardware Manual
Contents
1. Outline of MB86R11EVB..................................................................................... 1
1.1. Composition ............................................................................................................................................ 1
1.2. General specifications ............................................................................................................................. 2
1.3. External view .......................................................................................................................................... 3
1.4. Connection configuration........................................................................................................................ 5
2. Outline of Hardware............................................................................................ 6
2.1. Hardware specifications of CPU board................................................................................................... 6
2.2. Hardware specifications of Base board ................................................................................................... 7
2.3. Hardware specifications of Option board................................................................................................ 9
2.4. Block diagram ....................................................................................................................................... 10
3. Details of hardware............................................................................................11
3.1. CPU board..............................................................................................................................................11
3.1.1. External Bus...................................................................................................................................11
3.1.2. DDR2 .............................................................................................................................................11
3.1.3. USB-Host .......................................................................................................................................11
3.1.4. USB-Function ............................................................................................................................... 12
3.1.5. ARM JTAG/ETM.......................................................................................................................... 12
3.1.6. Selection of boot flash memory..................................................................................................... 13
3.1.7. Pin Multiplex Switch..................................................................................................................... 14
3.1.8. Jumper setting ............................................................................................................................... 16
3.2. Base board............................................................................................................................................. 17
3.2.1. FPGA ............................................................................................................................................ 17
3.2.2. External Bus.................................................................................................................................. 17
3.2.3. Display .......................................................................................................................................... 18
3.2.4. Capture.......................................................................................................................................... 24
3.2.5. Ethernet ......................................................................................................................................... 26
3.2.6. EEPROM ...................................................................................................................................... 26
3.2.7. I2S (AUDIO)................................................................................................................................. 26
3.2.8. CAN .............................................................................................................................................. 27
3.2.9. USART (UART)............................................................................................................................ 28
3.2.10. GPIO ............................................................................................................................................. 29
3.2.11. SDIO ............................................................................................................................................. 30
3.2.12. TS.................................................................................................................................................. 31
3.2.13. MediaLB ....................................................................................................................................... 32
3.2.14. Pin Multiplex Switch..................................................................................................................... 33
3.3. Option board ......................................................................................................................................... 37
3.3.1. Display .......................................................................................................................................... 37
3.3.2. I2S (AUDIO)................................................................................................................................. 43
3.3.3. CAN .............................................................................................................................................. 44
3.3.4. USART (UART)............................................................................................................................ 44
3.3.5. LIN................................................................................................................................................ 45

vi
MB86R11 Evaluation Board
MB86R11EVB Hardware Manual
3.3.6. SDIO ............................................................................................................................................. 46
3.3.7. PWM ............................................................................................................................................. 47
3.3.8. IrDA .............................................................................................................................................. 48
3.3.9. IDE................................................................................................................................................ 49
3.3.10. SPI-FLASH (Quad)....................................................................................................................... 50
3.3.11. SPI-FLASH (Single) ..................................................................................................................... 50
3.3.12. I2C................................................................................................................................................. 50
3.3.13. General-purpose ADC................................................................................................................... 51
3.3.14. TCON............................................................................................................................................ 52
3.3.15. External INT.................................................................................................................................. 52
4. Board interface ................................................................................................. 53
4.1. CPU – Base board I/F ........................................................................................................................... 53
4.2. Base – Option board I/F ........................................................................................................................ 58
4.3. Customer I/F ......................................................................................................................................... 63
5. Memory map ..................................................................................................... 66
5.1. MB86R11EVB memory map................................................................................................................ 66
5.2. FPGA register........................................................................................................................................ 66
5.2.1. VERSION register ........................................................................................................................ 67
5.2.2. PINMUX register .......................................................................................................................... 68
5.2.3. DEVICE_SEL register .................................................................................................................. 70
5.2.4. ACC_TEST register ...................................................................................................................... 71
5.2.5. FPGA signal timing....................................................................................................................... 72
6. Allocation of peripheral resource and I2C port.............................................. 73
7. Power system diagram..................................................................................... 74
8. Clock system diagram...................................................................................... 77

1 1. Outline of MB86R11EVB
MB86R11 Evaluation Board
MB86R11EVB Hardware Manual
1. Outline of MB86R11EVB
This chapter describes the outline of MB86R11EVB.
1.1. Composition
MB86R11EVB consists of following 3 evaluation boards:
MB86R11EVB-CPU01 (CPU board)
This board mounts MB86R11.
MB86R11EVB-BASE01 (Base board)
This board has external I/F and the power supply input part.
MB86R11EVB-OPT01 (Option board)
This board mounts only the external peripheral functions.
The pin of MB86R11 is multifunctional, and is switched by the external pin setting or the register setting.
In MB86R11EVB, to realize the switching of each resource according to the setting mode by an enable
control, the buffer is inserted between MB86R11 and each resource.
This board executes an enable control with FPGA, and has the selector function of Display and Capture.

2 1. Outline of MB86R11EVB
MB86R11 Evaluation Board
MB86R11EVB Hardware Manual
1.2. General specifications
The table below shows the general specifications.
Table 1-1 General specifications
No. Item Contents Remarks
1 Board name
CPU board
Base board
Option board
2 Function
DDR2
Flash ROM
Display I/F
Capture I/F
Ethernet I/F
I2S I/F
MLB I/F
CAN I/F
LIN (USART) / UART I/F
SD I/F
USB I/F
PWM I/F
GPIO I/F
IrDA I/F
IDE I/F
TS I/F
JTAG I/F
TRACE I/F
I2C I/F
A/D I/F
TCON
Quad-SPI
SFI
External Bus
DMA REQ
External INT
SW
LED
3 Operating ambient
temperature Normal temperature
4 Storage temperature 0 to 70°C
5 Humidity Normal humidity No condensation
6 Environment friendly Conforming product
7 Power supply AC adaptor input +12V 5A or less
8 Board dimensions
CPU board
W H = 127mm 117.5mm
Base board
W H = 330mm 222.5mm
Option board
W H = 222.5mm 105mm

3 1. Outline of MB86R11EVB
MB86R11 Evaluation Board
MB86R11EVB Hardware Manual
1.3. External view
The external view of MB86R11EVB is shown as follows.
Figure 1-1 External view of MB86R11EVB
External view of CPU board
Figure 1-2 External view of CPU board

4 1. Outline of MB86R11EVB
MB86R11 Evaluation Board
MB86R11EVB Hardware Manual
External view of Base board
Figure 1-3 External view of Base board
External view of Option board
Figure 1-4 External view of Option board

5 1. Outline of MB86R11EVB
MB86R11 Evaluation Board
MB86R11EVB Hardware Manual
1.4. Connection configuration
The connection configuration is shown as follows.
Base Board
CPU Board Option Board
Base Board
CPU Board
Option Board
MB86R1
1
AB
AB
CPUboard side connector CN8
Base board side connector
CN31
CPU board side connector CN9
Base board side connector
CN32
Option board side connector
CN7
Base board side connector
CN33
Option board side connector
CN8
Base board side connector
CN34
Figure 1-5 Connection configuration of MB86R11EVB

6 2. Outline of Hardware
MB86R11 Evaluation Board
MB86R11EVB Hardware Manual
2. Outline of Hardware
This chapter describes the outline of hardware of MB86R11EVB.
2.1. Hardware specifications of CPU board
Table 2-1 shows the hardware specifications of CPU board.
Table 2-1 Hardware specifications of CPU board
Used CPU
1 MB86R11 PBGA-544pin
Installed function
No. Item Contents Remarks
1 DDR2 MT47H64M16HR-25E_IT (Micron) 2
1Gbit (64M×16bit) 2
2 NOR-FLASH JS28F512M29EWL (Numonyx) 2
512Mbit (32Mword 16bit) 2
This is a composition when 32bit bus is
connected.
When boot from NOR-FLASH is used, it
becomes a composition of 512Mbit 1 because
the bus is fixed to 16bit.
3 USB-Host 292303-1 (Tyco) USB-A connector
USB-Host 292303-1 (Tyco) USB-A connector
(Exclusive use with USB-Function)
4
USB-Function UX60SC-MB-5ST (HRS) Mini-B connector
(Exclusive use with USB-Host)
5 ICE PS-20PE-D4T1-B1 (JAE) JTAG connector
6 TRACE 2-5767004-2 (Tyco) ETM connector
7 Base board connection 53647-1674 (Molex) 2 160pin stack

7 2. Outline of Hardware
MB86R11 Evaluation Board
MB86R11EVB Hardware Manual
2.2. Hardware specifications of Base board
Table 2-2 shows the hardware specifications of Base board.
Table 2-2 Hardware specifications of Base board (1/2)
Used FPGA
1 Spartan6 XC6SLX100-2FGG676C (Xilinx) FBGA-676pin
No. Item Contents Remarks
DVI-D The connector is DVI-I.
SiI164BCT64 (Silicon Image)
CVBS ADV7343BSTZ (Analog devices)
Analog RGB ADV7343BSTZ (Analog devices)
RSDS (Header pin)
OQW-11-4.2-20PW (Mac8) 1.27mm pitch
Diplay0
External output (Header pin)
OQW-11-4.2-20PW (Mac8) 1.27mm pitch
DVI-D The connector is DVI-I.
SiI164BCT64 (Silicon Image)
1 Display (2ch)
Display1 External output (Header pin)
OQW-11-4.2-20PW (Mac8) 1.27mm pitch
DVI-D SiI1161CT (Silicon Image)
The connector is DVI-I.
CVBS (YUV) ADV7403KSTZ (Analog devices)
Capture0
External input (Header pin)
OQW-11-4.2-20PW (Mac8) 1.27mm pitch
CVBS (YUV) ADV7403KSTZ (Analog devices)
Video Component (720P) ADV7403KSTZ (Analog devices)
External input (Header pin)
OQW-11-4.2-10PW (Mac8) 1.27mm pitch
CVBS (YUV) ADV7403KSTZ (Analog devices)
External input (Header pin)
OQW-11-4.2-10PW (Mac8) 1.27mm pitch
CVBS (YUV) ADV7403KSTZ (Analog devices)
2 Capture (4ch)
Capture1
External input (Header pin)
OQW-11-4.2-10PW (Mac8) 1.27mm pitch
3 Ethernet RJ45 connector
TM21R-5C-88 (HRS)
GbE-PHY
88E1111-B2-BAB-C000 (Marvell)
Stereo mini Jack 1
STX-3500-4N (Kycon) OUTPUT
4 I2S (CH0: AUDIO)
Stereo mini Jack 1
STX-3500-4N (Kycon) INPUT
5 MediaLB Connector for evaluation (Header pin)
A3A-10PA-2SV (71) (Hirose) 2.0mm pitch
6 CAN (CH0)
D-sub9
RDED-9P-LNA (4-40) (55)
(HONDA TSUSHIN)
D-sub9
RDED-9P-LNA (4-40) (55)
(HONDA TSUSHIN)
7 USART/UART (CH0, CH1)
External input/output (Header pin)
OQW-11-4.2-03PW (Mac8) 1.27mm pitch
8 SD (CH0) SD card slot
DM1AA-SF-PEJ(HRS)

8 2. Outline of Hardware
MB86R11 Evaluation Board
MB86R11EVB Hardware Manual
Table 2-2 Hardware specifications of Base board (2/2)
No. Item Contents Remarks
LED for power supply (Green)
LED 1 SML-310MT (ROHM)
It lights when SW17 is turned on when
the power is supplied to the Base board.
LED for FPGA reset (Green)
LED 1 SML-310MT (ROHM) It lights when FPGA is reset.
9 LED
LED for configuration (Green)
LED 1 SML-310MT (ROHM)
It lights when the FPGA configuration is
completed.
LED 4
SML-310MT (ROHM) Green LED
CH11-14 External input/output (Header pin)
OQW-11-4.2-03PW (Mac8)
10 GPIO 10
CH5-10 SW 6
SKRPABE010 (ALPS ELECTRIC) Tact switch
11 TS External pin (Header pin)
OQW-11-4.2-07PW (Mac8) 1.27mm pitch
12 I2C (CH0, CH1) For setting of IC
13 EEPROM BR25S256F (ROHM)
256Kbit
SW 1
SKRPABE010 (ALPS ELECTRI) Tact switch
INT_A0 External input (Header pin)
FFC-03ASM1 (HONDA TSUSHI) 2.54mm pitch
14 External INT
INT_A1 External input (Header pin)
FFC-03ASM1 (HONDA TSUSHI) 2.54mm pitch
15 NAND FLASH MT29F2G08ABAEAWP (Micron)
2Gbit (8bit Bus)
JTAG 98424-G52-14ALF (FCI) For FPGA writing
16 FPGA
configuration Config-ROM S25FL032P0XMFI011 (SPANSION) Quad SPI
17 CPU board connection 52837-1679 (Molex) 2 160pin stack
18 Option board connection 52837-1679 (Molex) 2 160pin stack
19 Customer board connection
connector 87BFN100R-3F (KEL) 100pin right angle
20 MB86R11 mode selection switch
8bit slide switch 4
CHS-08B (NIDEC COPAL
ELECTRONICS)
21 Capture input selection switch
8bit slide switch
CHS-08B (NIDEC COPAL
ELECTRONICS)

9 2. Outline of Hardware
MB86R11 Evaluation Board
MB86R11EVB Hardware Manual
2.3. Hardware specifications of Option board
Table 2-3 shows the hardware specifications of Option board.
Table 2-3 Hardware specifications of Option board
No. Item Contents Remarks
Diplay0 DVI-D The connector is DVI-I.
SiI164BCT64(Silicon Image)
Diplay1 DVI-D The connector is DVI-I.
SiI164BCT64(Silicon Image)
DVI-D The connector is DVI-I.
SiI164BCT64(Silicon Image)
1 Display (3ch)
Diplay2 External output (Header pin)
OQW-11-4.2-20PW (Mac8) 1.27mm pitch
OUT: Stereo mini Jack 1
STX-3500-4N (Kycon)
2 I2S (CH1)
IN: Stereo mini Jack 1
STX-3500-4N (Kycon)
3 I2S (CH2, CH3) External input/output (Header pin)
OQW-11-4.2-04PW (Mac8) 1.27mm pitch
4 CAN (CH1)
D-sub9
RDED-9P-LNA (4-40) (55)
(HONDA TSUSHIN)
5 LIN (USART)/UART (CH5) B2B-PH-SM4-TB (JST)
6 SD 2 (CH1, CH2) SD card slot
DM1AA-SF-PEJ (HRS)
7 PWM 12 External output (Header pin)
OQW-11-4.2-07PW (Mac8) 1.27mm pitch
8 IrDA External input/output (Header pin)
OQW-11-4.2-06PW (Mac8) 1.27mm pitch
9 I2C (CH2～4) External input/output (Header pin)
FFC-03ASM1 (HONDA TSUSHIN) 2.54mm pitch
10 General-purpose ADC External input/output (Header pin)
OQW-11-4.2-05PW (Mac8) 1.27mm pitch
11 TCON External output (Header pin)
OQW-11-4.2-07PW (Mac8) 1.27mm pitch
12 SPI-FLASH (Quad) S25FL064P0XMFI001 (Spansion)
64Mbit
13 SPI-FLASH (Single) W25Q32BVSSIG (Winbond)
32Mbit
14 External INT (CH2) External input (Header pin)
OQW-11-4.2-04PW (Mac8) 1.27mm pitch
15 DMA REQ External input/output (Header pin)
FFC-03ASM1 (HONDA TSUSHIN) 2.54mm pitch
16 IDE External input/output (Header pin)
WCAW-20-2-22PW (Mac8)

10 2. Outline of Hardware
MB86R11 Evaluation Board
MB86R11EVB Hardware Manual
2.4. Block diagram
Figure 2-1 shows the block diagram of MB86R11EVB.
MB86R11 FPGA DISP0
DISP1
DISP2
DDR2
Nor Flash
ICE
TRACE
USB-
Host
USB-
Host
USB-
Function
CAP0
PINPIN
PIN
DISP0
DISP1
PIN
CAP1
PIN
CAP2
PIN
CAP3
PIN
Ethernet
CAN
USART
SD Card
TS
NAND
Flash
AUDIO
GPIO
AUDIO
USART
SD Card
PWM
IrDA
DMA REQ
Quad SPI
SPI Flash
I2C
A/D
TCON
INT
Enable signal of
each buffer
MLB
PINPIN
I2C
EEPROM
INT
CAN
PIN
PIN
(RSDS)
IDE
LIN
Figure 2-1 Block diagram of MB86R11EVB

11 3. Details of hardware
MB86R11 Evaluation Board
MB86R11EVB Hardware Manual
3. Details of hardware
This chapter describes details of the hardware of MB86R11EVB.
3.1. CPU board
Single-chip system LSI MB86R11 with built-in CoreTex-A9 is used for CPU.
Table 3-1 CPU
No. Item Model number Manufacturer Quantity Remarks
1 CPU MB86R11 Fujitsu Semiconductor 1 PBGA544pin
3.1.1. External Bus
NOR-FLASH of 1Gbit (512Mbit) is connected to External Bus of CPU board.
Table 3-2 NOR-FLASH
No. Item Model number Manufacturer Quantity Remarks
1 NOR-FLASH JS28F512M29EWL Numonyx 2 128MB
(32Mword×16bit×2)
3.1.2. DDR2
The CPU board has 2Gbit (1Gbit 2) as DDR2 interface.
It is a composition in which 4Gbit (2Gbit 2) can be connected.
Table 3-3 DDR2
No. Item Model number Manufacturer Quantity Remarks
1 DDR2 MT47H64M16HR-25E_IT MICRON 2 256MB
(64Mb 16bit 2)
3.1.3. USB-Host
The CPU board has the USB2.0-Host by 2 ports (CN3 and CN5).
The CN3 is exclusively used with Function (CN4).
Table 3-4 USB-Host
No. Item Model number Manufacturer Quantity Remarks
1 USB connector 292303-1 Tyco 2 TypeA
2 High side switch TPS2061D TI 1 Power supply control
3 Crystal oscillator MXO3-7050 48MHz MITADENPA 1 48MHz/50ppm
All USB ports

12 3. Details of hardware
MB86R11 Evaluation Board
MB86R11EVB Hardware Manual
3.1.4. USB-Function
The CPU board has the USB2.0-Function by 1 port (CN4).
VBUS is connected to INT_A[1].
Table 3-5 USB-Function
No. Item Model number Manufacturer Quantity Remarks
1 USB connector UX60SC-MB-5ST HRS 1 miniB
2 Schmitt buffer SN74LVC1G17DCK TI 1 VBUS detection
3 Crystal oscillator MXO3-7050 48MHz MITADENPA 1 48MHz/50ppm
All USB ports
3.1.5. ARM JTAG/ETM
The CPU board has JTAG (CN1) and the ETM connector (CN2) for the ARM debugging.
Enable ETM probe (HLX600TP) and JTAG cable (HLX600JP) of YDC AdviceLUNA to be connected.
Table 3-6 ARM JTAG/ETM
No. Item Model number Manufacturer Quantity Remarks
1 JTAG PS-20PE-D4T-B1 JAE 1 2列20極
2 ETM 2-5767004-2 Tyco 1 2列38極

13 3. Details of hardware
MB86R11 Evaluation Board
MB86R11EVB Hardware Manual
3.1.6. Selection of boot flash memory
The CPU board has the switch that selects the boot memory. It can select either of NOR-FLASH or
NAND-FLASH of the external memory.
Table 3-7 Slide switch
No. Item Model number Manufacturer Quantity Remarks
1 Slide switch MAS-D20A1 Fujisoku 1
SW1 (Selection of boot memory type)
Table 3-8 SW1 setting
SW1 Boot memory type Remarks
MB86R11 side NAND-FLASH Cannot used
The other side NOR-FLASH (Default) Default
NOR-FLASH
NAND-FLASH
MB86R11

14 3. Details of hardware
MB86R11 Evaluation Board
MB86R11EVB Hardware Manual
3.1.7. Pin Multiplex Switch
The setting of each switch on CPU board is as follows.
Table 3-9 DIP SW
No. Item Model number Manufacturer Quantity Remarks
1 DIP SW CHS-08B NIDEC COPAL
ELECTRONICS
2
SW2 (PLLMODE)
Table 3-10 SW2 setting
SW2 Signal Description Default
4:1 CRIPM[3:0] ON=0, OFF=1
SW[4, 3, 2, 1]=[ON, ON, ON, ON]=0000
SW[4, 3, 2, 1]=[OFF, OFF, OFF, OFF]=1111
SW[4, 3, 2, 1]=
[OFF, ON, ON, ON]
5 PLLBYPASS OFF=PLL clock is not bypassed.
ON=PLL clock is bypassed.
OFF
6 PSMODE ON=PSMODE are reflected to the PLL clock frequency.
OFF=PSMODE are not reflected to the PLL clock frequency
ON
7 VINTHI ON=The exception vectors are located at 0xFFFF_0000.
OFF=The exception vectors are located at 0x0000_0000.
OFF
8 USB_S Use USB-Host (CN3) / USB-Function
ON=USB-Host (CN3)
OFF=USB-Function (CN4)
OFF
8 1
ON Default